• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.6
• /
• pp.87-93
• /
• 1994

This paper describes on the establishment of an optimal internal grinding conditions for the purpose of improving the grinding efficiency against to the high-speed grinding. Through the fundamental grinding tests for the brittle and hardened material, we are concluded that high-speed internal grinding is effective to improve the grinding accuracy as well as the grinding efficiency. The obtained results are as follows: (1) Under the speed ratio $(V_w/V_g)$ is constant, it is possible to increase the grinding efficiency with satifying the constraint conditions. (2) Increasing the wheel velocity, surface roughness and out-roundness are improved. (3) Under the wheel depth of cut is constant and increasing the speed ratio, workpiece residual stress is decreased. The described method, in this paper, is capable of determining the optimum internal grinding conditions taking into account some constraint conditions, and practical algorithm for optimum internal grinding conditions are presented.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.6
• /
• pp.38-49
• /
• 1994

In this study, grindability of some representative engineering ceramics are experimentally investigated using resin bond diamond wheel with conventional surface grinding machine, and proper grinding conditions which can be obtained from various experimental results are established also for mechanical components which are proper to domestic circumstances with high reliability. And through the results of experiment, it is confirmed that grinding energies of the ceramics, especially in the case of $Al_2O_3$, are lower than steel with same machining condition in the conventional grinding because of their fine-brittle fracture mode type removal process, though the ceramics are well-known to unmachinable materials. And moreover, the total pass numbers needed for spark-out process to be completed are depend on their mechanical properties because that grinding stiffness is different from each other. The grinding force, ginding power and ground surface roughness are also measured and compared. Furthermore, the experiments carried out in this study, some useful results are obtained with can guide to grind engineering ceramics with conventional surface grinding machine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.1
• /
• pp.99-111
• /
• 2016

This paper presents an integrated fault diagnosis algorithm for driving motor of In-wheel independent drive electric vehicle. Especially, this paper proposes a method that integrated the high level fault diagnosis and the low level fault diagnosis in order to improve a robustness and performance of the fault diagnosis system. The high level fault diagnosis is performed using the vehicle dynamics analysis and the low level fault diagnosis is carried using the motor system analysis. The validity of the high level fault diagnosis algorithms was verified through $Carsim^{(R)}$ and MATLAB/$Simulink^{(R)}$ cosimulation and the low level fault diagnosis's validity was shown by applying it to a MATLAB/$Simulink^{(R)}$ interior permanent magnet synchronous motor control system. Finally, this paper presents a fault diagnosis strategy by combining the high level fault diagnosis and the low level fault diagnosis.

• International Journal of Automotive Technology
• /
• v.7 no.3
• /
• pp.309-314
• /
• 2006

In this paper, the ride comfort from a computer simulation was compared to the experimental result. For measuring ride comfort of a passenger car, acceleration data was obtained from the floor and seat during highway running with different speeds. The measured acceleration components were multiplied by the proper weighting functions, and then summed together to calculate overall ride values. Testing several passenger cars, the ride comforts were compared. In order to investigate the effect of vibration signals on the steering wheel, an apparatus to measure the vibrations and weighting functions on the steering wheel were designed. The effect of the steering accelerations on the ride comfort were investigated and added for the overall ride comfort. For the computer simulations, Korean dummy models were developed based on the Hybrid III dummy models. For the Korean dummy scaling, the national anthropometric survey of Korean people was used. In order to compare and check the validity of the developed Korean dummy models, dynamic responses were compared to those of Hybrid III dummy models. The computer simulation using the MADYMO software was also compared to the experimental results.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.11
• /
• pp.24-34
• /
• 2019

An automotive automatic transmission is a popular power-transmitting device in passenger vehicles, as it provides various speed ratios for diverse driving conditions with easy manipulation and smooth gear shifting. The transmission is mainly composed of input and output shafts, planetary gear sets, brakes/clutches, and housing, and it yields multiple forward gears and one reverse gear by actuating the shifting devices of the brakes and clutches. In developing a new transmission, kinematic configurations of a transmission, which presents a brief structure and actuation schemes for speed ratios, need to be checked to determine if the structure can be assembled in a layout. It is impossible for a transmission concept having any interference in connecting main components to be developed further in the design process, since connection interference leads to failure of a layout design in the 2-D plane. In this research, an analysis of the assemblability of a front-wheel drive automatic transmission is carried out on an example concept design by applying the vertex addition algorithm based on graph theory.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.13 no.1
• /
• pp.99-108
• /
• 2014

Recently, the interest in autonomous vehicle which is an aggregate of the automotive control technology is increasing. In particular, researches on the self-localization technology that is directly connected with stable driving of autonomous vehicle have been performed. Various dead reckoning technologies which are solutions for resolving the limitation of GPS have been introduced. However, the conventional dead reckoning technologies have two disadvantages to apply on the autonomous vehicle. First one is that the expensive sensors must be equipped additionally. The other one is that the accuracy of self-localization decreases caused by wheel slip when the vehicle's motion changed rapidly. Based on this background, in this paper, the wheel speed sensor which is equipped on most of vehicles was used and the dead reckoning algorithm considering wheel slip ratio was developed for autonomous vehicle. Finally, in order to evaluate the performance of developed algorithm, the various simulation were conducted and the results were compared with the conventional algorithm.

• International Journal of Automotive Technology
• /
• v.6 no.1
• /
• pp.23-28
• /
• 2005

The presented investigation of shift clonk in a vehicle with front-wheel drive shows how a detailed analysis of the complete acoustic system with respect to excitation, transfer and radiation foremost enables possibilities of noise reduction to be worked out. One of the most important basics for the shift clonk analysis was a synchronous measurement of both, torsional vibrations in the drive train on the excitation side as well as airborne and structure-borne noise signals on the transfer and radiation side. Thus, root causes could be identified and improvement measures of the internal shift system could be worked out. An analysis of the transfer paths by means of airborne and structure borne noise measurements made evident that the side shafts were responsible for the disturbing frequencies in the transfer paths. With the help of the FE-simulation it was possible to develop measures of structure optimisation for the side shaft system. The realisation of these measures clearly reduced the shift-noises in the vehicle interior.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.6
• /
• pp.93-100
• /
• 2003

This paper describes the thermoelastic instability arising from friction heat generation in braking and proposes the finite element methods to predict the variation of temperature and thermal deformation. In a conventional disc brake analysis, heat generation is only related with wheel speed and friction material and the interface pressure between disc and pad is assumed constant. But under dynamic braking conditions, the frictional heat causes the thermoelastic distortion that leads to more concentrated contact pressure distribution and hence more and more non-uniform temperature. In this paper, to complete the solution of the thermomechanically coupled problem, the linear relation model between pressure and temperature is proposed and demonstrated in examples of a simple two dimensional contact problem. And the two dimensional model has been extended to an annular three dimensional disc model in order to consider more realistic geometry and to provide a more accurate critical speed for automotive brake systems.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.4
• /
• pp.68-75
• /
• 2012

This paper presents a study on the driveline output torque estimation using a discrete Kalman filter. The in-situ output shaft torque is first measured by a non-contacting magneto-elastic torque transducer. The linear state-space system equations are first derived and the discrete Kalman filter is designed based on the Kalman filter theory to recover the driveline output torque contaminated by random noises. In addition to using torque measurement, the estimation of the output torque using two angular velocities: the output and wheel, is also conducted. The experimental results show that the discrete Kalman filter can be effective for not only removing the random noise in output torque but also estimating the output torque without torque measurement.

• Journal of the korean Society of Automotive Engineers
• /
• v.8 no.4
• /
• pp.56-65
• /
• 1986

This paper theoretically analyzed the relations between the out-put braking torque and the wheel cylinder pressure in the leading-trailing drum brake for heavy duty truck as the characteristics of friction in break lining, comparing with the results derived from full-scale inertial brake dynamometer test in actual braking condition to develop reliable brake system in extensive using conditions. The main results obtained are as follows; 1) The characteristic curve representing the relations between BEF (Brake Effectiveness Factor) and Friction coefficient derived from theoretical analysis are consistent with the experimental results of dynamometer test. 2) According to the results of dynamometer test, the friction coefficient of brake lining is subject to initial brake speed and the actual using temperature in brake system.