• International Journal of Automotive Technology
• /
• 제8권2호
• /
• pp.225-232
• /
• 2007

A tooth profile modification for loaded gears is used to avoid a tooth impact. Since a tooth profile error causes amplification of the cumbersome whine noise in automotive gear transmissions, an optimal quantity of tooth profile modifications must be obtained for good performance in the vibration sense. In this paper, a tooth profile modification curve considering profile manufacturing errors and elastic deformation of the gear tooth is formulated; in addition, transmission errors of the gear system with modified teeth are verified. The equivalent excitation due to transmission errors is formulated. For experimental evaluation of the transmission error, the transmission error for a simple gear system was measured by two rotational laser vibrometers. Finally, we perform a comparative analysis between the calculated and measured responses to the excitations due to the transmission error to verify the practicability of the application to automotive transmissions.

• 한국자동차공학회논문집
• /
• 제22권7호
• /
• pp.1-7
• /
• 2014

A variable displacement vane pump is possible to improve the fuel economy by varying the pump capacity with a vane mechanism according to the engine operating speed range and reducing its driving torque. In general the experimental evaluation of the vane pump for the transmission has been performed mainly not with the vehicle or dynamometer test rig but with component test rig due to the implementation and safety problems. In this paper, in order to evaluate the performance of the developed vane pump as well as the compatibility with other rotary and hydraulic components of the target transmission, the transmission dynamometer based test rig is implemented where the developed pump is built into it and then the variable pump capacity and effect of power reduction are investigated experimentally.

• 오토저널
• /
• 제14권2호
• /
• pp.44-53
• /
• 1992

Automotive transmission is the principle component of vehicle driving system, which transmits the adjusted engine power. The automation of transmission arises from the annoyance of transmission operation such as the frequent stop/start of vehicle and the shifting transients. The study on the optimal shifting condition for the automation of transmission needs the investigation of shifting transients. However, the dynamic modeling theory during transient period is not well-established. In this study, the techniques of dynamic modeling for the power transmission system with Merrite-Wilson gear train are presented. To predict the shifting transients, a driving simulation program is developed, and the results of the analysis are cross-checked in the field test.

• Journal of Welding and Joining
• /
• 제29권6호
• /
• pp.45-48
• /
• 2011

In this research, laser welding of automotive transmission components was investigated to replace electron beam welding which is normally conducted under vacuum condition. Fiber laser welding was applied to the automotive transmission components - hub clutch and annulus gear. In the component welding, the laser welding parameters were optimized to eliminate spatters and the end crater. By applying laser welding to the transmission parts, the process time could be reduced up to 70% compared with the current electron beam welding process.

• 한국자동차공학회논문집
• /
• 제5권5호
• /
• pp.73-85
• /
• 1997

An automatic transmission is an important element of automotive power systems that allows a driving convenience. Compared to a manual transmission, however, it has a few problems in efficiency, shift feel, and maintenance. To improve these, it is imperative to understand the dynamics of automatic transmissions. This paper develops a dynamically-correct model of an automatic transmission, using the bond graph method. The bond graph method is ideally suited for modeling power systems, because the method is based on generalized power variables. The bond graph method is capable of providing correct dynamic constraints and kinematic constraints, as well as the governing differential equations of motion. The bond graph method is applied to 1-4 in-gear ranges, as well as various upshifts and downshifts of an automatic transmission, which allows an accurate simulation of an automatic transmission. Conventional automatic transmission models have no dynamic constraint, which do not allow correct simulation studies.

• 한국자동차공학회논문집
• /
• 제3권3호
• /
• pp.79-89
• /
• 1995

Rattle noise occurs at manual transmission as idling and driving of a automotive. It can be solved by torsional characteristics of a clutch disc. A clutch disc consist of a region of pre-damper and main-damper. Rattle noise is affected by pre-damper and main-damper equipped for a torsional spring and friction washer. Pre-damper range covers noise radiating from manual transmission when engine is idling and main-damper range covers noise when engine is driving. The aim of this reserch is to clear transmission rattle noise by way of torsional characteristics of a clutch disc. The experiment is carried out as idling and driving of a automobile equipped for 1.5L MPI engine, dry single-disc type clutch and manual transmission. In this study, the results show for a vibration of manual transmission as idling and driving can be cleared by a clutch disc of Pre-damper type.

• 한국자동차공학회논문집
• /
• 제24권3호
• /
• pp.372-378
• /
• 2016

Clutch torque control is the key to the ride comfort improvement of a vehicle equipped with AMT (automated manual transmission). For such control, the torque transfer starting point, known as the "kiss point," should be indicated or at least estimated to compensate for the clutch torque. The kiss point changes due to wear, high temperature, and fatigue; as such, it should be estimated while the vehicle is being driven. In this study, the method of kiss point active estimation for an AMT vehicle with a dry-type clutch was devised. The kiss point is learned while the engine is in an idle state and while the transmission is at a neutral gear position. It is determined when the input shaft of the transmission starts to rotate by slowly engaging the clutch. The noise of the shaft speed signal during the slow engagement process is filtered for accurate control. The kiss point estimation at various clutch engagement speeds was analyzed via a vehicle test.

• 한국자동차공학회논문집
• /
• 제22권4호
• /
• pp.89-97
• /
• 2014

As the digital control technologies in automotive industry have advanced, electronic control units(ECUs) play a key-role to improve system performance. Transmission control unit(TCU) is a shifting controller for automatic transmission of which major functions are to determine the shift and manage the shifting process considering the various sensor signal on transmission and driver's commands. As with any ECU in vehicle, TCU performs complex algorithms such as shift control, diagnostic and failsafe functions. However, firmware design analysis is hardly possible by the reverse engineering due to code protection. Transmission simulator is a hardware-in-the-loop simulator which enables TCU to work in normal mode by simulating the electrical signal of TCU interface. In this research, diagnosis and failsafe algorithm implemented on commercialized TCU is analyzed by using the transmission simulator that is developed for wheel loader construction vehicle. This paper gives various experimental results on the proportional solenoid current trajectories for different operating modes, error detection criterion and limphome mode gears for all the possible cases of clutch malfunction. The derived results for conventional TCU can be applied to the development of inherent TCU algorithms and the transmission simulator can also be utilized for the test of TCU to be developed.

• 한국실천공학교육학회논문지
• /
• 제1권1호
• /
• pp.51-54
• /
• 2009

In or automotive engineering education is introduced. Main objective of the system is teaching disassemble/assemble procedure of automatic transmission of a vehicle to students, who study automotive engineering. System includes vehicle transmission, set of tools and mechanical facilities, two video cameras, computer with developed software, HMD glasses and two LCD screens. Developed software gives instructions on assembling and disassembling processes of real vehicle transmission with the help of augmenting virtual reality objects on the video stream. Overlaying of 3D instructions on the technological workspace can be used as an interactive educational material. In disassembling process, mechanical parts which should be disassembled are augmented on video stream from video cameras. Same is done for assembling process. Animation and other visual effects are applied for better indication of the current assembling/disassembling instruction. During learning and training, student can see what parts of vehicle transmission and in which order should be assembled or disassembled. Required tools and technological operations are displayed to a student with the help of augmented reality, as well. As a result, the system guides a student step-by-step through an assembly/disassembly sequence. During educational process a student has an opportunity to return back to any previous instruction if it is necessary. Developed augmented reality system makes educational process more interesting and intuitive. Using of augmented reality system for engineering education in automotive technology makes learning process easier and financially more effective.

• 한국자동차공학회논문집
• /
• 제25권3호
• /
• pp.367-373
• /
• 2017

In this paper, a new shift map was proposed to improve the fuel economy of a transmission mounted electric device(TMED) type dual clutch transmission(DCT) plug-in hybrid electric vehicle(PHEV) by considering transmission and motor losses. To construct the shift map, powertrain efficiencies of the engine-DCT-motor were obtained at each gear step. A shift map that provides the highest powertrain efficiency was constructed for the given wheel torque and vehicle speed. Simulation results showed that the fuel economy of the target PHEV can be improved by the new shift map compared with the existing engine optimal operating line(OOL) shift control.