• 소성∙가공
• /
• 제18권1호
• /
• pp.39-44
• /
• 2009

This paper is concerned with forming technology of an automotive front side member part with ultra high strength steel sheet of DP980. The forming technology considered in this paper is the draw & form type, which installs the upper pad and lower pad to produce the complicated shape of ultra high strength steel sheet. In order to produce sound product, comparison between form type and draw & form type and between draw type and draw & form type are investigated by FE-analysis. FE-analysis is carried out with commercial sheet metal forming analysis S/W, DYNAFORM. It was shown from FE-analysis that the draw & form type satisfied the required specifications such as the dimensional accuracy and soundness of automotive front side member part. The effectiveness of the analytical result was verified by the experiment. From this investigation, the draw & form type is proved to be able to supply useful forming technology in forming ultra high strength steel.

• Journal of the Korean Data and Information Science Society
• /
• 제17권4호
• /
• pp.1299-1307
• /
• 2006

This study investigates solving production problems in an automotive stamping plant using Finite Element (FE) analysis. The fundamentals of stamping, metal plasticity and FE analysis are developed. In this paper, we provide the basis for a simulation of the stamping of a production part, the automotive rear floorpan. On-plant factorial Design of Experiments (DoE) were simulated using the floorpan model. The accuracy of the simulations was undetermined because of variability in the DoE results. Predictions of flange shape, wrinkling and thickness show qualitative agreement with manufactured parts and indicate that simulating an industrial part is feasible.

• 한국자동차공학회논문집
• /
• 제5권4호
• /
• pp.152-159
• /
• 1997

This paper presents a vibration analysis method of crank shaft of six cylinder internal combustion engine. For simple analysis journal, pin and arm parts were assumed to have uniform section. Transfer Matrix Method was used, considering branched part and coordinate transformation part. Natural frequencies, modeshapes and transfer functions of crank shaft were investigated based upon the Euler beam theory: It was shown that the calculated natural frequencies, modeshapes agree well with the existing paper results.

• 소성∙가공
• /
• 제24권4호
• /
• pp.280-286
• /
• 2015

Hemming is used to connect two sheet metal components by folding the edge of an outer panel around an inner panel to create a smooth edge. The minimization of hemming defects is critical to the final quality of automobile products because hemming is one of the last operations during fabrication. Designing the hemmed part is not easy and is influenced by the geometry of the bent part. Therefore, the main problem for automotive parts is dimensional accuracy since formed products often deviate geometrically due to large springback. Few numerical approaches using 3-dimensional finite element model have been applied to hemming due to the small element size which is needed to properly capture the bending behavior of the sheet around small die corner and the comparatively big size of automotive opening parts, such as doors, hoods and deck lids. The current study concentrates on the 3-dimensional numerical simulation of hemming for an automotive door. The relationship between the design parameters of the hemming operation and the height difference defect is shown. Quality improvement of the automotive door can be increased through the study of model parameters.

• 한국생산제조학회지
• /
• 제19권2호
• /
• pp.260-266
• /
• 2010

Today's consumers are looking for emotional design which can fulfill their own potential desire. Emotion varies according to individual circumstance, age, sex, culture, education, profession and so on. Automotive instrument panel design is the most important part of interior design, because it affects the impression of interior design and has the equipments for safety, entertainment and various information. Thus, this study was performed to apply emotional design to automotive instrument panel which is the most important part of automotive interior, and find the best bonding conditions to build instrument panel efficiently by comparing mechanical properties in thermoplastic resin of polyethylene (PE) adhesion. Satisfactory adhesion was executed in ultrasonic welding for the same materials of PE. The best welding conditions were found to be welding time of I second, welding pressure of 250 kPA for PE-PE welding. Dissimilar materials were adhered when adhesion and ultrasonic welding were performed at the same time.

• 한국자동차공학회논문집
• /
• 제14권5호
• /
• pp.1-8
• /
• 2006

The Steer-By-Wire(SBW) system replaces complex mechanical linkages of the current steering system with electric motors, sensors, and electronic control units. However, the SBW system should guarantee its safety and reliability before commercialization, and therefore, a reliable and robust fault-tolerant technology has to be implemented. This paper proposes a fault-tolerant control algorithm for the SBW system. Based on careful analysis on propagation effects of sensor faults, a reliable fault-tolerant control strategy has been developed. The fault-tolerant controller consists of a fault detection part that monitors and detects faults in the steering wheel and road wheel sensors, and a reconfiguration part that switches to normal sensor signal based on fault detection information. It has been demonstrated by simulation that the proposed algorithm detects sensor faults accurately and enables reliable steering control under various dynamic fault situations.

• 한국정보통신학회논문지
• /
• 제15권9호
• /
• pp.1985-1992
• /
• 2011

PE(Passive Entry)는 자동차 운전자가 스마트 키를 직접 사용하지 않고 차량의 문을 열거나 닫는 자동차 기술이다. PG(Passive Go)는 운전자가 스마트 키를 갖고 차량 내에 있을 때 시동을 걸거나 끄는 기술이다. 이러한 2가지 기능을 합쳐서 PEG라 부른다. PEG의 핵심 기술 중의 하나인 LF(Low Frequency) 안테나 구동기는 명령을 처리하는 디지털 블록과 sine 파를 발생시키는 아날로그 블록으로 구성되어 있다. LF 안테나 구동기의 디지털 블록은 MCU(혹은 ECU)로부터 명령을 받아서 요청된 명령을 수행하며, 내부의 FIFO 블록에 안테나 구동 관련 명령 및 데이터를 저장한다. FIFO에서 명령을 읽어내 이에 대응하는 조치를 취하며 변조된 LF 데이터를 아날로그 블록에 전달하면 아날로그 블록은 sine 파를 생성하여 안테나를 통해 외부로 전달한다. 설계된 LF 안테나 구동기용 디지털 블록은 기존의 제품과 비교하여 더 빠른 속도로 LF 데이터 전송을 수행할 수 있다. 이의 응용 분야는 자동차용 PEG 및 건물의 출입문 개폐에 활용이 가능하다.

• 한국기계가공학회지
• /
• 제7권3호
• /
• pp.36-40
• /
• 2008

This study is analyzed by the simulation of automotive steering system. The maximum equivalent stress of $2.2418{\times}109Pa$ and the maximum total displacement of 0.014929m are shown at the universal joint and its lower part respectively. As the minimum cycle of 34.047 is shown at the universal joint in case of fatigue analysis, it is possible to have greatest damage at this part. In case of natural frequency analysis at vibration, its frequency of 47 to 59Hz is occurred generally. The maximum total displacement of 0.5m is shown at handle on the natural frequency of 57 to 58Hz. And the displacement over 2m is shown at the lower part of universal joint on the natural frequency of 58 to 59Hz. As the basis of the simulation analysis of steering system, passenger's comfort of car body can be improved in the design of practical part and the design effect necessary to safe driving can be promoted.

• 소성∙가공
• /
• 제26권2호
• /
• pp.101-107
• /
• 2017

Aluminum alloys are widely used in automotive industry because of their high strength-to-density ratio and excellent corrosion resistance. However, conventional cold stamping of aluminum alloys leads to low formability and excessive spring-back. To overcome these problems, Hot Forming Quenching (HFQ) is applied to manufacture automotive part using aluminum alloy. The purpose of this study is to investigate effect of forming temperature on spring-back in HFQ of T6 heat treated AA6061 sheet. In this study, hat shape forming test was adopted to evaluate spring-back characteristics according to various forming temperatures. In additions, the test was also performed with warm forming conditions in comparison with dimensional accuracy of HFQed part. The experimental results showed that dimensional accuracy of HFQed part was superior to warm formed part and amount of spring-back was decreased as forming temperature rise.

• International Journal of Automotive Technology
• /
• 제7권5호
• /
• pp.547-554
• /
• 2006

This paper is concerned with an optimal control suspension system using the preview information of road input based on a quarter car model. The main purpose of the control is to combine good vibration isolation characteristics with improved attitude control. The optimal control law is derived with the use of calculus of variation, consisting of three parts. The first part is a full state feedback term that includes integral control acting on the suspension deflection to ensure zero steady-state deflection in response to static body forces and ramp road inputs. The second part is a feed-forward term which compensates for the body forces when they can be detected, and the third part depends on previewed road input. The performance of the suspension is evaluated in terms of frequency domain characteristics and time responses to ramp road input and cornering forces. The effects of each part of the suspension controller on the system behavior are examined.