• Journal of KSNVE
• /
• v.9 no.4
• /
• pp.761-768
• /
• 1999

This paper presents an NVH test of Automotive power steering system performed at a half-car Test-rig. The test was done for neutral and full turn(or relief) conditions in steering wheel at a fixed rpm first, then followed by the same conditions for the rpm run-up. The sound intensity measurement verified the results from the frequency and order analysis, especially about the identification of major noise sources and their dominant frequencies. The results from thie study can be utilized in the system noise tuning when a new steering component is installed. In particular, the noise and vibration reduction at the relief condition will be accomplished through the knowledge obtained from this study and from the on-going research on the hose tuning techniques usign silencers and tuning cable inserted in the pressure hose.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.4
• /
• pp.84-92
• /
• 1997

Among the various sources of vehicle interior noise, this paper concerns the road induced noise ; the identification of its transfer path by using experimental method. Multiple input and single output model is taken as a noise generation model. Because it is impossible to measure the road imput forces directly, the acceleration signals are measured on four axle;three directions for each point. By considering the cross correlations of input signals, four uncorrelated source groups are taken. Multiple coherence function is employed to investigate the contribution of each group. In addtion, to identify the detailed path through the suspension systems, the contributions of all possible paths are ranked by using the coherence functions between interior noise and the relative accelerations of connections such as bushings and mountings. Measurements are performed with passenger vehicle traveling on concrete and asphalt roads at 60㎞/h.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.3
• /
• pp.55-62
• /
• 1993

Autoregressive moving average(ARMA) model which is a time domain parametric modeling method is implemented for modeling and reproducing characteristics of exhaust noise of an automobile in various RPM range. Experiments have been carried out using 9 set of exhaust noise signals measured at 1,000-3,000 RPM range. Characteristics of sampled signals were estimated using ARMA modeling and Akaike's FPE(final prediction error) criterion to define exact model structure and for model validation. The digital filter consisted of the esitmated ARMA(70,1) model parameters was programed to reproduce exhaust noise. The spectral analysis of reproduced noise is very close to original. The results show that our approaching technique for reproducing acoustic characteristics is valid and feasible to apply in the field of noise quality control.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.5
• /
• pp.423-430
• /
• 2013

The characteristics of friction noise due to the friction-velocity curve is experimentally investigated through the pin-on-disk setup. The rotation speed of the disk is controlled in order to produce the sliding speed variation. Then, the friction coefficient and the corresponding friction noise are simultaneously measured with respect to the sliding speed between the steel disk and aluminum pin. The experimental results show that the negative friction-velocity slope is essential in generating friction noise.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.6
• /
• pp.178-185
• /
• 2001

This paper describes the correlation between the interior noise and the trunk wall vibration. Using the vibro-acoustic reciprocity, effect of the trunk wall vibration on the compartment noise is investigated on a medium size car. In the low frequency range, vehicle interior noise is dominated by several acoustic modes of the passenger compartment and the vibration modes of the surrounding shell parts. Especially, vibration of the trunk wall radiates sound and it is transferred through holes on the package tray into the passenger compartment. This paper experimentally reveals that sound can be well produced at some particular vibration modes of the trunk lid and it strongly influences the compartment noise through package tray holes. Contributions of the trunk walls to the interior noise are estimated by measuring the acoustic-structural transfer function, based on the vibro-acoustical reciprocity theorem.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.1
• /
• pp.79-86
• /
• 1997

The need for an active exhaust moise controller has been growing as an reinforcement of exhaust noise regulation, high power output and improvement of average fuel economy. In this study, for development of this active exhaust noise controller, the implementation of a composition of realtime control algorithm for active exhaust noise control and the construction of simulator for realtime control algorithm for active exhaust noise control has been investigated. Also, in order to implement active exhaust noise control with this simulator, the feasibility model for control of vehicle exhaust noise control is suggested.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.1
• /
• pp.28-34
• /
• 2014

This study provides the numerical finite-element method(FEM) estimating the friction noise induced by the negative slope in the friction-velocity curve. The friction noise due to the friction-velocity curve is experimentally investigated through the pin-on-disk setup. The measured squeal frequency is estimated by FEM. The friction curve is measured by the friction test, then it is applied to the complex eigenvalue analysis. The results shows that the experimental squeal frequency can be determined by the FEM analysis. Also, it is emphasized that the negative friction-velocity slope is essential in generating friction noise in the pin-on-disc system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.665-670
• /
• 2001

The purpose of this paper is to verify a finite element model of an automotive exhaust system using Modal testing. In general, a lot of finite element models are used in initial design step of automotive development. One of them is a finite element model of an exhaust system. Verification on the finite element model of an automotive exhaust system is indispensable. In this paper, a finite element analysis on the exhaust system using MSC/NASTRAN is carried out, and the results are compared with those obtained by modal testing. By comparing MAC values of the analytical modes with the experimental modes, the finite element model of the automotive exhaust system is verified.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.994-998
• /
• 2004

Hybrid method is used to suppress vibration of an automotive roof surface. The hybrid method proposed in this paper is implemented experimentally using both viscoelastic and piezoelectric material. The piezoelectric material is used to control the vibration of automotive structure for lower range of frequencies and the experiment of vibration control using viscoelastic material has been carried out suppress vibrations of high frequency range mark. At first the plate controlled by using hybrid method has been .implemented to verify the performance for suppressing vibration. Then the experiment has been applied to the automotive roof structure.

• Journal of the korean Society of Automotive Engineers
• /
• v.16 no.3
• /
• pp.30-35
• /
• 1994