• 한국기계가공학회지
• /
• 제20권11호
• /
• pp.80-85
• /
• 2021

The gasification of coffee leaves, which are a type of biomass waste, was conducted on a pilot of a downdraft fixed gasification system to investigate the gasification characteristics. The experiment was performed using a coffee leaf pellet size and a batch-type gasification system consisting of a gasifier, cooling cyclone, scrubber, and bag filter. It was found that the air-to-fuel ratio was 2.32 Nm³/kg·h and the reaction temperature was 700 ℃-900 ℃. However, the air flow rate changed to 0.45 Nm³/min, which was lower than the initial starting value depending on the temperature change during the gasification process. It was concluded that coffee leaves can be converted from biomass waste into useful synthetic gas as an alternative energy source.

• 한국자동차공학회논문집
• /
• 제21권2호
• /
• pp.104-113
• /
• 2013

New USNCAP has been carried out by NHTSA including front and side crash from MY2011. In this paper, test results for USNCAP Side crash were reviewed by statistical analysis. This review focused on side crash test results to investigate the effect of changes from new USNCAP side crash test protocol among 30 passenger cars. These results were summarized as followings. Total number of 5 star vehicles on the front seat dummy (16 vehicles, 53.3%) was slightly smaller than the rear seat's (17 vehicles, 56.7%) in MDB test. For the ES-2re dummy, chest injury, ie maximum rib deflection contributed to 66% in the mean value of $P_{joint}$. Pelvis injury was highly dependent upon performance up to 87% in the SID-IIs dummy cited on the rear seat in average $P_{joint}$. For Pole test, pelvis injury made contribution to the average performance to 83%. For standard deviation, it showed the largest value in the same body region as the mean value for each dummy. Overall front seat performance showed 14 vehicles, 44.6% with 5 star vehicles less than each MDB or Pole test result. This result showed that performances in MDB test were different pattern to Pole test on driver position. Number of 5star vehicles for overall side NCAP performance are 18 passenger cars (60%). Curtain airbag and driver thorax airbag were equipped in all test vehicles. One vehicle is equipped with thorax airbag in the rear seat. Results from two side tests considered as reliability problem, ie the cause for large standard deviation in side crash test. Consequently, the countermeasure for new USNCAP side crash test is essential to design the effective side structures for side collision and to control well dummy kinematics with curtain and thorax airbag in order to reduce chest and pelvis injuries.

• 한국자동차공학회논문집
• /
• 제8권6호
• /
• pp.259-266
• /
• 2000

Crash test data from different impact modes and threshold speeds were used to assess the effects of impact conditions on air bag electronic single point sensing (ESPS) activation requirements. The requirements are expressed in terms of the desired sensor activation time based on unbelted driver dummy kinematics. A crash discriminator pre-displacement is introduced to crash recognition algorithm to the ESPS. The new crash recognition algorithm named Velocity Energy Pre-displacement(VEPD) method is developed and the ESPS algorithm based on the VEPD technique is used to assess the ESPS system performance. It is shown that VEPD method correlates very well with desired sensor activation time and meets the activation requirement.

• 한국자동차공학회논문집
• /
• 제19권2호
• /
• pp.12-19
• /
• 2011

Real-world accident cases were investigated to understand injury characteristics of the elderly driver. A total 10 cases of car-to-car frontal crash accidents from passenger car including SUV claimed to domestic car insurance company were reviewed. The injury characteristics of the elderly were analyzed from personal information (gender, age), medical treatment record (medical certificate, curative days), vehicle information (model, air-bag, seatbelt) and damage information. This study showed that elderly driver has higher possibility of thorax injury than non-elderly's. Moreover, Injury type and severity were more severe than non-elderly driver at similar type accident conditions. Also, elderly driver's medical treatment period needs 3 times more than non-elderly driver's.

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2010년도 추계학술발표논문집 2부
• /
• pp.835-838
• /
• 2010

자동차 승객 안전에 대한 요구가 점차 확대 되어감에 따라 전방 충격으로부터 승객의 상해를 감소시키기 위한 각종 승객 안전장치 중 하나로, 에어백 시스템은 정면충돌 시 승객 사망률을 약 30%정도 저감시킬수 있다. 에어백은 충돌 시 일정한 힘 이상을 받게 되면 작동하도록 설계하여야 한다. 본 논문은 CATIA를 이용하여 3차원 설계를 하였으며, 해석 프로그램을 이용하여 사출성형품의 구조해석 및 사출 해석을 하여 최적화 하였다.

• 한국자동차공학회논문집
• /
• 제12권1호
• /
• pp.138-144
• /
• 2004

Occupant protection in the side impact of a vehicle becomes one of the most important issues today. So, to reduce development time and cost, it needs test equipment which conducts an accurate simulation of the side impact crash. This paper describes a new test method for side impact, which utilizes a standard 12inch-HYGE-type sled facility. If a side impact sled test can simulate vehicle intrusion very well, it will contribute to develop full-scale side impact crash performance. The newly developed sled test method enables simulation for dummy motion, injury, door velocity, trim crack, and vehicle structure to be accurate. Ant also this sled test method can be applied to the development of side air-bag.

• 대한기계학회논문집A
• /
• 제20권2호
• /
• pp.408-413
• /
• 1996

A self-diagnostic, air-damped, piezoresitive, cantilever-beam microaccelerometer has been designed, fabricated and tested for applications to automotive electronic airbag systems. A skew-symmetric proof-mass has been designed for self-diagnostic capability and zero transverse sensitivity. Two kinds of multi-step anisotropic etching processes are developed for beam thickness control and fillet-rounding formation, UV-curing paste has been used for sillicon-to-glass bounding. The resonant frequency of 2.07kHz has been measured from the fabricated devices. The sensitivity of 195 $\mu{V}$/g is obtained with a nonlinearity of 4% over $\pm$50g ranges. Flat amplitude response and frequency-proportional phase response have been obserbed, It is shown that the design and fabricaiton methods developed in the present study yield a simple, practical and effective mean for improving the performance, reliability as well as the reproducibility of the accelerometers.

• 한국안전학회지
• /
• 제11권4호
• /
• pp.97-106
• /
• 1996

Some of accidents are based on unstable chemical substances. These chemicals are easily decomposed or Ignited by heats or mechanical shocks like sodium azide. Sodium azide is commonly used as propellant for inflating automotive safety bags and the other chemical manufacturing purposes. The investigation of thermal hazard potential of sodium azide is very important because unexpected traffic accident can be occureed. The experiments were carried out by DSC, TG an ARC in air, oxygen, argon and nitrogen atmosphere. The decomposition temperatures were about $410^{\circ}C$~$420^{\circ}C$ by DSC and $330^{\circ}C$~$370^{\circ}C$ by ARC, this is very significant result for treatment of chemical. The heats of decomposition were about 81 kcal/mol in ai. and 10 kcal/mol in other atmosphere.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2002년도 추계학술대회 논문집
• /
• pp.53-54
• /
• 2002

Plasma ignition method has been applied in various fields particularly to the rocket propulsion, pyrotechnics, explosives, and to the automotive air-bag system. Ignition method for those applications should be safe and also operate reliably in hostile environments such as; electromagnetic noise, drift voltage, electrostatic background and so on. In the present study, a semiconductor bridge (SCB) plasma ignition device was fabricated and its plasma characteristics including the propagation speed of the plasma, plasma size, and plasma temperature were investigated with the aid of the visualization of micro scale plasma $(i.e.,\;\leq\;350\;{\mu}m)$, which generated from a Micro-Electro-Mechanical poly-silicon semiconductor bridge (SCB).

• International Journal of Automotive Technology
• /
• 제7권5호
• /
• pp.571-577
• /
• 2006

This paper deals with dynamic tensile characteristics for the polypropylene used in an IP(Instrument Panel). The polypropylene is adopted in the dash board of a car, especially PAB(Passenger Air Bag) module. Its dynamic tensile characteristics are important because the PAB module undergoes high speed deformation during the airbag expansion. Since the operating temperature of a car varies from $-40^{\circ}C$ to $90^{\circ}C$ according to the specification, the dynamic tensile tests are performed at a low temperature($-30^{\circ}C$), the room temperature($21^{\circ}C$) and a high temperature($85^{\circ}C$). The tensile tests are carried out at strain rates of six intervals ranged from 0.001/sec to 100/sec in order to obtain the strain rate sensitivity. The flow stress decreases at the high temperature while the strain rate sensitivity increases. Tensile tests of polymers are rather tricky since polymer does not elongate uniformly right after the onset of yielding unlike the conventional steel. A new method is suggested to obtain the stress-strain curve accurately. A true stress-strain curve was estimated from modification of the nominal stress-strain curves obtained from the experiment. The modification was carried out with the help of an optimization scheme accompanied with finite element analysis of the tensile test with a special specimen. The optimization method provided excellent true stress-strain curves by enforcing the load response coincident with the experimental result. The material properties obtained from this paper will be useful to simulate the airbag expansion at the normal and harsh operating conditions.