• International Journal of Automotive Technology
• /
• v.8 no.1
• /
• pp.27-31
• /
• 2007

The number of vehicles employing diesel engines is rapidly rising. Accompanying this trend, application of an after-treatment system is strictly required as a result of reinforced exhaust regulations. The Diesel Particulate Filter (DPF) system is considered as the most efficient method to reduce particulate matter (PM), but the improvement of a regeneration performance at any engine operation point presents a considerable challenge by itself. Therefore, the present study evaluates the effect of fuel injection characteristics on regeneration performance in a DOC and a catalyzed CR-DPF system. The temperature distribution on the rear surface of the DOC and the exhaust gas emission were analyzed in accordance with fuel injection strategies and engine operating conditions. A temperature increase more than BPT of DPF system was obtained with a small amount fuel injection although the exhaust gas temperature was low and flow rate was high. This increase of temperature at the DPF inlet cause PM to oxidize completely by oxygen. In the case of multi-step injection, the abrupt temperature changes of DOC inlet didn't occur and THC slip also could not be observed. However, in the case of pulse type injection, the abrupt injection of much fuel results in the decrease of DOC inlet temperatures and the instantaneous slip of THC was observed.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.2
• /
• pp.374-384
• /
• 2016

Concern about air pollution is gradually rising up in domestic and foreign, automotive and fuel researchers are trying to reduce vehicle exhaust emissions, through a lot of approaches, which consist of new engine design and innovative after-treatment systems, using clean (eco-friendly alternative) fuels and fuel quality improvement. This research is proceeding by two main issues : exhaust emissions and PM particle emissions of gasoline vehicle. Exhaust emissions, non-regulated emissions and PM (particulate matter) particles of automotive are causing many problems which ambient pollution and harmful effects on the human body. The main particulate fraction of automotive exhaust emissions consists of small particles. Because of their small size, inhaled particles can easily penetrate deep into the lungs. The rough surfaces of these particles make it easier for them to combine with other toxins in the environment. Thus, the hazards of particle inhalation are increased. Based on the oxygenated fuel additive types (MTBE, Bio-ETBE, Bio-ethanol, Bio-butanol), this paper discussed the influence of oxygen contents on gasoline vehicle exhaust emissions, non-regulated emissions and nano-particle emissions. Also, this paper assessed exhaust emission characteristics at 2 type test modes. The test modes were FTP-75 and HWFET. All measurement items be verified less than the value of regulated emissions. It could be known difference increase and decrease by each measurement item depending on increase the oxygen contents.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.6
• /
• pp.151-158
• /
• 2007

The static and dynamic behaviour of VGT and EGR systems has a significant impact on overall engine performance, fuel economy and exhaust emissions. This is because they define the state and composition of the air charge entering the engine. This work focused on the effect of the aperture ratio of VGT and EGR on the emission and flow characteristics under partial loads conditions. The investigation carried out using 2 liter PCCI 4 cylinder diesel engine with VGT and EGR. The result of this study shows that smoke increases with increasing EGR rate and NOx decreases with increasing EGR rate. It was also found that the residual gas contents greatly impact on soot emission under partial load condition. Finally, it can be concluded that VGT and EGR aperture ratio can greatly impact not only on soot and NOx but also air charging.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.2
• /
• pp.65-73
• /
• 2007

The use of an Exhaust Gas Recirculation(EGR) for a diesel engine with variable geometry turbocharger(VGT) has confronted how to obtain the amount of EGR for NOx reduction requirement at wide operating range and less side effect. Through a combined effort of modeling(wave action simulation) and experiment, an investigation into the effect of EGR area ratio and pipe length on EGR characteristics of common rail diesel engine with VGT has been performed. For accurate computation, calibration of constants involved in empirical and semi-empirical correlations has been performed at a specific operating point, before of its use for engine simulation. From the results of this study, it was found that EGR rate is sharply increased with increasing EGR area ratio until area ratio of 0.3. However, the effect of EGR area ratio on EGR rate is negligible beyond this criteria. This study also investigates the effect of EGR pipe length on a EGR amount and pulsating flow characteristics at EGR junction. The results showed that the longer EGR pipe length, the lower EGR amount was achieved due to the flow loss resulting in lower amplitude of pressure wave.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.5
• /
• pp.35-44
• /
• 2011

In a spark ignition engine, a variable valve lift (VVL) system has been developed for high fuel efficiency and low power loss. However, changes in valve lift cause deviations of cylinder air charge which lead to individual cylinder equivalence ratio maldistribution. In this study, in order to reduce the maldistribution, we propose individual cylinder equivalence ratio estimation and control algorithms. The estimation algorithm calculates the equivalence ratio of each cylinder by using a mathematical engine model which includes air charging, fuel film, exhaust gas, and universal exhaust gas oxygen sensor (UEGO) dynamics at various valve lifts. Based on the results of estimated equivalence ratio, the injection quantity of each cylinder is adjusted to control the individual cylinder equivalence ratio. Estimation and control performance are validated by engine experiments. Experimental results represented that the equivalence ratio maldistribution and variation are decreased by the proposed algorithms.

• Journal of the korean Society of Automotive Engineers
• /
• v.7 no.1
• /
• pp.24-34
• /
• 1985

The study of unsteady gas exchange processes in the inlet and exhaust systems of the single-cylinder 4-stroke cycle spark ignition engine is presented in this paper. The generalized method of characteristics including friction, heat transfer, change of flow area and entropy gradients was used for solving the equations defining the gas exchange process. The path line calculation was also conducted to allow for calculation of the gas composition and entropy change along the path lines, and of the variable specific heat due to the change of temperature and composition. As the result of the simulation, the properties at each point in the inlet and exhaust pipe, pressure and temperature in the cylinder, and charging efficiency were obtained. Pumping loss and residual gas fraction were also computed. The effect of engine speed, exhaust and inlet pipe length on the pumping loss and charging efficiency were studied showing that the results were in agreement with what has been known from experiments.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.4
• /
• pp.85-92
• /
• 2000

The pulsating pressure waves are composed of fundamental frequency and higher order harmonics in exhaust pipe of engines. The nonlinearity in exhaust pipe is caused by their interactions. The error which is between prediction and measurement is induced by the nonlinearity. We can not explain this phenomenon using linear acoustic theory which is existing theory. So power spectrum which was used in linear theory is not useful. Bispectrum and bicoherence functions which are a higher order spectrum are applicable to explain this phenomenon. This paper proposes a nonlinear effect of pulsating pressure waves. The phenomenon proposed here is identified by using of higher order spectrum density functions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.5
• /
• pp.1-8
• /
• 2001

It is a present situation that the control on automobile emission is getting more restrictive and also the regulations for emission are changing greatly up to level of those advanced foreign countries. Specially, it has been many years that exhaust gases from gasoline automobile rather than from diesel is the major object concerned by Korea and other countries, and it is strongly required on the reduction techniques on harmful NOx and PM among those compositions. Thus, this research focused on the Exhaust Gas Recirculation (EGR) and the target for this research is heavy-duty turbo-diesel engine with Cooled EGR. Furthermore, this research has been made efforts to accomplish the regulation on emission for heavy duty diesel engine.

• International Journal of Automotive Technology
• /
• v.6 no.3
• /
• pp.197-203
• /
• 2005

This paper investigates the effect of oxygen composition in mixed fuel on the exhaust emissions for the direct injection diesel engine. These effects were tested to estimate the change in engine performance and exhaust emission characteristics when commercial diesel fuel and oxygenates blended fuels at a certain fuel and mixed ratio are used. Individual hydrocarbons $(C_1-C_6)$ in exhaust gases, as well as the total amount of hydrocarbons, were analyzed by using gas chromatography to find the mechanism by which smoke emission was remarkably reduced for various oxygenated fuels. The chromatograms between a diesel fuel and a diesel fuel blended DGM (diethylene glycol dimethyl ether), MTBE (methyl tert-butyl ether) and EGBE (ethylene glycol mono-n-butyl ether) were compared. The results showed that the number of individual hydrocarbons as well as the total number of hydrocarbons of oxygenated fuel reduced more remarkably than those of diesel fuel.

• Journal of the korean Society of Automotive Engineers
• /
• v.12 no.3
• /
• pp.41-52
• /
• 1990

In this study are determined the unsteady temperature and thermal stress fields for a domestic 4-cylinder, 4-cycle gasoline engine cylinder head by the three-dimensional finite element method. A representative part of the cylinder head is modelled as a combination of hexahedron isoparametric elements, and the time-dependent temperature and the heat transfer coefficient of the gas are imposed as the thermal boundary conditions for the engine speeds of 500 rpm and 2000 rpm. The obtained results, which are represented graphically, indicate that the amplitudes of temperature fluctuation during a cycle are about 10.deg. C and 3.deg. C respectively on the surface of combustion chamber, and the maximum temperature fields occur at 30.deg. , 10.deg. respectively before the initiation of the exhaust stroke. Thermal stress fields due to non-uniform temperature distributions show that compressive stress is much larger than tensile stress throughout a cycle. It is also found that the compressive stress varies with substantial amplitude between the exhaust port and ignition plug hole, and the high tensile stress with small fluctuation occurs between exhaust port and the adjacent head bolt hole.