• 한국기계연구소 소보
• /
• s.17
• /
• pp.49-59
• /
• 1987

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.847-852
• /
• 2003

The purpose of this paper is to develop the new deep mixing method installed automatic control equipments for the better construction in deep mixing and grouting. Civil, geotechnical, electronic, and communication experts have worked together for a long time for the development of automatic measuring devices using wire and wireless transmitting-receiving set. A series of laboratory and field experiments were carried out to check the reliability and field applicability of this system. New total automatic control system including automatic devices for checking angle, depth and quantity of injected grout was invented from the result of this research.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.11a
• /
• pp.762-763
• /
• 2002

Recently, automatic control or application of measuring instrument with computers is rapidly increasing. In this paper we designed automatic incubation system that has functions of control and monitoring of measuring instrument, analysis of measured data, and automatic control by using LabVIEW graphic program that can easily collect, control, analyze, and apply data. Then to inspect the system we produced Incubator. Internal environment is measured by a sensor and each device is setting and controlled to create the optimum environment after finding hatching environment of selected individual from Database file for incubation. Through this functions, problems of hatching rate and quality that were affected by minute change of hatching environment are dealt successfully with, and retrenchment of labor and cost is expected as well.

• Journal of Sensor Science and Technology
• /
• v.22 no.6
• /
• pp.387-392
• /
• 2013

Camera rigs for shooting 3D video are classified as manual, motorized, or fully automatic. Even in an automatic camera rig, the process of Stereoscopic 3D (S3D) video capture is very complex and time-consuming. One of the key time-consuming operations is capturing the distance parameters, which are near distance, far distance, and convergence distance. Traditionally these distances are measured by tape measure or triangular indirect measurement methods. These two methods consume a long time for every scene in shot. In our study, a compact laser distance sensing system with long range distance sensitivity is developed. The system is small enough to be installed on top of a camera and the measuring accuracy is within 2% even at a range of 50 m. The shooting time of an automatic camera rig equipped with the laser distance sensing system can be reduced significantly to less than a minute.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.04a
• /
• pp.247-252
• /
• 2004

Developed shape awareness technology and vision technology for optical ten slant in this research and including external form state of lens for the performance verification developed so that can be good achieve badness finding. And, establish to existing reflex data because inputting surface badness degree of scratch's standard specification condition directly, and error designed to distinguish from product more than schedule error to badness product by normalcy product within schedule extent after calculate the error comparing actuality measurement reflex data md standard reflex data mutually. Developed system to smallest 1pixel unit though measuring is possible 1pixel as 3.7$\mu\textrm{m}$${\times}$3.7$\mu\textrm{m}$(0.1369${\times}$10/sub-1/$\textrm{mm}^2$) the accuracy to 10/sub-1/mm minutely measuring is possible performance verification and trust ability through an experiment prove.

• Journal of Institute of Control, Robotics and Systems
• /
• v.3 no.4
• /
• pp.357-362
• /
• 1997

This paper suggests an automatic calibration technique for piezoelectric low pressure transducer measuring a pressure blow 500psi. The present calibration system embedded with error correction algorithm generates it's best you don't cut parts of wards like so dynamic pressure and compensates offset voltage and pressure error. It is shown via experimental results that the instrumentation accuracy has been improved and mean time between calibrations has been shortened.

• Journal of Sensor Science and Technology
• /
• v.5 no.2
• /
• pp.47-54
• /
• 1996

This paper deals with the electric field sensor and automatic measuring system of the time-varying space electric field produced by lightning discharges. The theoretical principle and the design rule of the measuring devices are investigated, and the semisphere-type electric field sensor and the signal process system are fabricated. From the calibration experiments, the frequency bandwidth of the measuring system ranges from 200 [Hz] to 1.56 [MHz] and the sensitivity is 0.96 [m V/V/m] as the amplification gain is 10. In addition, the electric field waveforms produced by lightning discharges are observed by the proposed electric field measuring system from June to August in 1995. The data is sampled with the time interval of 200 [ns] and is automatically recorded by transient signal analyzer(Necolet Pro 30), the resolution of which is 12 bit. And it is registered at personal computer. The electric field waveforms produced by intracloud discharge tend to be bipolar, with two or three narrow and fast rising pulses superimposed on the initial half-cycle.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.100-105
• /
• 2002

In general, manufacturing error originated in bad material, machine tool defection, tool defection, and tool breakage. When the manufacturing process is stable, the error is come from the tool wear. In common on-machine measurement, teaching probe and touch sensor are widely used, however in this thesis the automatic tool compensation system using electric touch point measuring system is developed and evaluated, and effective operating is proposed.

• International Journal of Highway Engineering
• /
• v.14 no.3
• /
• pp.77-85
• /
• 2012

Most of Automatic Accident Detection Algorithm has a problem of detecting an accident as traffic congestion. Actually, center's managers deal with accidents depend on watching CCTV or accident report by drivers even though they run the Automatic Accident Detection system. It is because of the system's detecting errors such as detecting non-accidents as accidents, and it makes decreasing in the system's overall reliability. It means that Automatic Accident Detection Algorithm should not only have high detection probability but also have low false alarm probability, and it has to detect accurate accident spot. The study tries to verify and evaluate the effectiveness of using Gaussian Mixture Model and individual vehicle tracking to adapt Accident Detection Algorithm to Center Management System by measuring accident detection probability and false alarm probability's frequency in the real accident.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.9
• /
• pp.1029-1036
• /
• 2014

Several types of automatic 3D scanners are available for use in the 3D scanning industry, e.g., an automatic 3D scanner that uses a robot arm and one that uses an automatic rotary table. Specifically, these scanners are used to obtain a 3D shape using automatic assisting devices. Most of these scanners are required to perform numerous operations, such as merging, aligning, trimming, and filling holes. We are interested in developing an automatic 3D shape collection device using a spherical-coordinate-based guiding system. Then, the aim of the present study is to design an automatic guiding system that can automatically collect 3D shape data. We develop a 3D model of this system and measuring data which are collected by a personal computer. An optimal design of this system and the geometrical accuracy of the measured data are both evaluated using 3D modeling software. The developed system is then applied to an object having a highly complex shape and manifold sections. Our simulation results demonstrate that the developed system collects higher-quality 3D data than the conventional method.