• Journal of Welding and Joining
• /
• v.16 no.3
• /
• pp.55-63
• /
• 1998

Among the position sensing methods available, the arc sensor which utilizes the electrical signal obtained from the welding arc itself is one of the most prevalently used methods, because it has an advantage that no particular sensing device is necessary and real-time sensing of a groove position is possible directly under the arc. The authors have already developed a seam tracking system that contains a new arc sensor algorithm, which uses the relative welding current variation according to the tip-to-workpiece distance in GMA welding. In this study a torch height control algorithm for automatic weld seam tracking was proposed for completing the previous system, which uses an on-off control technique. To implement the torch height control algorithm during weld seam tracking the system parameters which include 2nd averaging range, weighting factor for 2nd moving averaging, and Z-directional basic compensation distance were determined by experimental analysis. Finally the two different height control methods, one is simple on-off control and the other on-off control using a reference current value , were compared in their tracking abilities.

• Journal of Biosystems Engineering
• /
• v.14 no.2
• /
• pp.85-93
• /
• 1989

This study was intended to develop the system which controls header height of combine automatically by means of sensing the difference between the header and the ground surface. A micro-computer was used for the controller. The sensing unit designed for the study was composed of potentiometer, oscillating link, and gage wheel. An electric-hydraulic circuit was driven by microcomputer to control header height of combine. Performance of the control system was tested by computer simulation, stationary operation of header, and traveling on the simulated ground.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.3 no.4
• /
• pp.472-480
• /
• 2014

The In solar power system, the height and azimuth of the sun are important parameters which control generated power magnitude. The tracking method that controls the daily generation magnitude according to latitude and longitude using the two axles is often used in the existing sunlight tracking system today. In this two-axle PV track control system, the self-load is concentrated on one FRAME. It is influenced of the regular load, snow load and the wind load, etc. It is difficult to set up the system in the conventional building. This research is a development about the small-scale economy track device of independent load-dispersing solar generation system. The position tracking algorithm is through new coordinates transformation calculating the height and azimuth of the sun.

• Journal of Biosystems Engineering
• /
• v.14 no.2
• /
• pp.94-103
• /
• 1989

This study was intended to develop the automatic feeding depth control system of the head-feed combine which could feed the rice head into threshing unit at the optimal depth regardless of plant height and uneven ground surface. In the control system, one-board microcomputer was used for the controller instead of conventional electric circuits. Field test of the combine equipped with the control system was conducted to evaluate its overall performance. It was also investigated how the location and time delay of rice head sensor affect the system performance.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.1095-1096
• /
• 2008

By adding height compensation to the usual 3 points skew adjustment device, an improved functional skew adjustment device is implemented in this paper. The proposed skew adjustment device is for traverse which will be adapted to BD and HD player system requiring more accuracy. and It can adjust not only R/T skew but also height. The system is composed of personal computer, control box, kinematic mechanism device and bar-code reader device. Application programs are implemented by visual basic.

• Korean Journal of Plant Resources
• /
• v.34 no.6
• /
• pp.608-615
• /
• 2021

Soil moisture control system including soil sensing and automatic water supply chain was constructed on open farmland and pot conditions. Soil moisture was controlled by the system showing over the soil moisture contents except 40% treatment. EC was gradually decreased by increasing cultivation days. On applying this system to control soil moisture, the growth and development characters of the bellflower were improved compared with control, cultivation without the automatic irrigation. Of the growth and development characters, plant height with water treatments was higher than that of control in 1st-year plants. Moreover, numbers of branch were increased by the increased soil moisture on farmland and pot condition. Capsule numbers for seed were best at 20%, 30% soil moisture treatment in 1st-year plants, and 20% to 50% treatment in 2nd-year plants. The construction of automatic soil moisture control system provide fundamental data for plant growth and development on open farmland soil condition.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.25 no.6
• /
• pp.536-541
• /
• 2015

In this paper, we propose a the image-based automatic flight control system for the mini drone. Automatic flight system with a camera on the ceiling and markers on the floor and landing position is designed in an indoor environment. Images from the ceiling camera is used not only to recognize the makers and landing position but also to track the drone motion. PC sever identifies the location of the drone and sends control commands to the mini drone. Flight controller of the mini drone is designed using state-machine algorithm, PID control and way-point position control method. From the, The proposed automatic flight control system is verified through the experiments of the mini drone. We see that known makers in environment are recognized and the drone can follows the trajectories with the specific ㄱ, ㄷ and ㅁ shapes. Also, experimental results show that the drone can approach and correctly land on the target positions which are set at different height.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.2
• /
• pp.22-28
• /
• 2019

In this study, we describe the mechanical design of the cylindrical workpiece inspection system which that can inspect the workpiece machined in the CNC lathe. The workpiece automatic measuring device is composed of a workpiece aligning mechanism, a workpiece diameter measuring mechanism, and a workpiece height measuring mechanism. If the workpiece machined on the CNC lathe is placed on the pedestal of the cylindrical workpiece inspection system, the workpiece aligning mechanism moves the workpiece to the diameter-measuring position and the height- measuring positions, and the diameter-measuring mechanism and the height- measuring mechanisms sequentially measure the diameter and the height of the workpiece. The cylindrical workpiece inspection system was designed and manufactured. The characteristic experiment was conducted to confirm the operation of the machine tool of the cylindrical workpiece inspection system. As a The result of the characteristic test shows that, the workpiece automatic measuring device operated safely.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.11
• /
• pp.932-936
• /
• 2016

In this paper, we present a method for the inspection of diamond wheels. In total, six items, including height, radius, and angle, need to be checked during the manufacturing of a diamond wheel. Automatic inspection through image processing is presented in this paper. First, a contour corresponding to the boundary of the diamond wheel is extracted from an image. Next, control points are selected by processing the contour. Seven control points are detected and used for the computation of the required item. Detailed procedures for the computation of the height, radius, and angle using control points are presented in this paper. Experimental results show the feasibility of the presented method.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.319-320
• /
• 2006

In this paper, automatic sunvisor system is introduced for driver's safety and convenience. This system has the mechanism which keeps the sun off without obstruction of driver's sight. The mechanism can make the sunvisor move forward or rotate left while remaining inside inner roof. The control system consists of a CPU, a motor driver, light sensors, and the algorithm that can control the movement of sunvisor efficiently. When the light sensors take the sun light, they give the signal to the CPU and the CPU calculates the best position of the sunvisor with the information of driver's eyes height. Then, the CPU gives the signal to motors that can move the sunvisor.