• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.11 no.7
• /
• pp.253-260
• /
• 2001

A Study of interior noise reduction in the magelv train is presented. Tarin speed of interest is low such that aero-dynamic noise is negligible and power supply system is a dominant noise source. Based on the measurements of interior noise and acceleration levels during running and zero speed conditions, dominant noise sources are identified. After spectra characteristics of noise sources are investigated several noise reducing methods are studied such as STL increasement of floor panels. sealing. and absorption treatment It is found that the most important noise sources are VVVF inverter and SLM in running condition, whereas air conditioner and DC/DC converter are dominant in zero speed. Sine the major noise sources are under the floor complete sealing and high STL of the floor panel are shown to be the most crucial factors in noise reduction After sound absorbing material, which is polyurethan foam of 50 mm thickness, is thickness, is attached to the downward side of the floor in addition to sealing treatment, the interior noise is reduced by 3~4 dB.

• Asian Journal of Atmospheric Environment
• /
• v.4 no.2
• /
• pp.63-71
• /
• 2010

The removal characteristics for aromatic and aliphatic VOCs by electron beam (EB) were discussed in terms of several removal variables such as initial VOC concentration, absorbed dose, background gas, moisture content, reactor material and inlet temperature. It was reviewed that only reactor material was an independent variable among the potential control factors concerned. It was also suggested that main mechanism by EB should be radical reaction for the VOC removal rather than that by primary electrons. It was discussed that the removal efficiency of benzene was lower than that of hexane due to a closed benzene ring. In the case of aromatic VOCs, it was observed that the decomposition of the VOCs with more functional groups attached on the benzene ring was much easier than those with less ones. As for aliphatic VOCs, it was also implied that the longer carbon chain was, the higher the removal efficiency became. An EB-catalyst hybrid system was discussed as an alternative way to remove VOCs more effectively than EB-only system due to much less by-products. This hybrid included supporting materials such as cordierite, Y-zeolite, and $\gamma$-alumina.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.9
• /
• pp.833-839
• /
• 2005

This work describes the effect of the number of roll pressing and the composition of carbon black on the electric and mechanical properties of carbon-PTFE electrode, in which composition is MSP20 : carbon black : $PTFE\;=\;95-X\;:\;X\;:\;5wt.\%$. It was found that the best electric and mechanical properties were obtained for sheet electrode roll pressed about 15 times and for sheet electrode, in which composition is MSP20 : carton black $PTFE\;=\;80\;:\;15\;:\;5wt.\%$. These behaviors could be explained by the network structure of PTFE fibrils and conducting Paths linked with carbon blacks, respectively. On the other hand, cell capacitor using the sheet electrode with $15wt.\%$ of carbon black attached on aluminum current collector with the electric conductive adhesive, in composition is carbon black $CMC\;=\;70\;:\;30wt.\%$, has exhibited the best rate capability between $0.5\;mA/cm^2\~100\;mA/cm^2$ current density and the lowest ESR.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.343-346
• /
• 1998

The generation of pretilt angle in nematic liquid crystal (NLC) and electro-optical (EO) characteristics of photo-aligned twisted nematic (TN)-LCD with oblique P-polarized ultraviolet (UV) light irradiation on the two kinds of the soluble polyimide (PI) surfaces containing trifluoromethyl moieties were investigated. The generated pretilt angle of NLC is about 2.5$^{\circ}$with P-polarized UV light irradiation of 20$^{\circ}$on PI-3 surface at 20 min.; However pretilt angle of about 0.5$^{\circ}$are observed on PI-1 and PI-2 surfaces. The generated pretilt angle of NLC on PI-3 surface may be attributed to the trifluoromethyl moieties attached to the lateral benzene rings. The voltage-transmittance and response time characteristics of photo-aligned TN-LCD with P-polarized UV light irradiation of 20$^{\circ}$on PI-1 surface at 20 min were almost same in comparison with the rubbing-aligned TN-LCD. However, the high threshold voltage and slow response are observed on PI-3 surface. Also, the decay time $\tau$$\sub$d/ of photo-aligned TN-LCD is attributed to the anchoring energy of NLC.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.05b
• /
• pp.34-37
• /
• 2001

As the integrated circuit device shrinks to smaller dimensions, chemical mechanical polishing (CMP) process was required for the global planarization of inter-metal dielectric (IMD) layer with free-defect. However, as the inter-metal dielectrics (IMD) layer gets thinner, micro-scratches are becoming as major defects. Micro-scratches are generated by agglomerated slurry, solidified and attached slurry in pipe line of slurry supply system. To prevent agglomerated slurry particle from inflow, we installed 0.5${\mu}m$ POU (point of use) filter, which is depth-type filter and has 80% filtering efficiency for the $1.0{\mu}m$ size particle. In this paper, we studied the relationship between defect generation and pad count to understand the exact efficiency of the slurry filtration, and to find out the appropriate pad usage. Our preliminary results showed that it is impossible to prevent defect-causing particles perfectly through the depth-type filter. Thus, we suggest that it is necessary to optimize the flow rate of slurry to overcome depth type filters weak-point, and to install the high spray of de-ionized Water (DIW) with high pressure.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.355-356
• /
• 2006

This work describes the effect of the number of roll pressing and the composition of carbon black on the electric and mechanical properties of carbon-PTFE electrode, in which composition is MSP20 : carbon black: PTFE = 95-X : X : 5 wt.%. It was found that the best electric and mechanical properties were obtained for sheet electrode roll pressed about 15 times and for sheet electrode, in which composition is MSP20 carbon black : PTFE = 80 : 15 : 5 wt%. These behaviors could be explained by the network structure of PTFE fibrils and conducting paths linked with carbon blacks, respectively. On the other hand, cell capacitor using the sheet electrode with 15 wt.% of carbon black attached on aluminum current collector with the electric conductive adhesive, in composition is carbon black : CMC = 70 : 30 wt.%, has exhibited the best rate capability between 0.5 $mA/cm^2$ ~ 100 $mA/cm^2$ current density and the lowest ESR.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.1
• /
• pp.85-89
• /
• 2008

An objective of this paper is to develop a partial discharge (PD) measurement device for monitoring gas insulated switches installed in power distribution system. A capacitive voltage probe was studied and designed to detect PD pulse without an electrical connection. The PD measurement device consists of the capacitive voltage probe attached outside of a bushing, a coupling network which attenuates AC voltage by 270 dB, and a low noise amplifier with the gain of 40 dB in ranges of 500 kHz${\sim}$20 MHz. The sensitivity of the prototype device calculated by a calibrator was 1.98 m V /pc. An application experiment was carried out in a 25.8 kV gas insulated switch and the peak pulse of 76.7 pC was detected. From the experimental results, it is expected that the PD measurement device can be applied to online monitoring system of gas insulated switches.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.17 no.3
• /
• pp.207-224
• /
• 2015

Protective clothing for riot policewomen is worn by policewomen to protect their body at suppressing a riot. Plastic guards of Nylon 66 material are attached to the base of E.V.A. Foam material. Protective clothing for riot policewomen consists of a jacket, guards for arms and legs, upper arm braces, and thigh pads. This study was aimed to develop the base pattern of the jacket to protect the torso and to improve the body suitability and the adaptability to movements of protective clothing for riot policewomen. Since current protective clothing worn by riot policewomen is manufactured with the same design of protective clothing for riot policemen, the body suitability and the adaptability to movements are not very satisfactory for policewomen who has different body structure than from riot policemen. Therefore, the purpose of this study is to reflect the body size and characteristics of riot policewomen and develop the base pattern of protective clothing with better body suitability and adaptability to movements. In this respect, amount and place of dots on the jacket were differently designed, made and evaluated by fitting test. The base with the best evaluation was selected as the final experiment clothing to demonstrate its superiority compared with the existing protective clothing.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.22 no.3
• /
• pp.33-47
• /
• 2020

As people have gained leisure time and become more interested in sports, various industries catering to these sports, including aquatic and underwater activities are growing. Many people are getting into scuba diving, where people can explore the sea at depths of more than 40-meters. Despite the increasing demand, there are limited studies on the sport. This study aims to provide basic research on materials suitable for developing technical scuba diving suits by analyzing several areas, such as design, material, sewing patterns, etc. The following trends were observed in all wetsuits: closure designs, ergonomic patterns, practical and functional details. Neoprene was the primary material of diving suits, and various functional materials were attached to the outer fabric or lining. The seam technique which minimized water contact and improved durability was sewing. Various techniques were also applied, such as flatlock stitching, GBS, LFS, etc. Subsequent studies shall investigate consumer preference etc. and other aspects, and continue to allow for the research and development of technical diving suits.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.1 no.1
• /
• pp.114-127
• /
• 1998

A user friendly computer code(EMCOMST; Electro-Magnetic response for COMposite STructures) was developed which provides with computations of the response characteristics such as reflectance and transmittance to the incident wave angles, frequencies, composite thicknesses, ply orientations, and types of backplate as the linearly polarized transverse electro-magnetic wave is emitted to the advanced composite structures. In this investigation were reviewed the electromagnetic characteristics of the continuous orthotropic fiber-reinforced organic matrix composites with or without ferrite fillers, which are actively applied to low-weight and high-strength aircraft structures. Also were calculated the response of the three layered compound structures which have appropriately stacked above-mentioned materials as transmitting layer, absorbing layer, reflection layer, respectively under the specific thickness constraints for mechanical strength design requirements. For the composite structures presented in this study, minimum reflectance value less than -5㏈ can be obtained in the frequency range of 4 to 12 ㎓. In addition, analysis of structures attached isotropic radar absorbing materials(RAM) is facilitated by putting the material properties in the material input card entries adequately.