• Korean Journal of Optics and Photonics
• /
• v.15 no.1
• /
• pp.1-5
• /
• 2004

Tunable diode laser absorption spectroscopy was performed for analysis of the H$_2$$^{18}$ O/H$_2$$^{16}$ O isotope ratio of a water sample which was enriched by the membrane distillation method. In order to improve the signal-to-noise ratio, the wavelength modulation spectroscopic method was used with a lock-in amplifier. The fringe noise could be suppressed by using the FFT (Fast Fourier Transform) lowpass filter and the optimization of the modulation depth of the laser frequency. The maximum deviation of $\delta$-value was measured to be$\pm$4$\textperthousand$.

• Nuclear Engineering and Technology
• /
• v.52 no.10
• /
• pp.2299-2305
• /
• 2020

Zr alloy specimens were coated with Cr-Al alloy to enhance their resistance to oxidation. The coated samples were oxidized at 1200 ℃ in a steam environment for 300 s and showed extremely low oxidation when compared to uncoated Zr alloy specimens. The microstructure and elemental distribution of the oxides formed on the surface of Cr-Al alloys have been investigated by transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). A very thin protective layer of Cr₂O₃ formed on the outer surface of the Cr-Al alloy, and a thin Al₂O₃ layer was also observed in the Cr-Al alloy matrix, near the surface. Our results suggest that these two oxide layers near the surface confers excellent oxidation resistance to the Cr-Al alloy. Even after exposure to a high temperature of 1200 ℃, inter-diffusion between the Cr-Al alloy and the Zr alloy occurred in very few regions near the interface. Analysis of the inter-diffusion layer by high-resolution transmission electron microscopy (HRTEM) and energy dispersive X-ray spectroscopy (EDS) measurement confirmed its identity as Cr₂Zr.

• Journal of Radiation Industry
• /
• v.4 no.4
• /
• pp.335-339
• /
• 2010

In this study, the surface of polyimide (PI) films was modified using ion implantation to enhance its adhesion to a deposited copper (Cu) layer. The surfaces of the PI films were implanted with 150 keV $Xe^+$ ions at fluences varying from $1{\times}10^{14}$ to $1{\time}10^{16}ions\;cm^{-2}$. The Cu layers were then deposited on the implanted PI. The surface properties of the implanted PI film were investigated based on the contact angle measurements, Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM). Furthermore, the adhesive strength between the deposited Cu layer and PI film was estimated through a scratch test using a nanoindenter. As a result, the surface environment of the PI film was changed by the ion implantation, which could have a significant effect on the adhesion between the deposited Cu layer and the PI.

• Bulletin of the Korean Chemical Society
• /
• v.27 no.9
• /
• pp.1393-1396
• /
• 2006

The 1+1 two-photon Resonant Enhanced Multiphoton Ionization (REMPI) spectra of 1,4-dichlorobenzene was obtained from 240 nm through to 250 nm on a laser mass spectrometer. Special care was taken to build up a heatable sample inlet system suitable for detecting a trace semi-volatile organic compound and reducing the memory effort on the inner wall of the inlet system. The detection limits of 1,4-dichlorobenzene in ppbV/V concentration range at certain wavelengths are presented.

• KSTLE International Journal
• /
• v.1 no.2
• /
• pp.69-75
• /
• 2000

The paper compares topography, phase contrast and force spectroscopy in atomic force microscopy data for evaluating the microheterogeneity of surface layer. The worn surface of ion-plated TiN coating was measured using both a laboratory-built and a commercial AFM. The results of analysis revealed structural and micromechanical heterogeneity of the worn surfaces. We demonstrated that the phase image allows relatively qualitative estimation of elastic modulus of the sample surface. The tribolayer formed in the worn surface possessed much lower stiffness than the original coating. It is shown that the most stable phase imaging is provided with a stiff cantilever. In this case, phase contrast is well conditioned, first of all, by microheterogeneity of elastic properties of the investigated surfaces. In this study an attempt was also made to correlate the results of phase imaging with that of the farce spectroscopy. The joint analysis of information on the surface properties obtained by the phase imaging and quantitative data measured with the force spectroscopy methods allows a better understanding of the nature of the surface micromechanical heterogeneity.

• Journal of the Korean Ceramic Society
• /
• v.39 no.5
• /
• pp.433-437
• /
• 2002

Impact-collision ion scattering spectroscopy was applied to study the geometrical structure of epitaxially grown TiO layers on the MgO(100) surface. Hetero-epitaxial TiO layer was formed by thermal evaporation of titanium onto the MgO(100) surface followed by the exposure to oxygen at $400{\circ}$. The well-ordered TiO structure was confirmed by the impact-collision ion scattering spectroscopy and reflection high energy electron diffraction patterns. It is revealed that the Ti and O atoms are located on the on-top site of the MgO(100) surface and the TiO overlayers are composed of little three dimensional islands.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.6
• /
• pp.625-631
• /
• 2015

The hardness of surface treated magnesium alloy was evaluated using laser induced breakdown spectroscopy. The surface of the specimen was hardened mechanically, and the hardness profiles were measured using a traditional measurement technique. A laser beam was irradiated to generate a plasma, and the peaks of the components of the specimen were analyzed. A wavelength of 333.66 nm and 293.65 nm were selected as the atomic and ionic peaks, respectively. The ratios of the ionic peak to the atomic peak were obtained so as to compare the hardness profile. As the depth increased, the ratio decreased. These results are in good agreement with the previous hardness measurement results. It can be considered that this technique could be applied for remote and time-efficient hardness measurement.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.2
• /
• pp.189-194
• /
• 2002

Two-photon resonant third photon ionization of atomic bromine $(4p^5\;^2P_{3/2}\;and\;^2P_{1/2})$ has been studied using a photoelectron imaging spectroscopy in the wavelength region 250 - 278 nm. The technique has yielded simultaneously both relative branching ratios to the three levels of $Br^+(^3P_2,\;^3P_{0.1}\;and^1D_2)$ with $4p^4$ configuration and the angular distributions of outgoing photoelectrons. The product branching ratios reveal a strong propensity to populate particular levels in many cases. Several pathways have been documented for selective formation of $Br^+(^3P_2)$ and $Br^+(^3P_{0.1})$ ions. In general, the final ion level distributions are dominated by the preservation of the ion core configuration of a resonant excited state. Some deviations from this simple picture are discussed in terms of the configuration interaction of resonant states and the autoionization in the continuum. The photoelectron angular distributions are qualitatively similar for all transitions, with a positive $A_2$ anisotropy coefficient of 1.0-2.0 and negligible $A_4$ in most cases, which suggests that the angular distribution is mainly determined by the single-photon ionization process of a resonant excited state induced from the third photon absorption.

• Korean Journal of Optics and Photonics
• /
• v.5 no.4
• /
• pp.461-465
• /
• 1994

The spatial flatness of dye jet depending on the Reynold's number has analyzed by using a Michelson interferometer. When the Reynold's number of dye jet was 600, the flatness of the flow was the best. Under this condition, the dye laser with Littman-type configuration has been operated in a single longitudinal mode at the pumping energy of 0.5~1.0 mJ/pulse. The conversion efficiency and beam divergence were 4.7% and 3 mrad, respectively. ively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.171-171
• /
• 1999

We studied the charge redistribution in the Pt-M (M=Cu, Co) alloys by X-ray Absorption Near Edge Spectroscopy(XANES) and X-ray Photoelectron Spectroscopy(XPS). These analysis tools provide us information about the charge transfer in the valence band of intermetallic bonding. The samples were prepared by arc-melting method. After annealing this samples in vacuum for several hours, we cold get the ordered samples, which were confirmed with XRD analysis. the core and valence level energy shift in these system were investigated by Mg $K\alpha$(1253.6eV) x-ray source for Pt-Co alloys and monochromatized Al $K\alpha$ (1486.6eV) for Pt-Cu alloys. Pt L2, L3-edge, and Cu, Co K-edge XANES spectra were measured with the total electron-yield mode detector at the 3Cl beam line of the PLS (Pohang light source0. from the changes of White line (WL) area and the core level shifts of the each metal sites, we can obtain the information about the electrons participating in the intermetallic bonding of the Pt-Cu and Pt-Co alloys.