• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.5 s.248
• /
• pp.397-404
• /
• 2006

Effects of surface defect distribution on flame instability during flame-surface interaction are experimentally investigated. To examine chemical quenching phenomenon which is caused by radical adsorption and recombination processes on the surface, thermally grown silicon oxide plates with well-defined defect density were prepared. ion implantation technique was used to control the number of defects, i.e. oxygen vacancies. In an attempt to preferentially remove oxygen atoms from silicon dioxide surface, argon ions with low energy level from 3keV to 5keV were irradiated at the incident angle of $60^{\circ}$. Compositional and structural modification of $SiO_2$ induced by low-energy $Ar^+$ ion irradiation has been characterized by Atomic Force Microscopy (AFM) and X-ray Photoelectron Spectroscopy (XPS). It has been found that as the ion energy is increased, the number of structural defect is also increased and non-stoichiometric condition of $SiO_x({\le}2)$ is enhanced.

• Bulletin of the Korean Chemical Society
• /
• v.19 no.5
• /
• pp.549-553
• /
• 1998

The structure and layer distribution of cadmium arachidate Langmuir-Blodgett film were analyzed by the small angle X-ray reflectivity measurements using synchrotron radiation. Y-to X type transition was ocurred during the 39th passage of deposition of cadmium arachidate. Based on the measurement of the consumed area of the monolayer, it was determined that about 27.5 layer was deposited. Using the synchrotron X-ray, the reflectivity profile of cadmium arachidate LB film over the wide range of grazing angle was obtained. The X-ray reflectivity profile was analyzed using the recursion formula. By fitting the location and dispersion of the subsidiary maxima between the Bragg peaks of the measured reflectivity profile with that of the calculated reflectivity profile, the average thickness and the distribution of layer thickness were evaluated. The genetic algorithm was adopted to the fitting of reflectivity profile to evaluate the optimum value of the number distribution of layer. Based on the morphology measurement with an atomic force microscopy (AFM), the domain structure and mean roughness of LB films were obtained. The mean roughness value calculated based on the number of layer distribution obtained from the measurement by AFM is consistent with that obtained from X-ray reflectivity analysis.

• Composites Research
• /
• v.34 no.6
• /
• pp.373-379
• /
• 2021

A series of novel PBI/SrTiO₃ nanocomposite membranes composed of polybenzimidazole (PBI) and strontium titanate (SrTiO₃) with a perovskite structure were fabricated with various concentrations of SrTiO₃ through a solution casting method. Various characterization techniques such as proton nuclear magnetic resonance, thermogravimetric analysis, atomic force microscopy (AFM) and AC impedance spectroscopy were used to investigate the chemical structure, thermal, phosphate absorption and morphological properties, and proton conductivity of the fabricated nanocomposite membranes. The optimized PBI/SrTiO₃-8 polymer nanocomposite membrane containing 8wt% of SrTiO₃ showed a higher proton conductivity of 7.95 × 10^-2 S/cm at 160℃ compared to other nanocomposite membranes. The PBI/SrTiO₃-8 composite membrane also showed higher thermal stability compared to pristine PBI. In addition, the roughness change of the polymer composite membrane was also investigated by AFM. Based on these results, nanocomposite membranes based on perovskite structures are expected to be considered as potential candidates for high-temperature PEM fuel cell applications.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.27-28
• /
• 2021

The search for new corrosion inhibitors for different corrosive mediums is a never-ending task. In the present work, the corrosion inhibition behavior and adsorption mechanism of two novel synthetic thiazolidinedione derivatives noted MTZD and ATZD in 3.5 wt.% NaCl solution on copper were investigated. Electrochemical, scanning electron microscope (SEM), atomic force microscopy (AFM) techniques were used along with first-principles DFT calculations. At maximum inhibitor concentration i.e., 300 ppm corrosion inhibition efficiency reached maximum up to 90% and 96% for MTZD and ATZD, respectively, and thereby followed the order of ATZD > MTZD. The inhibition efficiency increased up to 24 h of immersion, and then decreased after 48h immersion. The potentiodynamic curves suggested that the inhibition action of tested compounds is a mixed type of inhibitor. The first-principles DFT calculations suggested that compounds under investigation formed covalent bonds with Cu(111) surface via reactive sites. SEM and AFM results confirmed the formation of protective barrier that prevent corrosion attack.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.81-81
• /
• 2011

Sol-gel spin-coating법을 이용하여 ZnO 박막을 증착하였다. Sol 전구체 용액을 Si(100) 기판에 증착하고 전열처리(pre-heat treatment)하여 gel 상태의 ZnO 박막을 형성시킨 후 다른 속도로 냉각시켰다. Atomic force microscopy (AFM), X-ray diffraction (XRD), Raman, photoluminescence (PL)을 이용하여 냉각속도가 ZnO 박막의 구조적 및 광학적 특성에 미치는 영향을 분석하였다. 느린 속도($5^{\circ}C$/min)로 냉각시킨 ZnO 박막은 나노섬유질구조(nano-fibrous structure)를 나타내었고, 상온에서 바로 냉각시킨 ZnO 박막은 매우 매끄러운 표면(mirror-like surface)을 나타내었다. ZnO (100), ZnO (002), ZnO (101) 방향을 나타내는 회절피크가 관찰되었고, 냉각속도에 따른 ZnO 박막의 배향성을 알아보기 위하여 texture coefficient (TC)를 계산해 보았다. 상온에서 바로 냉각시킨 ZnO 박막(TC(002)=76.3%)이 느린 속도로 냉각시킨 박막(TC(002)=45.2%)보다 (002) 방향으로의 배향성이 우세하게 나타났으며, 잔류응력도 작았다. 뿐만 아니라 PL을 이용한 광학적 특성평가에서도 상온에서 바로 냉각시킨 ZnO 박막에서 더 강한 강도와 좁은 반치폭(full-width at halt-maximum)을 갖는 near-band-edge emission (NBE) 피크가 관찰되었다. 후열처리에 따른 구조적 및 광학적 특성 변화 또한 연구하였다.

• Korean Journal of Materials Research
• /
• v.21 no.10
• /
• pp.525-531
• /
• 2011

Two dimensional (2D) arrays of noble metal nanoparticles are widely used in the sensing of nanoscale biological and chemical events. Research in this area has sparked considerable interest in many fields owing to the novel optical properties, e.g., the localized surface plasmon resonance, of these metallic nanoarrays. In this paper, we report successes in fabricating 2D arrays of gold nano-islands using nanosphere lithography. The reproducibility and the effectiveness of the nano-patterning method are tested by means of spin coating and capillary force deposition. We found that the capillary force deposition method was more effective for nanospheres with diameters greater than 600 nm, whereas the spin coating method works better for nanospheres with diameters less than 600 nm. The optimal deposition parameters for both methods were reported, showing about 80% reproducibility. In addition, we characterize gold nano-island arrays both geometrically with AFM as well as optically with UV-VIS spectrometry. The AFM images revealed that the obtained nano-arrays formed a hexagonal pattern of truncated tetrahedron nano-islands. The experimental and theoretical values of the geometric parameters were compared. The 2D gold nano-arrays showed strong LSPR in the absorption spectra. As the nano-islands increased in size, the LSPR absorption bands became red-shifted. Linear dependence of the plasmon absorption maximum on the size of the gold nano-islands was identified through the increment in the plasmon absorption maximum rate for a one nanometer increase in the characteristic length of the nano-islands. We found that the 2D gold nano-arrays showed nearly seven-fold higher sensitivity of the absorption spectrum to the size of the nano-islands as compared to colloidal gold nano-particles.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1570-1572
• /
• 2004

OLED(organic light-emitting diode)소자에 사용되는 ITO(Indium-tin oxide)전극에 Ar/$O_3$ 플라즈마 표면처리 함으로써 ITO전극에 표면상태의 개선에 좋은 영향을 미치는 것으로 나타났다. 13.56MHZ RF 플라즈마 장치를 이용하여 Ar/$O_3$ 플라즈마 처리한 후 AFM(atomic force microscopy)측정을 통해 표면 morphologyjroughless를 분석하고, XPS(X-Ray Photoelectron Spectroscopy)분석을 통해 표면의 화학적 조성비 분석을 수행 하였다.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.43-44
• /
• 2002

Langmuir-Blodgett mono- and multilayer films from 2,4-heneicosanedione have been examined as lubrication coatings In the process of wear. Tribological properties of the films have been studied by atomic force microscopy and microtribometer. It has been observed that the wear resistance of silicon surface coated with OTS/LB multilayer system increased by several orders of magnitude compared to uncoated surfaces at low normal load. The results obtained suggest that the system constructed on silicon surface reduces surface energy, friction coefficient and increases life of substrate due to a possibility of LB film self-repairing during frictional contact.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.2
• /
• pp.397-400
• /
• 2010

Zirconium oxide thin films deposited on the p-type Si(100) substrates by radio-frequency (RF) reactive magnetron sputtering with different plasma gas ratios have been studied by using spectroscopic ellipsometry (SE), atomic force microscopy (AFM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The deposition of the films was monitored by the oxygen gas ratio which has been increased from 0 to 80%. We found that the thickness and roughness of the zirconium oxide thin films are relatively constant. The XRD revealed that the deposited thin films have polycrystalline phases, Zr(101) and monoclinic $ZrO_2$ ($\bar{1}31$). The XPS result showed that the oxidation states of zirconium suboxides were changed to zirconia form with increasing $O_2$ gas ratio.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.1
• /
• pp.21-24
• /
• 2020

We investigated a solution-driven Yttrium Tin Oxide (YSnO) film that was imprinted using a parallel nanostructure as a liquid crystal (LC) alignment layer. The imprinting process was conducted at the annealing temperature of 100℃. To evaluate the effect of this process, we conducted surface analyses including atomic force microscopy (AFM). During imprinting, the surface roughness was reduced, and anisotropic characteristics were observed. Planar LC alignment was observed at a pretilt angle of 0.22° on YSnO film. Surface anisotropy induced by imprinting method forces LC to align along the direction of the parallel nanostructure, which is an alternative to conventional polyimide treated using a rubbing process.