• Journal of Korean Society for Atmospheric Environment
• /
• v.19 no.E1
• /
• pp.1-9
• /
• 2003

The soil concentrations of polychlorinated biphenyls (PCBs) were measured at 12 sites in Ansung, Kyonggi province, Korea. Correlation coefficient (r) between total PCBs and organic matter content (OM) was significant (r=0.562, p< 0.05). It suggests that organic matter may be a key factor of soil absorption of PCBs. The PCB concentrations of low chlorinated congeners with high vapor pressure were relatively abundant in air but high chlorinated congeners with low vapor pressure were mainly dominated by soil. The results indicated the influence of physicochemical properties of PCBs such as vapor pressure, octanol - air partition coefficient ( $K_{OA}$ ). The calculated soil/air fugacity quotients suggested that the soil may be a source of heavier molecular PCBs (>penta-CBs) to the atmosphere, where lighter molecular PCBs appear to be affected by a movement from air to soil, especially tetra-CBs. Therefore, PCB homologs with low vapor pressure might have been influenced by revolatilization from soil.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.421-422
• /
• 2002

The purpose of this paper is to investigate the leakage characteristics of the valve stem in the gasoline engines. Especially, three factors affecting oil leakage are the power cylinder, engine head system, and the positive crankcase ventilation system. Which is the most variables, analysis difficulty is the valve stem seal characteristics. The testing system is used with oil motoring system. The leakage of an engine is analyzed for the cylinder temperature, atmosphere pressure, positive pressure, negative pressure, revolution of the camshaft and the surface roughness of the valve stem.

• Journal of computational fluids engineering
• /
• v.10 no.4 s.31
• /
• pp.59-65
• /
• 2005

A numerical analysis was made to investigate the simple silencer for high pressure blast flow fields. Reynolds-Averaged Navier-Stokes equations were solved for an axisymmetric computational domain constructed by multi block grids. A blast flow field without the silencer was also calculated to validate the present numerical method. The effect of pressure diminution for the silencer was calculated by comparing with and without silencer at the atmosphere region. It was found that the tested silencer could achieve 89.4 percent pressure diminution.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.131-134
• /
• 2007

This numerical analysis was performed in order to validate adoption of the sheet breakup model in high-pressure environment, which were used for prediction of spray characteristics in atmosphere environment. In experiments the higher environment pressure the shorter breakup length; the results of new sheet breakup model predicted the breakup length in good agreement with experimental results qualitatively and quantitatively. Also the shape of spray calculated by numerical analysis were agreed well with experiments quantitatively.

• Journal of the Korean Ceramic Society
• /
• v.33 no.1
• /
• pp.41-48
• /
• 1996

Self-propagating High-temperature Synthesis of Ti+N system has been investigated using the cylindrical high pressure reactor. The nitrogen pressure was varied from 40 to 80 atmosphere and TiNx(x=0.55) powder produced by SHS process was used as a diluent in order to control the reaction. Both the velocity of surface reaction and the ratio of TiN synthesis increased with increasing the nitrogen pressure. As the amount of diluent increases the degree of conversion to titanium nitride increases. Homogenious TiN powder was obtained in the composition 50Ti+50TiN0.94(diluent)

• Journal of the Korean Society of Safety
• /
• v.16 no.4
• /
• pp.109-114
• /
• 2001

Explosive characteristics of the city gas were determined by using the gas explosion apparatues. The explosive range is determined between lower explosive limit of 5.0% and upper explosive limit of 15.3% at atmosphere and even though the oxygen concentration is decreased, lower explosive limit is not changed, but upper explosive limit is rapidly decreased. The minimum oxygen for combustion is determined 10%. The maximum explosion pressure is determined 5.72$\textrm{cm}^2$ and the maximum rate of explosion pressure rise is oxygen concentration of 12% to determined 160.12$\textrm{cm}^2{\cdot}$sec.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.888-891
• /
• 2003

This paper describes on the fabrication and characteristics of micro ceramic thin-film type pressure sensors based on Ta-N strain-gauges for high-temperature applications. The Ta-N thin-film strain-gauges are deposited onto thermally oxidized Si diaphragms by RF sputtering in an argon-nitrogen atmosphere($N_2$ gas ratio: 8 %, annealing condition: $900^{\circ}C$, 1 hr.), Patterned on a wheatstone bridge configuration, and use as pressure sensing elements with a high stability and a high gauge factor. The sensitivity is $1.097{\sim}1.21mV/V.kgf/cm^2$ in the temperature range of $25{\sim}200^{\circ}C$ and the maximum non-linearity is 0.43 %FS. The fabricated pressure sensor presents a lower TCR, non-linearity than existing Si piezoresistive pressure sensors. The fabricated micro ceramic thin-film type pressure sensor is expected to be usefully applied as pressure and load sensors that is operable under high-temperature environments.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.4
• /
• pp.132-138
• /
• 2007

Experimental results of pulsating pressure behavior inside a chamber have been confirmed by computational work. Inside-cylinder pressure shows unstable condition at low rpm. This is caused by plate-type suction valve. It has effect up to inlet of the chamber. But trembling phenomenon is reduced as the pressure is enlarged by increasing the rpm. Result comparison between experimental and numerical analysis shows pulsation reduction is affected by the chamber. We can confirm that compressible effect of the working flow is shown at chamber inlet by increasing rpm. On the other side, this effect is declined at chamber outlet by increasing rpm. It means outlet pressure is going on balance with atmosphere pressure. Buffer plate-type chamber has efficiency of pulsation flow reduction.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1449-1450
• /
• 2011

The SiC-$ZrB_2$ composites were produced by subjecting a 40:60 (vol.%) mixture of zirconium diboride($ZrB_2$) powder and ${\beta}$-silicon carbide (SiC) matrix to spark plasma sintering(SPS) under argon atmosphere at 50MPa(P50) and 60MPa(P60) pressure. The relative density, 94.13% of P60 sample was lower than that, 94.75% of P50 sample. Reactions between ${\beta}$-SiC and $ZrB_2$ were not observed via x-ray diffraction (hereafter, XRD) analysis. The trend of flexural strength of SiC-$ZrB_2$ composites were in accordance with the relative density. The properties of a SiC-$ZrB_2$ composites through SPS under argon atmosphere were positive temperature coefficient resistance in the temperature range from $25^{\circ}C$ to $500^{\circ}C$, and electrical resistivity of P50 and P60 sample were $6.75{\times}10^{-4}$ and $7.22{\times}10^{-4}{\Omega}{\cdot}cm$ at room temperature, respectively.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.11
• /
• pp.832-840
• /
• 2008

Ablation occurs at irradiance beyond $10^9\;W/cm^2$ with nanosecond and short laser pulses focused onto any materials. Phenomenologically, the surface temperature is instantaneously heated past its vaporization temperature. Before the surface layer is able to vaporize, underlying material will reach its vaporization temperature. Temperature and pressure of the underlying material are raised beyond their critical values, causing the surface to explode. The pressure over the irradiated surface from the recoil of vaporized material can be as high as $10^5\;MPa$. The interaction of high power nanosecond laser with a thin metal in air has been investigated. The nanosecond pulse laser beam in atmosphere generates intensive explosions of the materials. The explosive ejection of materials make the surrounding gas compressed, which form a shock wave that travels at several thousand meters per second. To understand the laser ablation mechanism including the heating and ionization of the metal after lasing, the temporal evolution of shock waves is captured on an ICCD camera through laser flash shadowgraphy. The expansion of shock wave in atmosphere was found to agree with the Sedov's self-similar spherical blast wave solution.