• Journal of agriculture & life science
• /
• v.51 no.6
• /
• pp.89-105
• /
• 2017

This study utilized 32,312 records of 17 linear type and 10 conformation traits(including final scores) of Hanwoo cows in the KAIA(Korea Animal Improvement Association) ('09~'10), with 60,556 animals in the pedigree file. Traits included stature, body length, strength, body depth, angularity, shank thickness, rump angle, rump length, pin bone width, thigh thickness, udder volume, teat length, teat placement, foot angle, hock angle, rear leg back view, body balance, breed characteristic, head development, forequarter quality, back line, rump, thigh development, udder development, leg line, and final score. Genetic and residual(co) variances were estimated using bi-trait pairwise analyses with EM-REML algorithm. Herd-year-classifier, year at classification, and calving stage were considered as fixed effects with classification months as a covariate. The heritability estimates ranged from 0.03(teat placement) to 0.42(body length). Rump length had the highest positive genetic correlation with pin bone width(0.96). Moreover, stature, body length, strength, and body depth had the highest positive genetic correlations with rump length, pin bone width, and thigh thickness(0.81-0.94). Stature, body length, strength, body depth, rump length, pin bone width, and thigh thickness traits also had high positive genetic correlations.

• Journal of environmental and Sanitary engineering
• /
• v.16 no.3
• /
• pp.96-103
• /
• 2001

This study was carried out to investigate the major factors for the removal of NOMs (Natural Organic Matters) by alum ferric chloride and blended coagulants that consisted of alum and ferric chloride. Investigated factors were pH, the dosage of coagulant, alkalinity, hardness and bloc strength. The particle size contained in the test water came from the Han River was also measured. DOC(Dissolved Organic Carbon) removal at pH 6 was two to three times higher than at pH 8.5. The blended coagulant showed 9 to 10 percent higher DOC removal efficiency and 2 to 4 percent higher turbidity under the same condition. Alkalinity consumption of alum, ferric chloride and blended coagulant was 81%, 90% and 86% of theoretical value, respectively. The limit concentration of alkalinity to avoid pin floe was 10 mg $CaCO_3/L$ when alum was used. Hardness had no apparent effect on coagulation. The residual turbidity and $UV_{254}$ showed a tendency of increasing with floc strength($sec^{-1}$) increase. The order of floe strength was the following; alum >blended coagulant > ferric chloride. The particle counter test showed 89 percent of the small particle size(SPS, $1~5{\;}{\mu}textrm{m}$) and 11 percent of the medium to large particle size(M.LPS, $5~125{\;}{\mu}textrm{m}$). At PH7.85, the particle removal efficiencies of SPS($1~5{\;}{\mu}textrm{m}$) and M.LPS($5~125{\;}{\mu}textrm{m}$) in the coagulation process were 81% and 95%, respectively.

• The Korean Journal of Mycology
• /
• v.26 no.4 s.87
• /
• pp.531-537
• /
• 1998

Forest green mold incidence rate, extent of damage according to the inoculation periods, and its cultural characteristics were observed in the automatic cultural system of the winter mushroom, Flammulina velutipes. The incidence rate of the forest green mold was 7.7% in early cultivation stage and slowly increased to 14.9% in harvest stage. When the forest green mold was inoculated at cultural period, the rate was recorded at 100%, but the extent of the damage increased up to 40% (+++). There was also 100% incidence rate at early pinheading time, whereas the yield of mushroom decreased to ++ $(10{\sim}39%)$. The rate of forest green mold was greatly decreased to 34.4% at 10 days after pinheading, and its damage extent was also below 10%. A pathogen to infect the winter mushroom was identified as Trichoderma pseudokoningii. It's optimum temperature for mycelial growth is $25^{\circ}C$, and it grew 2.6 times faster than that of F. velutipes. The mycelial color of T. pseudokoningii was pale yellow or olivaceous in shades on PDA medium. Phialospore was one celled, and ellipsodal or obovoid, smooth walled, and measured $1.3{\sim}3.0{\times}1.0{\sim}2.5\;{\mu}m$. It aggregated in small heads at the tips of the phialides. The phialides were $3.2{\sim}9.2{\times}2.0{\sim}5.5\;{\mu}m$ and were of bowling pin type, solitary and alternate or more irregularly disposed at the conidiophore apex, T. pseudokoningii depressed the F. velutipes growth at the crossing cultivation when they were simultaneously. FV 4-1 (F. velutipes) cultivar was less depressed by T. pseudokoningii, but had a lower cross growth rate than the other four cultivars.

• Journal of Korea Foundry Society
• /
• v.20 no.4
• /
• pp.230-239
• /
• 2000

High pressure wear characteristics of DCI(Ductile Cast Iron) were investigated through unlubricated pin-on-disc wear test. Wear test were carried out at speed of 23m/min, under pressure of 3MPa and 3.3 MPa. Cu and/or Mn were added to examine the effect of alloying elements on the high pressure wear characteristics of DCI. To investigate the relationship between wear characteristics and mechanical properties of DCI, Brinell hardness and V-notched Charpy impact energy were tested. Wear surface of each specimen was observed by SEM to determine the wear mechanism of DCI under high pressure wear condition. In the mild wear region, wear characteristics of alloyed DCI specimens were very similar to that of unalloyed DCI. But mild-severe wear transition was occurred at different wear distance and wear rate of DCI specimens were changed by alloying elements. In severe wear condition, wear rate of DCI was dramatically increased by the addition of Mn. Although the addition of Cu 0.46wt% did not decrease the wear rate of DCI in the severe wear region, but it delayed the mild-severe wear transition. Under high pressure wear condition, wear rate and mild-severe wear transition were not concerned with hardness of DCI specimens, but they were deeply associated with impact energy changed by alloying elements.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.9 s.112
• /
• pp.900-912
• /
• 2006

A GPS receiving antenna installed in the missile's warhead is designed and fabricated at a center frequency 1.575 GHz. The circular shaped antenna is installed in the middle of the warhead where the antenna's patch and the ground plane are connected with a hollow cylindrical shaped short pin. Using the dual feeding and phase difference method, an omni-directional radiation pattern which direction is normal to the missile's axis(H-plane) is obtained. The optimized diameters of the circular patch and the cylindrical ring typed shorting pin of the GPS receiving antenna which use the FR4.material(dielectric constant $\varepsilon_r=4.6$) are 59.5 mm and 14 mm, respectively. The cylindrical body with diameter 100 mm and height 500 mm is attached to the lower part of the warhead in order to complete the missile figure. The radiation patterns are measured by changing the angle and phase between the dual feeding points. When the phase difference of dual feeding is $100^{\circ}$ and the angle between the dual feeding points is $100^{\circ}$, the nearly omni-directional radiation pattern in the H-plane is obtained. In this case, the antenna gain is -5.55 dBd and the relative level difference between the maximum and the minimum radiation intensity is 3.98 dB.

• Journal of Technologic Dentistry
• /
• v.37 no.3
• /
• pp.131-144
• /
• 2015

Purpose: This study set out to propose plans for more efficient and effective clinical practice by investigating the current state of clinical practice in the field of dental technology and thus provide basic data to develop pre- and post-education programs for clinical practice. Methods: The subjects include dental technicians at dental technical laboratories that were appointed as the place of clinical practice by the Department of Dental Technology of G University. The survey period spanned from December 22, 2014 to January 20, 2015. Total 250 questionnaires were distributed to them, and 190(76.0%) were returned. After excluding 23 whose answers were uncertain or seemed to lack reliability, total 167(66.8%) were used in final analysis. Results: 1. The most frequent practice the student did during clinical practice was articulator attachment, which was followed by pin operation or model making, one's own task and practice, sand and crow sculpturing, burying, casting, and grinding. 2. In case of going through the entire process, porcelain had the most students at 39(23.4%), being followed by crown & bridge at 28(16.8%), clinical model at 23(13.8%), full denture at 17(10.2%), and partial denture at 17(10.2%) in the order. 3. Of the students, 59.8%(30.5% for reinforced basic practice; 29.3% for intensive practice education) said that intensive practice education should be reinforced in school; and 22.3% said that intensive theory and practice education was needed, which indicates that 82.6% voiced their opinion of reinforcing education around practice. 4. The students felt that they lacked diligence, passion, and theoretical knowledge somewhat and were relatively good at clinical adaptation and operational skills. Conclusion: The findings show that the students felt an absolute lack of practice education as the school education was focused on theory and national exams in the field of dental technology, thus raising a need to reinforce practice education. Of all the respondents, 62.9% said there was a need to improve the current education with a focus on jobs. In future, education of dental technology should work to bring up able dental technicians that can perform in clinical dental technology right after graduation by reinforcing job-based practice education.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.354-357
• /
• 2009

The effect of texture of an extruded OFHC Cu rod on its sliding wear has been explored. Disk specimens with three different orientations were machined from the Cu rod for the wear test; surfaces of the disk were perpendicular ($0^{\circ}$), inclined with a specific angle ($45^{\circ}$), and parallel ($90^{\circ}$) to the extrusion axis of the rod. The texture was analyzed using an X-ray goniometer by measuring {111}, {200}, and {220} pole figures of each specimen. The analyzed texture was correlated with wear-test results of the Cu specimen. Dry sliding wear tests were performed at room temperature using a pin-on-disk wear tester against an Al2O3 ball. Applied load, sliding distance, sliding speed were fixed as 20 N, 200 m, and 0.5 m/sec, respectively. The $45^{\circ}$-inclined (to the extrusion axis) disk specimen showed the lowest wear resistance with the least data scatters. It has been found that distribution of cube texture strongly influences wear rate of the extruded Cu rod.

• Tribology and Lubricants
• /
• v.17 no.5
• /
• pp.380-385
• /
• 2001

In nuclear power steam generators, high flow rates can induce vibration of the tubes resulting in fretting wear damage due to contacts between the tubes and their supports. In this paper the fretting wear tests and the sliding wear tests were performed using the steam generator tube materials of Inconel 600 and 690 against STS 304. Sliding tests with the pin-on-disk type tribometer were done under various applied loads and sliding speeds at air environment. Fretting tests were done under various vibrating amplitudes and applied normal loads. From the results of sliding and fretting wear tests, the wear of Inconel 600 and 690 can be predictable using the work rate model. Depending on normal loads and vibrating amplitudes, distinctively different wear mechanisms and often drastically different wear rates can occur. It was found the results that the wear coefficients for Inconel 600 and 690 were 262.3$\times$10$\^$-15/Pa$\^$-1/ and 209.2$\times$10$\^$-15/Pa$\^$-1/, respectively. This study shows that Inconel 690 can provide much better wear resistance than Inconel 600 in air.

• Asian-Australasian Journal of Animal Sciences
• /
• v.14 no.3
• /
• pp.358-364
• /
• 2001

The physiochemical properties and interactions between porcine blood and waxy rice were determined. Addition of calcium chloride (0.15%) improved acceptability of blood cake and increased the gelatinization degree of waxy rice. The water-holding capacity of porcine blood gel (blood/water=60/40, v/v), extent of absorption and gelatinization of waxy rice, and scanning electron microscopy showed that blood protein matrix and waxy rice are competitors for holding water in the cooking procedure. Non-haem iron content increased linearly (R=0.95) when heating temperature rose. The presence of blood proteins caused increasing of peak temperature (Tp) of gelatinization in differential scanning calorimetric thermal gram, The microstnlcture of plasma proteins and haemoglobin appeared continuous changes, and interacted with surface of waxy rice flour in terms of network and mosaic form, respectively. The electrophoretic patterns revealed an interaction between plasma proteins and waxy rice glutelin and haemoglobin when heated could be found at temperatures above $60^{\circ}C$.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.5
• /
• pp.494-501
• /
• 2000

Effectiveness of a 3-pass plate finned-tube heat exchanger is calculated using heat exchangelet method by changing the shape of fin and the arrangement of tubes. The alternative refrigerant R134a is taken in this study. Conduction between neighboring tubes along the fin is taken into account in addition to convection between the fin and the surrounding air. Governing equations are obtained by using energy balance in a small control volume containing a tube and fins. They are numerically solved following the tube. Effect of tube-to-tube conduction is investigated in single-phase and two-phase flows with various fin shapes and arrangements of tubes. Improvement of effectiveness by fin perforation is studied too. The results shows that perforating fins, increasing the number of tubes, and increasing the distance between neighboring tubes at the same fin area enhance the effectiveness.