• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.7 no.1
• /
• pp.77-84
• /
• 2007

In this paper, Takagi-Sugeno (TS) fuzzy integral control is investigated to regulate the output voltage of an asymmetric half-bridge (AHB) DC/DC converter; First, we model the dynamic characteristics of the AHB DC/DC converter with state-space averaging method and small perturbation at an operating point. After introducing an additional integral state of the output regulation error, we obtain the $5^{th}$-order TS fuzzy model of the AHB DC/DC converter. Second, the concept of the parallel distributed compensation is applied to design the fuzzy integral controller, in which the state feedback gains are obtained by solving the linear matrix inequalities (LMIs). Finally, simulation results are presented to show the performance of the considered design method as the output voltage regulator and compared to the results for which the conventional loop gain method is used.

• Journal of Power Electronics
• /
• v.7 no.3
• /
• pp.238-245
• /
• 2007

This paper considers the problem of regulating the output voltage of a current doubler rectified asymmetric half-bridge (CDRAHB) DC/DC converter via fuzzy integral control. First, we model the dynamic characteristics of the CDRAHB converter with the state-space averaging method, and after introducing an additional integral state of the output regulation error, we obtain the Takagi-Sugeno (TS) fuzzy model for the augmented system. Second, the concept of parallel distributed compensation is applied to the design of the TS fuzzy integral controller, in which the state feedback gains are obtained by solving the linear matrix inequalities (LMIs). Finally, numerical simulations of the considered design method are compared to those of the conventional method, in which a compensated error amplifier is designed for the stability of the feedback control loop.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.2
• /
• pp.177-185
• /
• 2005

A new high efficiency DC/DC converter is proposed, which is derived from the conventional asymmetric half-bridge converter. Because the proposed converter has better ZVS condition compared with the conventional asymmetric half-bridge converter, it shows a high efficiency along the wide load range. In this paper, the basic operations of the proposed converter is analyzed and compared with that of the conventional half-bridge converter, and the excellent performance of the proposed converter is verified by the experimental results with the 425W, 385-170Vdc prototype of the power supply for PDP (Plasma Display Panel) Sustain Driver of PDP TV.

• Journal of Power Electronics
• /
• v.7 no.1
• /
• pp.21-27
• /
• 2007

This paper investigates a PID fuzzy controller for output voltage regulation of a current-doubler-rectified asymmetric half-bridge (CDRAHB) DC/DC converter. The controller is a PD-type fuzzy controller in parallel with a linear integral controller. The PD type fuzzy controller is for providing the varying gain at the different operating conditions to regulate the output voltage. The linear integral controller is for removing the steady-state error of the output voltage. In order to show the outstanding dynamic characteristics of the proposed controller, PSIM simulation studies are carried out and compared to the results for which the conventional loop gain design method is used.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.444-446
• /
• 2011

A bidirectional dual active converter with the power factor control capability is proposed as a battery charger. The source side half-bridge acts as a PWM converter that maintains the unity power factor. The battery side half-bridge converter acts as a dual active bridge (DAB) together shares the same DC link voltage with PWM converter. The imbalance voltage phenomenon is eliminated by employing asymmetric duty cycle technique. Simulation results are included to verify theoretical analysis.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.22 no.5
• /
• pp.431-439
• /
• 2017

An asymmetric half-bridge is one of the most promising topology in low-power application because of its small number of components and inherent zero-voltage switching capability. However, when it is designed taking into a hold-up time, it has large transformer offset current and small transformer turns-ratio, which severely decreases the total efficiency of s converter. In this paper, a new boost-integrated asymmetric half-bridge converter is proposed to solve these problems. The integrated boost converter compensates the hold-up time, thus facilitating optimal design in nominal state. As a result, the proposed converter can achieve high efficiency in nominal state. To verify the effectiveness of the proposed converter, an experiment is conducted using a 250-400 V input and 45 V/3.3 A output prototype.

• Proceedings of the KIEE Conference
• /
• 2004.10a
• /
• pp.169-172
• /
• 2004

This paper presents the Asymmetric Half-Bridge converter using current-doubler rectifier. Resonant conditions of the asymmetrical soft switching Half-Bridge converter is analyzed. Current-doubler converter has small voltage and current ripple. The comparison of topology compared to the secondary rectification for center-tap type and current-doubler type are discussed. Experimental result are obtained on a 5V, 20A DC/DC Half-Bridge converter MOSFET based prototype for the 100W.

• Journal of Power Electronics
• /
• v.17 no.6
• /
• pp.1391-1401
• /
• 2017

In this paper, a secondary resonance half-bridge dc-dc converter with an inductive output filter is presented. The primary side of such a converter utilizes asymmetric pulse width modulation (APWM) to achieve zero-voltage switching (ZVS) of the switches, and clamps the voltage of the switch to the input voltage. In addition, zero current switching (ZCS) of the output diode is achieved by a half-wave rectifier circuit with a filter inductor and a resonant branch in the secondary side of the proposed converter. Thus, the switching losses and diode reverse-recovery losses are eliminated, and the performance of the converter can be improved. Furthermore, an inductive output filter exists in the converter reduce the output current ripple. The operational principle, performance analysis and design equation of this converter are given in this paper. The analysis results show that the output diode voltage stress is independent of the duty cycle, and that the voltage gain is almost linear, similar to that of the isolation Buck-type converter. Finally, a 200V~380V input, 24V/2A output experimental prototype is built to verify the theoretical analysis.

• Journal of Power Electronics
• /
• v.7 no.4
• /
• pp.328-335
• /
• 2007

A conventional Single-Stage Power-Factor-Correction (PFC) AC/DC converter has a link capacitor voltage problem under high line input and low load conditions. In this paper, this problem is analyzed by using the voltage conversion ratio of the DC/DC conversion cell. By applying this analysis, a new Single-Stage PFC AC/DC converter with a boost PFC cell integrated with a Voltage-Doubler Rectified Asymmetrical Half-Bridge (VDRAHB) is proposed. The proposed converter features good power factor correction, low current harmonic distortions, tight output regulations and low voltage of the link capacitor. An 85W prototype was implemented to show that it meets harmonic requirements and standards satisfactorily with near unity power factor and high efficiency over universal input.

• Journal of Power Electronics
• /
• v.12 no.2
• /
• pp.258-267
• /
• 2012

An interleaved single-stage AC/DC converter with a boost converter and an asymmetrical half-bridge topology is presented to achieve power factor correction, zero voltage switching (ZVS) and load voltage regulation. Asymmetric pulse-width modulation (PWM) is adopted to achieve ZVS turn-on for all of the switches and to increase circuit efficiency. Two ZVS half-bridge converters with interleaved PWM are connected in parallel to reduce the ripple current at input and output sides, to control the output voltage at a desired value and to achieve load current sharing. A center-tapped rectifier is adopted at the secondary side of the transformers to achieve full-wave rectification. The boost converter is operated in discontinuous conduction mode (DCM) to automatically draw a sinusoidal line current from an AC source with a high power factor and a low current distortion. Finally, a 240W converter with the proposed topology has been implemented to verify the performance and feasibility of the proposed converter.