• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.12
• /
• pp.3909-3916
• /
• 1996

Magnetic bearing is the machine element that supports the shaft without mechanical contact using the magnetic force induced by permanent magnet of electromagnet. Active magnetic bearing system is composed of sensor, controller, power amplifier, and electromagnet. If all the elements were dieal, shaft position could be controlled to sensor resolution, Because each elements inreal system have mechanical and electricla losses and nonlinearity, it is impossible to attain the desired performance using general control algorithm. So far it has been studied on improvement of the control algorithm of the electric characteristics of each elements. Another factors to affect shaft behavior are the manufacturing errors due to machine work, and assembling errors due to accumulate manufacturing errors of the radial magnetic bearing. This paper describes that the shaft behavior due to accumulate manufacturing errors and asymmetric bolting. This paper describes that the shaft behavior due to assembling errors of the radial bearings donot affect the rotaitonal accuracy of the shaft. But when the amplitude of the assembling errors increasees over the certain value, the bearing can not support the shaft properly.

• Journal of the Korean Professional Engineers Association
• /
• v.22 no.3
• /
• pp.5-13
• /
• 1989

A major problem of stopwatch time study is how to do for the accurate and consistent performance rating, which is one of the critical variables to determine the accuracy of work measurement and should be still dependent upon time observer's judgement. Therefore the time observer's ability for the performance rating is very important, and must be improved by correct training method and procedure. This paper developed a new benchmark and benchmark-observation method for the effective performance rating training of assembling and machining operations. The trainees' ability in the accuracy and consistency of the performance rating ,improved significantly after being trained by subject method. The percentage improvement in rating accuracy and consistency values was 34.7% and 49% respectively. In addition, benchmark-practice method for the performance rating training is not significant, so it is proofed that the skill of a certain operation is not important for the improvement of the rating ability.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.381-386
• /
• 2002

In this paper, we have proposed a new approach to the design of robot vision system to develop the technology for the automatic test and assembling of precision mechanical and electronic parts for the factory automation. In order to perform real time implementation of the automatic assembling tasks in the complex processes, we have developed an intelligent control algorithm based-on neural networks control theory to enhance the precise motion control. Implementing of the automatic test tasks has been performed by the real-time vision algorithm based-on TMS320C31 DSPs. It distinguishes correctly the difference between the acceptable and unacceptable defective item through pattern recognition of parts by the developed vision algorithm. Finally, the performance of proposed robot vision system has been illustrated by experiment for the similar model of fifth cell among the twelve cell for automatic test and assembling in S company.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.04a
• /
• pp.217-222
• /
• 2001

In this paper, we have proposed a new approach to the design of robot vision system to develop the technology for the automatic test and assembling of precision mechanical and electronic parts for the factory automation. In order to perform real time implementation of the automatic assembling tasks in the complex processes, we have developed an intelligent control algorithm based-on neural networks control theory to enhance the precise motion control. Implementing of the automatic test tasks has been performed by the real-time vision algorithm based-on TMS320C31 DSPs. It distinguishes correctly the difference between the acceptable and unacceptable defective item through pattern recognition of parts by the developed vision algorithm. Finally, the performance of proposed robot vision system has been illustrated by experiment for the similar model of fifth cell among the twelve cell for automatic test and assembling in S company.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.279-279
• /
• 2000

In this paper, we have proposed a new approach to the design of robot vision system to develop the technology for the automatic test and assembling of precision mechanical and electronic parts fur the factory automation. In order to perform real time implementation of the automatic assembling tasks in the complex processes, we have developed an intelligent control algorithm based-on neural networks control theory to enhance the precise motion control. Implementing of the automatic test tasks has been performed by the real-time vision algorithm based-on TMS320C31 DSPs. It distinguishes correctly the difference between the acceptable and unacceptable defective item through pattern recognition of parts by the developed vision algorithm. Finally, the performance of proposed robot vision system has been illustrated by experiment for the similar model of fifth cell among the twelve cell fur automatic test and assembling in S company.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.96-101
• /
• 2000

In this paper, we have proposed a new approach to the design of robot vision system to develop the technology for the automatic test and assembling of precision mechanical and electronic parts for the factory automation. In order to perform real time implementation of the automatic assembling tasks in the complex processes, we have developed an intelligent control algorithm based-on neural networks control theory to enhance the precise motion control. Implementing of the automatic test tasks has been performed by the real-time vision algorithm based-on TMS320C31 DSPs. It distinguishes correctly the difference between the acceptable and unacceptable defective item through pattern recognition of parts by the developed vision algorithm. Finally, the performance of proposed robot vision system has been illustrated by experiment for the similar model of fifth cell among the twelve cell for automatic test and assembling in S company.

• 정보저장시스템학회:학술대회논문집
• /
• 2005.10a
• /
• pp.2-3
• /
• 2005

Air gap control method using a conventional actuator for near field recording technology has been reported. To achieve good performance in the air gap servo and further experiments, the assembling between OL and SIL is the critical procedure. A lens set with NA 1.45 at 405 m has been assembled and tested by using a Twyman-Green interferometer. The tolerance of assembling is very tight and the designing and adjusting procedure must be carefully controlled.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.2B
• /
• pp.203-209
• /
• 2004

In OBS networks, the burst dropping due to contention significantly affects the performance of TCP, but existing drop policies have not considered this problem and researches related to TCP have been mainly studied on burst assembling. We propose the drop policy considering retransmission of TCP to improve the performance of TCP in OBS networks. The proposed drop policy is the Retransmission Count-based DP that regards retransmission count of bursts as priority when it selects dropping burst. This paper evaluates the performance of RC-based DP model and general DP model using ns-2. The metrics of performance evaluation are TCP throughput, maximum sequence number of received TCP packets and drop rate of packet as simulation time increases.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.6
• /
• pp.98-103
• /
• 2015

Swing reducers are widely used in special vehicles that have swing motions. Generally, compact swing reducers were constituted by a worm gear pair. Worm gears are one of the most important technical devices for transmitting torque between spatially crossed axes. Due to their high transmission ratio and compact structure, they are widely used in power transmission applications where high reduction is required. This paper presented approaches to improve the transmission efficiency and assembling performance of 3.5 ton class worm gear swing reducers. Worm wheel and the case of swing reducers were optimized and certified by a finite element method. Finally, an actual swing reducer was processed and assembled to test the performance.

• Proceeding of Spring/Autumn Annual Conference of KHA
• /
• 2008.11a
• /
• pp.448-451
• /
• 2008

This study is under doing to suggest application manual using assembling reference plane design & standard finish material basis upon material classification code as a tool of a linkage between building design and construction standarization in order to enlarge the applicability of house building material that is produced by the module plant. We can say the goal of building standardization intend not only the improvement of construction productibility but also guarantee of subsequent performance through automatization basis upon informationalization of building design. For a etabilishing of this condition, it is neccessary to link the standardization's result of material--design--construction field. According to this neccessity, we are going to suggest information factor that can make relative business manager easily approach to the standardization practical task.