• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 춘계학술발표대회 논문집
• /
• pp.113-116
• /
• 2003

The investigation of delamination growth behavior in hybrid composite material such as FRMLs should be considered delamination growth rate, dA_D/da$ using the delamination shape factor, $f_S$ instead of traditional fracture mechanics parameters. The main objective of this study is to evaluate the relationship between delamination element (i. e. delamination width, b, delamination contour, c, delamination shape factor, $f_S$ and delamination growth rate, dA_D/da$) and delamination growth in FRMLs under cyclic bending moment. The delamination shape formed along the fatigue crack between aluminum layer and glass fiber/epoxy layer are measured by scanning method. The details of study are as follow : ⅰ) Relationship between crack length, a and delamination width, b. ⅱ) Variation of delamination growth rate, dA_D/da$ was attendant on delamination shape factors, $f_{S1}$, $f_{S2}$, $f_{S3}$. The test result indicated the delamination growth behavior depends in delamination element such as delamination width, b, delamination shape factors, $f_{S1}$, $f_{S2}$, $f_{S3}$.

• 한국진공학회지
• /
• 제15권1호
• /
• pp.97-102
• /
• 2006

양극 산화된 알루미나 (anodized aluminum oxide : AAO)는 균일하고 일정한 크기의 나노기공 패턴을 지니고 있다. AAO를 이온빔 나노 patterning을 위한 이온조사 시 마스크로서 이용하기 위해 AAO 나노 기공을 통과하는 이온빔의 투과율(AAO에 입사한 이온에 대한 투과이온의 양의 비)을 측정하였다. Al bulk foil을 양극 산화하여 두께가 $4{\mu}m$이고 종횡비(두께와 기공의 지름의 비)가 각각 200:1, 100:1 인 AAO를 Goniometer에 부착하여 500 keV의 $O^{2+}$ 이온빔에 대해 나노기공을 정렬시킨 후, 기울임 각에 따른 투과율을 측정한 결과, 종횡비가 200:1, 100:1 일 때 투과율은 각각 약 $10^{-8},\;10^{-4}$로 거의 이온빔이 투과하지 못하였다. 반면에 $SiO_2$ 위에 증착된 Al 박막으로 양극산화하여 종횡비가 5:1인 AAO의 이온빔 투과율은 0.67로 투과율이 현저히 향상되었다. 높은 종횡비를 갖는 AAO의 경우에는 범과 AAO 기공의 정렬이 쉽지 않은데다 알루미나의 비전도성으로 인한 charge-up 현상으로 인해 이온빔이 극히 투과하기 어렵기 때문이다. 실제로 80 keV의 Co 음이온을 종횡비 5:1인 AAO에 조사시킨 후에는 AAO 나노기공과 동일한 크기의 나노 구조체가 형성됨을 주사전자현미경(scanning electron microscopy: SEM) 관찰을 통하여 확인하였다.

• 한국재료학회지
• /
• 제14권9호
• /
• pp.619-626
• /
• 2004

Pulsed metalorganic chemical vapor deposition (MOCVD) of conformal copper seed layers, for the electrodeposition Cu films, has been achieved by an alternating supply of a Cu(I) source and $H_2$ reactant at the deposition temperatures from 50 to $100^{\circ}C$. The Cu thickness increased proportionally to the number of cycles, and the growth rate was in the range from 3.5 to $8.2{\AA}/cycle$, showing the ability to control the nano-scale thickness. As-deposited films show highly smooth surfaces even for films thicker than 100 nm. In addition about a $90\%$ step coverage was obtained inside trenches, with an aspect ratio greater than 30:1. $H_2$, introduced as a reactant gas, can play an active role in achieving highly conformal coating, with increased grain sizes.

• 대한기계학회논문집A
• /
• 제28권5호
• /
• pp.524-531
• /
• 2004

To investigate relevance of the definition of the reference stress to estimate J and $C^{*}$ for surface crack problems, this paper compares FE J and $C^{*}$ results for surface cracked pipes with those estimated according to the reference stress approach using various definitions of the reference stress. Pipes with part circumferential inner surface crack and finite internal axial crack are considered, subject to internal pressure and global bending. The crack depth and aspect ratio are systematically varied. The reference stress is defined in four different ways using (i) the local limit load, (ii) the global limit load, (iii) the global limit load determined from the FE limit analysis, and (iv) the optimized reference load. It is found that the reference stress based on the local limit load gives overall excessively conservative estimates of J and $^{*}$. Use of the global limit load clearly reduces the conservatism, compared to that of the local limit load, although it can provide sometimes non-conservative estimates of J and $^{*}$. The use of the FE global limit load gives overall non-conservative estimates of J and $^{*}$. The reference stress based on the optimised reference load gives overall accurate estimates of J and $^{*}$, compared to other definitions of the reference stress. Based on the present finding, general guidance on the choice of the reference stress for surface crack problems is given.

• 한국세라믹학회지
• /
• 제40권9호
• /
• pp.867-873
• /
• 2003

$Si_{3}N_{4}$-BN계 기계 가공서 세라믹스를 $1800^{\circ}C$에서 2시간동안 25MPa의 압력하에서 열간 가압소결하여 제조하였다. $Si_{3}N_{4}$ 매트릭스에 판상의 h-BN 첨가량을 5-30 vol%까지 증가함에 따라 굽힘강도는 $Si_{3}N_{4}$ 단미의 1000 MPa에서 720~400 MPa로 감소하였고, 파괴인성도 $Si_{3}N_{4}$ 단미의 7.6MPaㆍ$m^{1/2}$에서 6.5~4.1 MPaㆍ$m^{1/2}$로 감소하였다. $\beta$-$Si_{3}N_{4}$의 결정립 크기와 형상비는 h-BN 첨가에 의해 약간 감소하였다. $Si_{3}N_{4}$ 단미는 절삭시 취성 파괴를 나타내어 절삭이 불가능하였으나, $Si_{3}N_{4}$-BN계 기계 가공서 세라믹스는 파괴가 발생하지 않으면서 절삭이 가능하여, 우수한 기계 가공성을 나타내었다. h-BN 함량이 증가할수록 절삭과 마이크로 드릴링시의 절삭력은 감소하였다.

• Fisheries and Aquatic Sciences
• /
• 제1권2호
• /
• pp.242-249
• /
• 1998

The engineering aspect of water treatment processes in the recirculating aquaculture system was studied. To recycle the water in the aquaculture system, a wastewater treatment process was required to maintain high water quality for the growth and health of the cultured fish. In this study, three different biofilm processes were used to reduce the concentration of organic matters and ammonia from the recirculating water - two phase fluidized bed, three phase fluidized bed, and trickling filter. The objectives of this research were to evaluate the optimum treatment conditions of the biofilm processes for the recirculating aquaculture system, and thereby reduce the volume of biofilm processes, which are commonly used for the recycle water treatment processes for aquaculture. The result of this study showed that the removal efficiency of organic matters by trickling filter was found to be lower than that of the fluidized bed. In the trickling filter system, anthracite showed better organic removal efficiency than crushed stone as a media. In the two phase fluidized bed, the maximum removal efficiency of either organics or ammonia was obtained when both the packing rate of media was maintained to $40\%$ of total reactor depth excepting sediment zone and the bed expansion rate was maintained to $100\%$. When 100 tilapia (Oreochromis niloticus) of each average 200g was reared, the pollutant production rate was 0.07g $NH_4\;^+-N/kg$ fish/day and 0.06g P04-3-P/kg fish/day, and sludge production rate was 0.39 g SS/kg fish/day. In the two phase and three phase fluidized bed, the volume of water treatment tank could be calculated from an empirical equation by using the relationship between the influent COD to $NH_4\;^+-N$ ratio (C/N, -), media concentration (Cm, g/L), influent ammonia nitrogen concentration (Ni, mg/L), effluent ammonia nitrogen concentration (Ne, mg/L), bed expansion rate $(E,\;\%)$, and influent flowrate $(Q,\;m^3/hr)$. The empirical equation from this study is $$V_2\;=\;10^{3.1279}\;C/N^{3.5461}\;C_m\;^{-3.7473}\;N_i\;^{4.6477}\;E^{0.0326}\;N_e\;^{-0..8849}\;Q\;(Two\;Phase\;FB) V_3\;=\;10^{11.7507}\;C/N^{-1.2330}\;C_m\;^{-6.5715}\;N_i\;^{1.5091}\;N_e\;^{-1.8489}\;Q (Three\;Phase\;FB)$$

• 한국재료학회지
• /
• 제22권4호
• /
• pp.202-206
• /
• 2012

$CoSi_2$ was formed through annealing of atomic layer deposition Co thin films. Co ALD was carried out using bis(N,N'-diisopropylacetamidinato) cobalt ($Co(iPr-AMD)_2$) as a precursor and $NH_3$ as a reactant; this reaction produced a highly conformal Co film with low resistivity ($50\;{\mu}{\Omega}cm$). To prevent oxygen contamination, $ex-situ$ sputtered Ti and $in-situ$ ALD Ru were used as capping layers, and the silicide formation prepared by rapid thermal annealing (RTA) was used for comparison. Ru ALD was carried out with (Dimethylcyclopendienyl)(Ethylcyclopentadienyl) Ruthenium ((DMPD)(EtCp)Ru) and $O_2$ as a precursor and reactant, respectively; the resulting material has good conformality of as much as 90% in structure of high aspect ratio. X-ray diffraction showed that $CoSi_2$ was in a poly-crystalline state and formed at over $800^{\circ}C$ of annealing temperature for both cases. To investigate the as-deposited and annealed sample with each capping layer, high resolution scanning transmission electron microscopy (STEM) was employed with electron energy loss spectroscopy (EELS). After annealing, in the case of the Ti capping layer, $CoSi_2$ about 40 nm thick was formed while the $SiO_x$ interlayer, which is the native oxide, became thinner due to oxygen scavenging property of Ti. Although Si diffusion toward the outside occurred in the Ru capping layer case, and the Ru layer was not as good as the sputtered Ti layer, in terms of the lack of scavenging oxygen, the Ru layer prepared by the ALD process, with high conformality, acted as a capping layer, resulting in the prevention of oxidation and the formation of $CoSi_2$.

• 한국진공학회지
• /
• 제22권3호
• /
• pp.156-161
• /
• 2013

연속적인 1차원의 나노섬유를 제작하는데 빠르고 효과적인 방법인 전기방사법을 이용하여 Ag 나노섬유로 이루어진 투명전극을 제작하고 그 특성을 측정하였다. 전기방사를 통해 제조된 Ag 나노섬유는 큰 종횡비를 갖게 되며 열처리를 통해 생성된 섬유사이의 fused junction이 접촉저항을 낮추어 전기적 특성을 향상시킨다. Ag/고분자 용액을 졸-겔 방법을 이용하여 제조한 후 glass 기판위에 방사시켜 Ag/고분자 나노섬유 구조체를 제작하고 $200{\sim}500^{\circ}C$, 2시간 열처리하여 고분자가 일정부분 제거되고 전도성이 향상된 Ag 나노섬유 투명전극을 제조하였다. Ag 나노섬유의 모폴로지를 FE-SEM을 통해 확인하였고 Ag 나노섬유 투명전극의 투과도와 면저항을 UV-vis-NIR spectroscopy와 I-V특성 측정장치를 사용하여 측정하였다. 투과도 83%에서 면저항 $250{\Omega}/sq$의 투명전극을 제작하였으며 전도성필름에 적합한 수준이다. Ag 나노섬유로 이루어진 투명 전극은 전기적, 광학적, 기계적 특성이 우수하여 차세대 유연 디스플레이에 적용 가능성을 보여준다.

• International Journal of Oral Biology
• /
• 제39권2호
• /
• pp.107-114
• /
• 2014

Taste is an important sense in survival and growth of animals. The growth and maintenance of taste buds, the receptor organs of taste sense, are under the regulation of various neurotrophic factors. But the distribution aspect of neurotrophic factors and their receptors in distinct taste cell types are not clearly known. The present research was designed to characterize mRNA expression pattern of neurotrophic factors and their receptors in distinct type of taste cells. In male 45-60 day-old Sprague-Dawley rats, epithelial tissues with and without circumvallate and folliate papillaes were dissected and homogenized, and mRNA expressions for neurotrophic factors and their receptors were determined by RT-PCR. The mRNA expressions of brain-derived neurotrophic factor (BDNF), neurotrophin-3 (NT3), receptor tyrosine kinase B (TrkB), exclusion of nerve growth factor (NGF), neurotrophin-4/5 (NT4/5), receptor tyrosine kinase A (TrkA), receptor tyrosine kinase C (TrkC), and p75NGFR were observed in some population of taste cell. In support of this result and to characterize which types of taste cells express NT3, BDNF, or TrkB, we examined mRNA expressions of NT3, BDNF, or TrkB in the $PLC{\beta}2$ (a marker of Type II cell)-and/or SNAP25 (a marker of Type III cell)-positive taste cells by a single taste cell RT-PCR and found that the ratio of positively stained cell numbers were 17.4, 6.5, 84.1, 70.3, and 1.4 % for $PLC{\beta}2$, SNAP25, NT3, BDNF, and TrkB, respectively. In addition, all of $PLC{\beta}2$-and SNAP25-positive taste cells expressed NT3 mRNA, except for one taste bud cell. The ratios of NT3 mRNA expressions were 100% and 91.7% in the SNAP25-and $PLC{\beta}2$-positive taste cells, respectively. However, two TrkB-positive taste cells co-expressed neither $PLC{\beta}2$ nor SNAP 25. The results suggest that the most of type II or type III cells express BDNF and NT3 mRNA, but the expression is shown to be less in type I taste cells.

• 대기
• /
• 제29권3호
• /
• pp.311-324
• /
• 2019

We employed a Multi-Angle Snowflake Camera (MASC) to quantitatively analyze snow particles at the ground level in the Yeongdong region of Korea. The MASC captures high-resolution photographs of hydrometeors from three angles and simultaneously measures fallspeed. Based on snowflake images of the several episodes in 2017 and 2018, we derived statistics of size, aspect ratio, orientation, complexity, and fallspeed of snow crystals, which generally showed similar characteristics to the previous studies in other regions of the world. Dominant snow crystal habits of January 22, 2018 generated by northerly were melted aggregates when 850 hPa temperature was about $-6{\sim}-8^{\circ}C$. Average fallspeed of snow crystals was $1.0m\;s^{-1}$ though its size gradually increased as temperature decreased. Another snowfall event (March 8, 2018) was driven by the baroclinic instability as accompanied with a deep trough. Snow crystal habits were largely rimed aggregates (complexity ~1.8) and melting particles of dark images. Meanwhile, in the extreme snowfall event whose snow rate was greater than $10cm\;hr^{-1}$ on January 20, 2017, main snow crystals appeared to be heavily rimed particles with relatively smaller size when convective clouds developed vertically up to 9 km in association with tropopause folding. MASC also could successfully measure a decrease in snow crystal size and an increase in riming degree after AgI seeding at Daegwallyeong on March 14, 2017.