• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.399-401
• /
• 2000

Recently polymer insulators are being used for outdoor high voltage applications. Polymer insulators for transmission and distribution line have significant advantages over porcelain and glass insulators, especially for ultra-high voltage(UHV) transmission lines. Their advantages are light weight, vandalism resistance and hydrophobicity. In this paper, polymer line post insulator has been designed and investigated electric field distribution by FEM. Designed LP insulators have been tested as insulator performance test, such as power frequency voltage test, lightning impulse voltage test, artificial pollution test and flexural load test.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.5
• /
• pp.732-738
• /
• 2015

In ac discharge, emission efficiency shows an time-varying characteristics during discharge. The phenomenon is caused by the potential distribution changes during the discharge, which indicates that a specific potential distribution can contribute to a high improvement of the emission efficiency. To create an artificial environment for a potential distribution favorable to emission efficiency, we used the asymmetric electrode structure and proved the capability. Our results showed that the ratio of the area of anode to cathode became larger, the emission efficacy was greatly improved.

• Journal of Korean Society of Water and Wastewater
• /
• v.11 no.3
• /
• pp.51-58
• /
• 1997

Determining sizes and the locations of reservoirs in the water distribution system(WDS) with multi-reservoirs is much difficult than that with single reservoir. The extended period simulation(EPS) models provide more comprehensive analysis of water distribution systems than the steady-state models can do. Therefore, EPS models should be applied to the WDS with multi-reservoirs. This study is to investigate the variations of required reservoir sizes and residual nodal pressures according to reservoir locations. In this study, EPS was applied to analyze an artificial and a real WDS under several water demand patterns. As a result, it was found that water demand patterns make no significant differences in the determining of the reservoir size, if they have similar peaking factors. And the variations of the peaking factor should be carefully checked in the design and the analysis of the WDS with multi-reservoirs, because the peaking factor itself will affect the minimum allowable sizes of reservoirs in those systems.

• Computers and Concrete
• /
• v.12 no.5
• /
• pp.613-625
• /
• 2013

In this study, Artificial Neural Networks (ANN) analysis is used to predict the compression strength of polypropylene fibre mixed concrete. Polypropylene fibre admixture increases the compression strength of concrete to a certain extent according to mix proportion. This proportion and homogenous distribution are important parameters on compression strength. Determination of compression strength of fibre mixed concrete is significant due to the veridicality of capacity calculations. Plenty of experiments shall be completed to state the compression strength of concrete which have different fibre admixture. In each case, it is known that performing the laboratory experiments is costly and time-consuming. Therefore, ANN analysis is used to predict the 7 and 28 days of compression strength values. For this purpose, 156 test specimens are produced that have 26 different types of fibre admixture. While the results of 120 specimens are used for training process, 36 of them are separated for test process in ANN analysis to determine the validity of experimental results. Finally, it is seen that ANN analysis predicts the compression strength of concrete successfully.

• Progress in Superconductivity
• /
• v.11 no.1
• /
• pp.52-56
• /
• 2009

Temperature distributions and thermal stresses were calculated and analyzed to investigate the effect of the artificial holes to the transient behaviors of the superconductors which was cooled in liquid nitrogen. Three dimensional finite element method was used to calculated the transient temperature and thermal stresses in the superconductors. The cooling speed of the superconductors with holes is faster than those without holes. Because the thermal stresses calculated in the superconductors can be relaxed by the distributed holes, the volume of the peak tensile stress decreases during the cooling in liquid nitrogen. If optimal metal, which can maintain the relaxation of thermal stresses, is used to fill and reinforce the artificial holes, the probability of failure of the superconductors may be decreased by the decrease of volume of peak tensile stress.

• Journal of Environmental Health Sciences
• /
• v.35 no.5
• /
• pp.417-425
• /
• 2009

The purpose of this study was to investigate the whitening effect of Angelicae dahuricae Radix water extract (ADWE) by its application on artificial tanning spots which were induced by 1,500 $mJ/cm^2$ of UVB radiation on the backs of brown guinea pigs weighing approximately 450~500 g. Thirty ${\mu}l$ of ADWE, at each application, were applied twice a day, 5 days a week, for 8 weeks to the guinea pigs. The artificial tanning spots were divided into 3 groups which were vehicle control group [propylene glycol: ethanol: water (5:3:2)], positive control group (2% hydroquinone) and experimental group (2% ADWE). The visible whitening effect and changes in melanin index were evaluated once a week. On completion of the experiment, the animals were sacrificed under anesthetization, and the artificial tanning spots were excised by biopsy punch and stained with Hematoxylin and Eosin (H&E) to observe histological change and also stained with Fontana-Masson's silver (F-M) and S-100 to observe melanin pigmentation and melanocytes. In the gross observation, the experimental group showed higher pigmentation than the positive control group but lower pigmentation than the vehicle control group. Histological observation confirmed that ADWE had a positive whitening effect by showing a lower distribution of melanin and melanocytes in the epidermis of experimental group than in the vehicle control group.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.39 no.spc1
• /
• pp.223-230
• /
• 2006

We investigated the spring and summer community structure of meiobenthos in a tidal-falt near Iwon, Korea, in 2002 and 2003. In total, 12 meiofaunal groups were found in the study area among which nematodes were the most dominant. Benthic foraminiferans, harpacticoid copepods, polychaetes, and crustacean nauplli were also dominant groups at all sites. The total density of meiobenthos at each station was be 246-2,177 ind./$10cm^2$. As the depth of sediment increased, the density of meiobenthos at each station gradually decreased. Changes in the vertical distribution of meiobenthos in the study area occurred mainly near the sediment surface (0-1 cm). Generally, between spring and summer the density of nematodes increased, and the density of other dominant meiofaunal groups (benthic harpacticoids, crustacean nauplii, benthic foraminiferans) decreased near the sediment trap the control site of sediment traps compared to that at the control site. The results of cluster and multidimensional scaling plots indicate that the meiofaunal community changed following construction of a low artificial wood groin structure.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.64-71
• /
• 2009

The stresses acting on shotcrete lining of tunnel have been measured virtually by monitoring instruments installed during construction. However, the malfunction of instrument and the lack of consistency of signal have always been controversial, but re-installation of instrument after construction of tunnel lining is practically impossible. Therefore, authors have carried out the study to develop a new technique for estimating the stress acting on shotcrete lining during and after construction. In the technique, stresses of shotcrete lining can be estimate by the measurement of deformation of free face. Therefore, the relationships between the stresses of shotcrete lining and deformation of free surface are indispensable factor. In this paper, the parametric study using 2D FEM analysis was carried out to estimate the relationships between the stress level acting on the tunnel shotcrete lining and the deformation near the free face (e.g. artificial crack in this study). The distribution of stresses of shotcrete lining is also investigated in this study as the preliminary investigation for the large-scale tunnel lining test and detailed 3D FEM analysis.

• Journal of Ocean Engineering and Technology
• /
• v.20 no.4 s.71
• /
• pp.43-49
• /
• 2006

Detailed investigations were carried out on the stability of the dredged soil bed against wave actions, aimedat establishing the design method of artificial tidal flats using dredged soil. The soil was dredged at Nagoya port, Japan, and has a mean grain size of 0.013mm. Basic features of artificial dredged soil bed against wave actions were explained from a series of model experiments in a wave flume. The two types of section shapes were employed; one is a horizontal bed and the other is a sloped one. Changes of the bed profile, shear strength, grain size distribution and water content, according to the wave actions, were measured in detail. The cumulative effect of the wave actions, over about one week, was investigated. A dredged soil bed moves withthe wave actions with relatively small wave height. It should be especially. noted that the clay component is dissolved and flown out, away from the surface layer, and consequently the surface layer hardens, as if it is covered with sand. Wren the wave height is gradually increased, the bed is not liquefied and the shear strength of the dredged bed is increased by a wave-induced dissipation of pore pressures in the bed and a decrease of clay component by the wave-induced leakage.

• Journal of Applied Reliability
• /
• v.16 no.1
• /
• pp.48-55
• /
• 2016

Purpose: The purpose of this study is to identify the object-oriented metrics which have strong impact on the reliability and fault-proneness of software products. The reliability and fault-proneness of software product is closely related to the design properties of class diagrams such as coupling between objects and depth of inheritance tree. Methods: This study has empirically validated the object-oriented metrics to determine which metrics are the best to predict fault-proneness. We have tested the metrics using logistic regressions and artificial neural networks. The results are then compared and validated by ROC curves. Results: The artificial neural network models show better results in sensitivity, specificity and correctness than logistic regression models. Among object-oriented metrics, several metrics can estimate the fault-proneness better. The metrics are CBO (coupling between objects), DIT (depth of inheritance), LCOM (lack of cohesive methods), RFC (response for class). In addition to the object-oriented metrics, LOC (lines of code) metric has also proven to be a good factor for determining fault-proneness of software products. Conclusion: In order to develop fault-free and reliable software products on time and within budget, assuring quality of initial phases of software development processes is crucial. Since object-oriented metrics can be measured in the early phases, it is important to make sure the key metrics of software design as good as possible.