• 한국터널지하공간학회 논문집
• /
• 제2권2호
• /
• pp.50-61
• /
• 2000

터널의 갱구부는 터널에서 3차원 거동을 가장 뚜렷하게 보이는 부분이며 대체로 풍화가 진행되어 거의 토사화되어 있는 취약한 암반에 시공됨에 따라 비탈면은 잠재적인 활동체가 되게 된다. 터널 갱구부 비탈면에서 안정에 위해되는 요인이 발생했을 경우 파괴가 급속히 진행되어 대형사고로 이어질수 있으므로 특별한 안정화 대책이 필요하여 경제적으로 큰 부담이 된다. 이를 해결하기 위한 방안으로 갱구부 비탈면을 수평 아치형으로 굴착하게 되면 굴착량이 줄어서 경제적이고 자연훼손이 줄어들며 보다 안전하고 아름다운 형상을 기대할 수 있다. 그러나 인식부족으로 인하여 이와 같은 시도는 거의 이루어지지 않고 있어서 면벽식 갱구부가 보편화 되어 있는 실정이다. 본 연구에서는 아치형 갱구부 비탈면의 이점을 알아보기 위하여 3차원 수치해석을 ㄷ형과 아치형 비탈면에 대하여 각각 수행하여 그 결과를 서로 비교하였으며 터널 굴진과 암반강성에 따른 갱구부 비탈면의 안정성은 비탈면에서 발생되는 최대전단변형율과 막장면에서 터널굴진에 따른 소성접근도를 분석하여 검토하였다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제17권2호
• /
• pp.260-264
• /
• 2017

Process variation effect on arch-structured gate stacked array (GSTAR) 3-D NAND flash is investigated. In case of arch-structured GSTAR, a shape of the arch channel is depending on an alignment of photo-lithography. Channel width fluctuates according to the channel hole alignment. When a shape of channel exceeds semicircle, channel width becomes longer, increasing drain current. However, electric field concentration on tunnel oxide decreases because less electric flux converges into a larger surface of tunnel oxide. Therefore, program efficiency is dependent on the process variation. Meanwhile, a radius of channel holes near the bottom side become smaller due to an etch slope. It also affects program efficiency as well as channel width. Larger hole radius has an advantage of higher drain current, but causes degradation of program speed.

• Geomechanics and Engineering
• /
• 제23권5호
• /
• pp.481-491
• /
• 2020

Piles installed in row(s) are used as an effective technique to improve the stability of soil slopes. The analysis of pile-stabilized slopes require a reliable prediction of lateral resistance offered by the piles. In this work, an analytical solution is developed to estimate the lateral resistance offered by the stabilizing piles in sand and c - 𝜙 soil slopes considering soil arching phenomenon. The soil arching in both horizontal direction (between the neighboring piles) and vertical direction (in the active wedge in front of the pile row) are studied and their effects are incorporated in the proposed model. The shape of soil arch is assumed to be circular and principal stress trajectories are defined separately for both modes of arching. Experimental and numerical studies found in literature were used to validate the proposed method. A detailed parametric analysis was performed to study the influence of pile diameter, center-to-center spacing, slope angle and angle of internal friction on the lateral pile resistance.

• Journal of Biosystems Engineering
• /
• 제28권1호
• /
• pp.65-76
• /
• 2003

The analysis of cow body parameters is important to provide some useful information fur cow management and cow evaluation. Present methods give many stresses to cows because they are invasive and constrain cow postures during measurement of body parameters. This study was conducted to develop the stereo vision system fur non-invasive analysis of cow body features. Body feature parameters of 16 heads at two farms(A, B) were measured using scales and nineteen stereo images of them with walking postures were captured under outdoor illumination. In this study, the camera calibration and inverse perspective transformation technique was established fer the stereo vision system. Two calibration results were presented for farm A and fm B, respectively because setup distances from camera to cow were 510 cm at farm A and 630cm at farm B. Calibration error values fer the stereo vision system were within 2 cm for farm A and less than 4.9 cm for farm B. Eleven feature points of cow body were extracted on stereo images interactively and five assistant points were determined by computer program. 3D world coordinates for these 15 points were calculated by computer program and also used for calculation of cow body parameters such as withers height. pelvic arch height. body length. slope body length. chest depth and chest width. Measured errors for body parameters were less than 10% for most cows. For a few cow. measured errors for slope body length and chest width were more than 10% due to searching errors fer their feature points at inside-body positions. Equation for chest girth estimated by chest depth and chest width was presented. Maximum of estimated error fur chest girth was within 10% of real values and mean value of estimated error was 8.2cm. The analysis of cow body parameters using stereo vision system were successful although body shape on the binocular stereo image was distorted due to cow movements.