• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.4
• /
• pp.11-18
• /
• 2011

The quantitative interfacial adhesion energy of the Cu-Cu direct bonding layers was evaluated in terms of the bonding temperature and Ar+$H_2$ plasma treatment on Cu surface by using a 4-point bending test. The interfacial adhesion energy and bonding quality depend on increased bonding temperature and post-annealing temperature. With increasing bonding temperature from $250^{\circ}C$ to $350^{\circ}C$, the interfacial adhesion energy increase from $1.38{\pm}1.06$ $J/m^2$ to $10.36{\pm}1.01$ $J/m^2$. The Ar+$H_2$ plasma treatment on Cu surface drastically increase the interfacial adhesion energy form $1.38{\pm}1.06$ $J/m^2$ to $6.59{\pm}0.03$ $J/m^2$. The plasma pre-treatment successfully reduces processing temperature of Cu to Cu direct bonding.

• Journal of the Korean institute of surface engineering
• /
• v.53 no.2
• /
• pp.43-52
• /
• 2020

Various aging treatments were conducted on AISI 630 martensitic precipitation hardening stainless steel in order to optimize aging condition. Aging treatment was carried out in the vacuum chamber of Ar gas with changing aging temperature from 380℃ to 430℃ and aging time from 2h to 8h at 400℃. After obtaining the optimized aging condition, several nitrocarburizing treatments were done without and with the aging treatment. Nitrocarburizing was performed on the samples with a gas mixture of H₂, N₂ and CH₄ for 15 h at vacuum pressure of 4.0 Torr and discharge voltage of 400V. The corrosion resistance was improved noticeably by combined process of aging and nitrocarburizing treatment, which is attributed to higher chromium and nitrogen content in the passive layer, as confirmed by XPS analysis. The optimized condition is finalized as, 4h aging at 400℃ and then subsequent nitrocarburizing at 400℃ with 25% nitrogen and 4% methane gas for 15h at vacuum pressure of 4.0 Torr and discharge voltage of 400V, resulting in the surface hardness of around 1300 HV_0.05 and α'_N layer thickness of around 11 ㎛ respectively.

• Korean Journal of Materials Research
• /
• v.8 no.2
• /
• pp.131-134
• /
• 1998

The deposition rate and surface morphology of Al films deposited by MOCVD have been studied on the $SiO_{2}$ and TiN(60nm/Si) substrates. A1 films were deposited with the pyrolysis of dimethylethylamine alane(DMEAA). When A1 was deposited on Ti& substrate without carrier gas, Al deposition rate increased with H\ulcorner pre- treatment. The $H_2$ gas enhances the CVD reaction at the substrate surface. When Al was deposited on $SiO_{2}$ substrate, $H_2$ plasma pretreatment reduced Al incubation time and made a dense Al film compared with Ar plasma pre- treatment or no pretreatment.

• Journal of the Korean Ceramic Society
• /
• v.49 no.6
• /
• pp.620-624
• /
• 2012

The role of moisture remaining inside the deposition chamber during the formation of the cubic boron nitride (c-BN) phase in BN film was investigated. BN films were deposited by an unbalanced magnetron sputtering (UBM) method. Single-crystal (001) Si wafers were used as substrates. A hexagonal boron nitride (h-BN) target was used as a sputter target which was connected to a 13.56 MHz radiofrequency electric power source at 400 W. The substrate was biased at -60 V using a 200 kHz high-frequency power supply. The deposition pressure was 0.27 Pa with a flow of Ar 18 sccm - $N_2$ 2 sccm mixed gas. The inside of the deposition chamber was maintained at a moisture level of 65% during the initial stage. The effects of the evacuation time, duration time of heating the substrate holder at $250^{\circ}C$ as well as the plasma treatment on the inside chamber wall on the formation of c-BN were studied. The effects of heating as well as the plasma treatment very effectively eliminated the moisture adsorbed on the chamber wall. A pre-deposition condition for the stable and repeatable deposition of c-BN is suggested.

• Journal of Ceramic Processing Research
• /
• v.21
• /
• pp.47-52
• /
• 2020

Graphene was synthesized using rapid thermal chemical vapor deposition (RT-CVD) equipment designed to produce largearea graphene at high speed. The effects of methane (CH₄), argon (Ar), and hydrogen (H₂) gases were investigated between 800 ℃ and 1,000 ℃ during heating and cooling in the graphene synthesis process. The findings reveal that multilayer domains increased due to hydrogen pretreatment with increase in temperature. Furthermore, when pretreated with the same gas, it was confirmed that the post-argon-treated sample cooled from 1,000 ℃ to 800 ℃ had a higher I_D/I_G value than that of the other samples. This result was consistent with the sheet resistance properties of graphene. The sample prepared in methane atmosphere maintained during both the pre-treatment and post-treatment demonstrated the lowest sheet resistance of 787.49 Ω/sq. Maintaining the methane gas atmosphere in the high-temperature region during graphene synthesis by RT-CVD reduced the defects and improved the electrical property.