• Title/Summary/Keyword: Ar purge gas

Search Result 7, Processing Time 0.021 seconds

Effects on the Al2O3 Thin Film by the Ar Pulse Time in the Atomic Layer Deposition (원자층 증착에 있어서 아르곤 펄스 시간이 Al2O3 박막에 미치는 효과)

  • Kim, Ki Rak;Cho, Eou Sik;Kwon, Sang Jik
    • Journal of the Semiconductor & Display Technology
    • /
    • v.20 no.4
    • /
    • pp.157-160
    • /
    • 2021
  • As an insulator for a thin film transistor(TFT) and an encapsulation material of organic light emitting diode(OLED), aluminum oxide (Al2O3) has been widely studied using several technologies. Especially, in spite of low deposition rate, atomic layer deposition (ALD) has been used as a process method of Al2O3 because of its low process temperature and self-limiting reaction. In the Al2O3 deposition by ALD method, Ar Purge had some crucial effects on the film properties. After reaction gas is injected as a formation of pulse, an inert argon(Ar) purge gas is injected for gas desorption. Therefore, the process parameter of Ar purge gas has an influence on the ALD deposited film quality. In this study, Al2O3 was deposited on glass substrate at a different Ar purge time and its structural characteristics were investigated and analyzed. From the results, the growth rate of Al2O3 was decreased as the Ar purge time increases. The surface roughness was also reduced with increasing Ar purge time. In order to obtain the high quality Al2O3 film, it was known that Ar purge times longer than 15 sec was necessary resulting in the self-limiting reaction.

A Study on the Welds Characteristics of Stainless Steel 316L Pipe using Orbital Welding Process (오비탈 용접법을 적용한 STS 316L 파이프 소재의 용접부 특성에 관한 연구)

  • Lee, B.W.;Joe, S.M.
    • Journal of Power System Engineering
    • /
    • v.14 no.2
    • /
    • pp.71-77
    • /
    • 2010
  • This paper was studied on microstructure, mechanical properties and corrosion characteristics of 316L stainless steel pipe welds was fabricated by orbital welding process. S-Ar specimen was fabricated by using Ar purge gas and S-$N_2$ specimen was fabricated by using $N_2$ purge gas. Ferrite was not detected in weld metal of S-$N_2$ specimen but the order of 0.13 Ferrite number(FN) was detected in weld metal of S-Ar specimen. Oxygen and Nitrogen concentration of S-$N_2$ specimen was higher than S-Ar specimen on HAZ and inner bead. The welds microstructural characteristics of S-Ar and S-$N_2$ specimens are similar. The microvickers hardness values of S-Ar and S-$N_2$ specimens welds were similar and average values of each regions were in the range of 174~194. The microstructures of S-Ar and S-$N_2$ weld metal were full austenite by primary austenite solidification. The Solidification structures of S-Ar and S-$N_2$ weld metal were formed directional dendrite toward bead center. The potentiodynamic polarization curve of STS 316L pipe welds exhibited typical active, passive, transpassive behaviour. Corrosion current density$(I_{corr.})$ and corrosion rate values of S-Ar specimen in 0.1M HCl solution were $0.95{\mu}A/cm^2$ and $0.31{\mu}A$/year respectively. The values of S-$N_2$ specimen were $1.4{\mu}A/cm^2$ and $0.45{\mu}m$/year.

Self-Limiting Growth of ZnO Thin Films and Substrate-Temperature Effects on Film Properties (자기제한적 표면반응에 의한 ZnO 박막성장 및 기판온도에 따른 박막특성)

  • Lee, D.H.;Kwon, S.R.;Lee, S.K.;Noh, S.J.
    • Journal of the Korean Vacuum Society
    • /
    • v.18 no.4
    • /
    • pp.296-301
    • /
    • 2009
  • An inductively coupled plasma assisted atomic layer deposition(ICP-ALD) system has been constructed for the deposition of ZnO thin films, and various experiments of ZnO thin films on p-type Si(100) substrates have been carried out to find the self-limiting reaction conditions for the ICP-ALD system under non-plasma circumstances. Diethyl zinc[$Zn(C_2H_5)_2$, DEZn] was used as the zinc precursor, $H_2O$ as the oxidant, and Ar as the carrier and purge gas. At the substrate temperature of $150^{\circ}C$, atomic layer deposition conditions based on self-limiting surface reaction were successfully obtained by series of experiments through the variation of exposure times for DEZn, $H_2O$, and Ar. ZnO deposition was repeated at different substrate temperatures of $90{\sim}210^{\circ}C$. As a result, the thermal process window(ALD window) for ZnO thin films was observed to be $110{\sim}190^{\circ}C$ and the average growth rate was measured to be constant of 0.29 nm/cycle. Properties of the film's microstructure and composition(Zn, O, etc.) were also studied. As the substrate temperature increases, the crystallinity was improved and ZnO(002) peak became dominant. The films deposited at all temperatures were high purity, and the films deposited at high temperatures had the composition ratio between Zn and O closer to one of a stable hexagonal wurtzite structure.

Construction of a PEALD System and Fabrication of Cobalt Thin Films (PEALD 장치 제작 및 Co박막 증착)

  • Lee, D.H.;Noh, S.J.
    • Journal of the Korean Vacuum Society
    • /
    • v.16 no.2
    • /
    • pp.110-115
    • /
    • 2007
  • A plasma enhanced atomic layer deposition(PEALD) system has been constructed adopting an inductively coupled plasma(ICP) source with an ALD system, and its plasma generation was carried out. Cobalt thin films were deposited on a p-type Si(100) wafer at $230^{\circ}C$. $Co_{2}(CO)_{6}$ was used as a cobalt precursor, $NH_{3}$ as a reactant, and Ar as a carrier and purge gas. The properties of the thin films were investigated using field emission scanning electron microscopy(FESEM) and auger electron spectroscopy(AES). Large amounts of impurities were found in both the ALD film and the PEALD film, however, the amount of impurities in the PEALD film was reduced to about 50 % compared to that in the ALD film. It was found that $NH_{3}$ plasma, very effectively, induces the reaction with carbon in a cobalt precursor.

A Study on Feasibility of the Phosphoric Acid Doping for Solar Cell Using Newly Atmospheric Pressure Plasma Source (새로운 대기압 플라즈마 소스를 이용한 결정질 실리콘 태양전지 인산 도핑 가능성에 관한 연구)

  • Cho, I-Hyun;Yun, Myoung-Soo;Jo, Tae-Hoon;Kwon, Gi-Chung
    • Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
    • /
    • v.27 no.6
    • /
    • pp.95-99
    • /
    • 2013
  • Furnace is currently the most important doping process using POCl3 in solar cell. However furnace need an expensive equipment cost and it has to purge a poisonous gas. Moreover, furnace typically difficult appling for selective emitters. In this study, we developed a new atmospheric pressure plasma source, in this procedure, we research the atmospheric pressure plasma doping that dopant is phosphoric acid($H_3PO_4$). Metal tube injected Ar gas was inputted 5 kV of a low frequency(scores of kHz) induced inverter, so plasma discharged at metal tube. We used the P type silicon wafer of solar cell. We regulated phosphoric acid($H_3PO_4$) concentration on 10% and plasma treatment time is 90 s, 150 s, we experiment that plasma current is 70 mA. We check the doping depth that 287 nm at 90 s and 621 nm at 150 s. We analysis and measurement the doping profile by using SIMS(Secondary Ion Mass Spectroscopy). We calculate and grasp the sheet resistance using conventional sheet resistance formula, so there are 240 Ohm/sq at 90 s and 212 Ohm/sq at 150 s. We analysis oxygen and nitrogen profile of concentration compared with furnace to check the doped defect of atmosphere.

Characteristics of Welds of Pure Titanium Plate Using Ultrasonic Attenuation (초음파 감쇠를 이용한 순 티타늄 판재의 용접부 특성)

  • Seon, Sang-Won;Yi, Won;Park, Hee-Dong;Hwang, Yeong-Tak
    • Journal of the Korean Society for Nondestructive Testing
    • /
    • v.33 no.2
    • /
    • pp.205-211
    • /
    • 2013
  • This paper studies on mechanical properties, fractures, and ultrasonic characteristics of Pure Titanium welds using ultrasonic attenuation. Ti specimen was made by using AR purge gas. When the titanium weld specimen is fractured, Tensile tests were conducted in order to observe the ultrasonic signal changes. A scanning electron microscope(SEM) was used to observe changes in failure surface and an ultrasonic normal probe with the central frequency of 4 MHz was used to obtain ultrasonic signals. As a result, the value of the mechanical properties in the weld zone was lower than that in the base zone and heat affected zone(HAZ) from Ti. Also the grain size in the weld zone was bigger than that in the weld zone and HAZ from Ti. Ultrasonic signals using a RMS method presents correlation between envelope area and the tensile strength. Consequently, the ultrasonic method could be potential tool for integrity evaluation of the Ti weld zone.

Coating of $TiO_2$ Thin Films on Glass Substrate using Photo-assisted Atomic Layer Deposition (광원자층증착법에 의한 glass 기판에 $TiO_2$ 박막 코팅)

  • Kim, Hyug-Jong;Kim, Hee-Gyu;Kim, Doe-Hyoung;Kang, In-Gu;Choi, Byung-Ho
    • 한국신재생에너지학회:학술대회논문집
    • /
    • 2009.11a
    • /
    • pp.382-382
    • /
    • 2009
  • 염료감응형 태양전지의 구성체 중 전극으로 연구 되어 지고 있는 $TiO_2$는 기존에 대량 생산이 가능한 spin coating법, screen printing법, spray법의 연구가 이루어져 왔으나 고 효율 태양전지에 쓰이는 전극 시스템에 비해 고 분산성을 지닌 $TiO_2$페이스트를 제조 하는데 어려움이 있다. 그리고 플렉시블 디스플레이 소자의 응용을 위해서는 소자 공정 온도인 $250^{\circ}C$ 이하의 공정 온도가 요구 되어 지므로 고온공정인 CVD법은 이에 적합하지 않다. 이에 본 연구는 진공 증착 방법인 광원자층증착법을 이용하여 $150^{\circ}C$이하의 저온공정온도에서도 적용이 가능한 $TiO_2$ 박막을 185nm의 UV light를 조사하여 glass 기판위에 제조 하고 그에 따른 박막의 물성 분석을 하였다. Mo source로는 titanium tetraisopropoxide(TTIP)와 reactant gas 로는 $H_2O$를 사용하였으며 불활성 기체인 Ar 가스는 purge 가스로 각각 사용하였다. $100^{\circ}C{\sim}250^{\circ}C$ 공정온도를 변수로 $TiO_2$ 박막을 제조 하였으며 제조된 $TiO_2$ 박막의 물성 분석을 위해 FESEM, TEM을 이용하여 표면 및 두께를 분석하였다. 또한 $100^{\circ}C$ 400 cycles에서 약 12nm 막 두께를 관찰 할 수 있었으며 그 결과 박막의 성장률이 $0.3{\AA}$/cycle 임을 확인 할 수 있었다. 그리고 UV-VIS을 이용하여 박막의 좌외선에 대한 흡수도 및 투과도 분석을 하였다. 또한 XPS 성분 분석을 통하여 $100^{\circ}C$의 저온 공정에서 형성된 박막이 $TiO_2$임을 확인 하였다. 이러한 결과에서 185nm의 UV light에 의한 광원자층 증착법으로 $100^{\circ}C$의 저온에서도 $TiO_2$ 박막이 증착 되는 것을 확인 할 수 있었다.

  • PDF