• Journal of the Korean Ceramic Society
• /
• v.34 no.1
• /
• pp.79-87
• /
• 1997

Anti-reflective and anti-static double layered films were prepared on the VDT panel by sol-gel spin-coating method. Their electrical, opticla, and mechanical properties were investigated. The outer SiO2 film with low re-fractive index was coated over the inner ATO(Antimony-doped Tin Oxide)-SiO2 film which was prepared by mixing ATO sol with SiO2 at molar ratio of 68:32 to satisfy the interference condition of double layers. The heat treatment was conducted at 45$0^{\circ}C$ for 30 min where residual organics were completely removed. The sheet resistance of ATO single layer showed the minimum value of 6$\times$107$\Omega$/$\square$ at 3 mol% addition of Sb and that of SiO2/ATO-SiO2 increased slightly with increasing SiO2 mol% up to 30 mol%, and then increased steeply to the value of 3$\times$108$\Omega$/$\square$ at 32 mol%. The reflectance of double layered films was about 0.64% at the wavelength of 550nm and the transmittance increased about 3.20%. The hardness of double layered films was almost the same as that of uncoated VDT panel, 471.4kg.f/mm2.

• Journal of the Korean Ceramic Society
• /
• v.31 no.8
• /
• pp.911-919
• /
• 1994

As the study for preparation of single-layer anti-reflective coating on glass, the conditions of synthesis of sol for coating and of reproducible coating procedure were investigated. In case of water-based sol, coating was impossible because of poor wettability of sol. The Substitution of solvent with ethanol improved the wettability of sol on the glass surface, and optimum amount of ethanol for substitution was 70 vol%. Maximum specific surface area and total pore volume of water-based sol were 268.7$m^2$/g and 0.315 cc/g, but after substitution, those values increased to 404.1 $m^2$/g and 0.376 cc/g, respectively. The upper limit withdrawl speed of coating in order to get clean coated films without aggregations or stains was 7 cm/min. In case of addition of 0.1 mol HNO3 and substitution with 70 vol% ethanol and heat-treatment at 40$0^{\circ}C$ for 1 hour, thin film with thickness of 94 nm was obtained at withdrawl speed of 4 cm/min. The thickness of thin film was independent of drying time.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.7.1-7.1
• /
• 2011

Nanoporous templates have been widely used for the development of new functional nanostructured materials suitable for electronics, optics, magnetism, and energy storage materials. We have prepared nanoporous templates by using thin films of mixtures of polystyrene-block-poly (methyl methacrylate) (PS-b-PMMA) and PMMA homopolymers. These templates have cylindrical nanoholes spanning the entire thickness of the film. Some applications of nanoporous templates are introduced: a) anti-reflective coating, b) the preparation of conducting polymer nanowires of poly (pyrrole), poly (3,4-ethylenedioxy-thiopene) onto a glass coated with indium-tin-oxide, and c) the separation membranes for biomaterials. We found that when the pore fraction of nanoholes in the film was ~0.68, almost zero reflectance at a specific wavelength, which can be changed with film thickness, was achieved at visible wavelengths Furthermore, ultra high density array of conducting nanowires was successfully prepared onto various substrates including flexible polymer. Due to highly alignment of polymer chain along the nanowire direction, the conductivity was much increased. Furthermore, these nanoporous films were found to be very effective for the separation of human Rhinovirus type 14 (HRV 14), major pathogen of a common cold in humans, from the buffer solution. We also found that when the pore size was effectively controlled down to 6 nm, a single file diffusion was observed.

• Journal of the Microelectronics and Packaging Society
• /
• v.23 no.2
• /
• pp.91-96
• /
• 2016

In this study, effects of demolding temperature (DT) on the formability and optical properties were evaluated in order to optimize thermal nanoimprint lithography for anti-reflective film. Characterization on optical property showed that optical performance was gradually enhanced as the DT increased up to $70^{\circ}C$ while the transmittance and the reflectance was degraded as the DT increased further to $100^{\circ}C$. In addition, similar behavior was observed from formability analysis. It was contributed to the formation of free volume and viscose flow. Therefore, it was concluded that the formability and optical property are highly influenced by the formation of free volume and viscous flow of polymer depending on the DT.

• Solar Energy
• /
• v.6 no.2
• /
• pp.70-75
• /
• 1986

The fabrication procedure and characteristics of $Ta_2O_5/Al/SiO_2/p-Si$ MIS solar cells forming a fine grating pattern of aluminum evaporated on to p-type silicon crystal are discribed. The proper temperature for oxide growing of these cells was found to be about $450^{\circ}C$ for 20 minutes with oxygen flow. The conversion efficiency increased about 3% after $750{\AA}$ thickness of tantalium silica film spin on anti-reflective coating. The best results showed that $V_{oc}=0.545V,\;J_{sc}=34mA$ and F.F = 0.65, which represent that the conversion efficiency is 12%.

• Journal of the Korean Vacuum Society
• /
• v.8 no.4A
• /
• pp.490-495
• /
• 1999

In 0.18 $\mu \textrm m$ LOGIC device, the etch rate of NMOS polysilicons is different from that of PMOS polysilicons due to the state of polysilicon to manufacture gate line. To control the etch profile, we tested the ratio of $Cl_2$/HBr gas and the total chamber pressure, and also we reduced Back He pressure to get the vertical profile. In the case of manufacturing the gate photoresist line, we used Bottom Anti-Reflective Coating (BARC) to protect refrection of light. As a result we found that $CF_4O_2$ gas is good to etch BARC, because of high selectivity and good photoresist line profile after etching BARC. in the results of the characterization of plasma damage to the antenna effect of gate oxide, NO type thin film(growing gate oxide in 0, ambient followed by an NO anneal) is better than wet type thin film(growing gate oxide in $0_2+H_2$ ambient).

• Journal of the Korean Vacuum Society
• /
• v.21 no.1
• /
• pp.55-61
• /
• 2012

We fabricated a-Si:H thin-film solar cell using the two-dimensional (2D) periodic patterned glass substrate. The use of a 3D periodic texture rather than a randomly texture at surface of TCO can result in higher short circuit current densities ($J_{sc}$). In order to analyze the optical effect of patterning glasses, ray-tracing simulations were performed. Also, p-i-n cells were deposited on patterned glasses as substrate by PECVD. UV-Vis spectroscopy, light I-V measurement were carried out for the optoelectronic characterization. The anti-reflective and light-trapping performance of patterning glass substrate was investigated by a comparison of experimental results with numerical simulations.

• Journal of Korean Ophthalmic Optics Society
• /
• v.6 no.2
• /
• pp.31-35
• /
• 2001

The anti-reflective anti-static(ARAS) optical film Was designed using conducting layer $TiN_x$ by Essential Macleod program. From this results, [air ${TiN_x{\mid}SiO_2{\mid}$ glass] two layer shows wide-band AR coating in the wavelength range of 450~700 nm. The $TiN_x$ thin films were prepared on the glass substrate by RF(radio-freqency) magnetron sputtering apparatus from a Ti target in agaseous mixture of argon and nitrogen with the thickness of 7~10 nm. For the films obtained, the chemical binding energy of the films was investigated by x-ray photoelectron spectroscopy(XPS) in order to analyze the chemical nature and composition of the films. In addition, we investigated the relationship between the surface resistance and the chemical nature the sheet resistance and XPS depth profiling the chemical binding of the films.

• Journal of Korean Ophthalmic Optics Society
• /
• v.5 no.1
• /
• pp.7-11
• /
• 2000

The anti-reflective anti-static (ARAS) optical film is designed using absorbent materials such as ITO, $TiN_xW_y$, Ag by Essential Macleod program. [air ${\mid}TiN_xW_y{\mid}SiO_2{\mid}$ glass] two layer shows wide-band AR coating in the wavelength range of 450~700 nm. The reflectivity, transmittance of this coating are below 0.5%, about 75%, respectively. [air $SiO_2{\mid}TiO_2{\mid}SiO_2{\mid}$, ITO glass] layer can adjust reflectance of below 0.5% with above 97% transmittance. In the [air ${\mid}SiO_2{\mid}TiO_2{\mid}SiO_2{\mid}$ Ag glass] layer, the transmission can be controlled at above 96% with reflectance of 1~2%.

• Journal of the Korean Vacuum Society
• /
• v.21 no.1
• /
• pp.22-28
• /
• 2012

Transparent dye-sensitized solar cells have been widely investigated for the application to building integrated photovoltaic system. Thin film Si-based solar cells are emerging as a substitute for the dye-sensitized solar cells because their merits of well-established manufacturing processes. Since the selective transmitting layer transmits visible light and reflects infrared light, the solar cell efficiency increases with the introduction of the selective transmitting layer. In this work, AlTiO thin films were grown as the selective transmitting layer by cost-effective sputter deposition and their transmittances were improved by controlling deposition parameters.