• Journal of the Society of Naval Architects of Korea
• /
• v.57 no.3
• /
• pp.124-132
• /
• 2020

The purpose of this paper is to establish the basic procedure and method for selection of preferred anti-fouling paint considering economic analysis according to ship's speed loss based on ISO 19030 that has been published in 2016 to prescribe practical methods for measuring changes in ship specific hull and propeller performance. In this study, six (6) anti-fouling paint products have been assumed for alternatives with each target maximum average speed loss and carried out comparison of the alternatives and sensitivity analysis in assumed conditions for selection of the preferred alternative.

• Corrosion Science and Technology
• /
• v.13 no.1
• /
• pp.15-19
• /
• 2014

Recently, anti-fouling paints which does not include the poison components such as tin(Sn), copper(Cu) have been increasingly developed in order to inhibit the environmental contamination of the sea water. Moreover, the wear ratios of these anti-fouling paints are very important problem to prolong their life time in economical point of view. In this study, five types of anti-fouling paints as self polishing type were investigated on the relationship between their polarization characteristics and wear ratios. It was verified that there was apparently a good relationship between the wear ratio and polarization characteristics, for example, the wear ratio increased with increasing the impedance ratio, and increased or decreased with the corrosion potential shifting in the negative or positive direction respectively. In addition, the wear ratio decreased with decreasing the corrosion current density. Consequently, it is suggested that we can qualitatively expect the wear ratio by only measuring the polarization characteristics. Therefore, before the examination of the wear ratio was actually carried out in the field, the evaluation of polarization property in the laboratory may give a available reference data for their developments.

• Journal of the Society of Naval Architects of Korea
• /
• v.54 no.1
• /
• pp.71-81
• /
• 2017

In this study, a series of full-scale extrapolation procedures based on the Granville's similarity scaling method, which was employed by Schultz (2007), is modified and then applied to compare the resistance performance between two different anti-fouling coatings. As an analysis example, the low frictional AF coating based on a novel skin-friction reducing polymer named FDR-SPC (Frictional Drag Reduction Self-Polishing Copolymer), which had been invented by the present author, is employed. The low frictional coating, which gives 25.4% skin frictional reduction in lab test, is estimated to give 18.2% total resistance reduction for a 176k DWT bulk carrier.

• Proceedings of KOSOMES biannual meeting
• /
• 2007.11a
• /
• pp.35-41
• /
• 2007

An International Convention on the control of harmful anti-fouling system on ships(AFS Convention) was adopted on 5 October 2001 at Diplomatic Conference in London, and is expected to be presently effectuated with ratification of more than 25-member nations possessing about 25% of total world tonnage. This convention regulates the operation of harmful anti-fouling system and especially prohibits the use of organotin compounds contained in anti-fouling paint. Organotin compounds have a tendency to be easily extracted by specific solvents and have high polarity and low volatility as specific characteristics. This drives us to attempt of going through the process named derivatization that is required in analysis using a gas chromatography(GC). This study was conducted to determine the proper pre-treatment method, ethylation in comparison with hydridization on the analysis of tributyltin in organotin compounds and to verify the application of the method through the experimental analysis practically used anti-fouling paint and painted layer sample of the served ship.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2002.11a
• /
• pp.39-44
• /
• 2002

Bans on TBT based antifouling paints have been drafted since 1999 by meetings 42, 43, 45 and 46 for the MEPC (Marine Environmental Protection Committee) of the International Marine Organization, and decided finally at a Diplomatic Conference of the IMO in October 2001. It was a key issue that there should be a global prohibition on the application of organo-tin compounds as biocides in Anti-fouling systems by Jan. 2003, and a complete prohibition on te presence of organo-tin compounds on ships by 1 Jan. 2008. This paper suggests a method to design International Anfi-fouling system cretificate, Record of anti-fouling system, Endorsement of the Records, Declaration on Anti-fouling System, Port State Control and reform(legislative) associated a law.

• Proceedings of KOSOMES biannual meeting
• /
• 2017.04a
• /
• pp.168-168
• /
• 2017

• Journal of the Society of Naval Architects of Korea
• /
• v.53 no.5
• /
• pp.400-409
• /
• 2016

In recent, shipping companies have made an enormous effort to improve the operation of vessel in various approaches, due to recession of shipping market and increasing competition among shipping companies. One of important parameters for improving the efficiency of vessel is the resistance performance that consist of friction and residual resistance. Especially, it is recognized that the friction resistance tends to be affected by conditions of vessel’s surface and occupies approximately 70~90% of the total resistance for slow speed ships. In general, the surface of vessel is covered with various type of paint to reduce fouling and corrosion. As time goes by, however, it is so hull roughness would be increased by fouling over the wetted surface that anti-fouling paints, such as CDP(Controlled Depletion Paint), Tin-Free SPC(Self Polishing Co-polymer) or Foul Release, are applied evenly on the hull surface. Nevertheless, these anti-fouling paints could not prevent fouling absolutely. A fundamental study on evaluating ship resistance performance variation due to hull roughness has been performed using a commercial software, Star-CCM+, which solves the continuity and Navier-Stokes equations for incompressible and viscous flow. The results of present simulation for plate are compared with some experimental data available and the effect of surface roughness to ship resistance performance is discussed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.6
• /
• pp.654-661
• /
• 2005

Copper is a well known alloying element that is used to improve the resistance to general corrosion of stainless steel And also Cu cation have the anti-fouling effect to inhibit adhesion of the marine algae and shellfish to the surface of heat exchanger cooling pipe or outside wall of the ship, Therefore there are some anti-fouling methods such as anti-fouling Paint mixed with copper oxide or MGPS(Marine Growth Preventing System) by using Cu cation dissolved to the sea wather solution. Cu cation can be dissolved spontaneously by galvanic current due to Potential difference between Cu and cooling pipe of heat exchanger with Ti material, which may be one of the anti-fouling designs. In this study the effect of annealing heat treatment to galvanic current and Polarization behavior was investigated with a electrochemical points of view such as measurement of corrosion Potential, anodic polarization curve. cyclic voltammetric curve, galvanic current etc The grain size of the surface in annealed at $700^{\circ}C$ was the smallest than that of other annealing temperatures. and also the corrosion Potential showed more positive potential than other annealing temperatures. The galvanic current between Ti and Cu with annealed at $700^{\circ}C$ was the largest value in the case of static condition. However its value in the case of flow condition was the smallest than the other temperatures. Therefore in order to increase anti-fouling effect by Cu cation, the optimum annealing temperature in static condition of sea water is $700^{\circ}C$, however non- heat treated specimen in the case of flow condition may be desirable.

• Journal of Korean Society for Atmospheric Environment
• /
• v.30 no.6
• /
• pp.569-576
• /
• 2014

In this research, a few paints in the shipyard were selected and analyzed for the component and ozone production in marine paint using TVOC and GC/FID, ozone generation index (MIR, POCP) to establish measures of $VOC_s$ effectively. The concentrations of TVOC ranged between approximately 300~400 g/L and 400~500 g/L, respectively and these showed 37% of whole. Our results indicated that the main constituents of marine paints were m,p,oxylene (49%), ethyl benzene (10%), toluene (8%) and 2-propanol (5%). It was also found that xylene concentration have relatively higher impact on ozone generation. The types of paints were also investigated for their potentials. The biggest contributor was the 1 Pack Finish paint. The rest is, in their contributing order, 1 Pack Finish paint, 2 pack Finish paint, Anti-fouling paint, 2 Pack A/C paint, Ballast paint and 1 Pack A/C paint.

• Polymer(Korea)
• /
• v.39 no.1
• /
• pp.122-129
• /
• 2015

Recently, the development of a new class of anti-fouling paint resin which has excellent anti-fouling performance and no persistence in the marine ecology is necessary. In this study, we first polymerized polyurethanes (PUs) as the other type of matrix which have carboxylic acid groups by using poly(ethylene glycol) (PEG), 4,4'-diphenylmethane diisocyanate (MDI), and 2,2'-bis(hydroxyl methyl)-propionic acid (DMPA). And next, we synthesized final resins having quaternary ammonium salts on pendant acid groups of PUs. After synthesis, the physical self-polishing property of resin by the measurement of reduced thickness in sea water was tested. The mechanical property of antifouling paint resin was good when the molecular weight of PEG was 600 or less. It was confirmed that the adhesion of PU resin was deteriorated when the content of quaternary ammonium salt was incorporated over specific value.