• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.17 no.9
• /
• pp.918-926
• /
• 1992

In this paper, ferrite-core loop antenna for portable radio receiver is designed and its characteristics are analyzed. Antenna is fabricated by inserting the ferrite core inside the planar conductor loop$(10{\times}6{\times}15mm^3)$. Bandwidth and Q factor of fabricated antenna measure 0.55 MHz and 280, respectively. These results show remarkable enhancement compared to the conventional loop antenna having the same physical dimension(BW=1.9MHz, Q=8.14). Experimental results show that the relative gain of the fabricated antenna is about 11 dB higher than that of the conventional antenna.

• Journal of Digital Convergence
• /
• v.15 no.4
• /
• pp.275-284
• /
• 2017

TACAN(TACtical Air Navigation) was created to support military aircraft's short range navigation (200~300 mile). TACAN must fulfill a condition of MIL-STD-291C, the U.S. Military Standards, which addresses the sum of 15Hz and 135Hz should be within 55%, following the factor of modulations for both to be $21{\pm}9%$ each. Within the existing TACAN antenna, modulation factor for 15Hz and 135Hz are created differently depending on its diameter, wavelength, angle of gradient, internal modulation method or using frequency code. It brings up a problem where applications needed to be stopped and repaired when modulating signal exceeds the standard of MIL-STD-291C since the existing TACAN antenna does not have coordination function. Hence, plan and produce a modulating signal generator using FPGA, and check the changes in the modulation factor for 15HZ and 135Hz, depending on the values that have been set in each criteria. Moreover, allow the modulating signal generator to be automatically adjusted based on the monitoring signal emitted by antenna, and place alarm sound just in case if it exceeds the standard.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.6
• /
• pp.1057-1062
• /
• 2016

In this paper, a design method for a compact log-perio dic half-bow-tie dipole array antenna for an operation in a UWB band(3.1-10.6 GHz) is studied. The proposed antenna is miniaturized by using half-bow-tie shaped dipole elements instead of strip-type dipole elements, which are commonly used in a general log-periodic dipole array(LPDA) antenna, and by reducing the element spacing. The effects of the flare angle of the half-bow-tie elements and the spacing factor on input reflection coefficient and realized gain characteristics of the proposed log-periodic antenna are analyzed. The optimized antenna is fabricated on an FR4 substrate, and the experiment results show that the antenna has a frequency band of 2.95-11.31 GHz for a VSWR < 2, which assures the operation in the UWB band. In addition, the length and width of the proposed antenna are reduced to 32.1 % and 18.3 %, respectively, compared to the LPDA antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.2
• /
• pp.208-216
• /
• 2002

In this paper, the design method of a waveguide broad-wall longitudinal slot array monopulse antenna of X-type monopulse axes is presented, and the method is verified through manufacture and measurement. In the antenna design of this paper, the antenna size is small and the monopulse axes are X-type. Thus, the common continuous aperture distribution fuction is not suitable and the power balance among antenna quadrants should be considered. Also, since the waveguide height is reduced into 0.1 wavelength, the modelling of the slot characteristics is not simple. Thus, in this paper, the aperture distribution is optimized by using random number, and the balance among the quadrants is achieved by applying the quadrant weighting factor during the aperture optimization process. Also, the moment method procedure is accelerated by applying the interpolation technique to some part of the moment matrix, and the moment method procedure is added to the array synthesis program as a subroutine so that the slot characteristics can be calculated directly when it is required. Based on this method, a antenna of 28dBi is designed and manufactured. It is found that the antenna characteristics is similar to design data.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.05a
• /
• pp.83-84
• /
• 2016

A wideband stacked patch antenna with parasitic elements, rectangular and triangle shaped patches, is proposed. Two different shaped parasitic elements are placed in the above of main rectangular microstrip patch antenna in order to achieve wide bandwidth for 860 MHz band. Coupling between the main patch and parasitic patches is realized by thick air gap. The gap and locations of parasitic patches are found to be the main factor of the wideband impedance matching. The proposed antenna is designed on a ground plane with small size of $119mm{\times}109mm$ for application of compact transceivers. And the impedance bandwidth of the antenna should satisfied CDMA band to the 780MHz~890MHz.

• ETRI Journal
• /
• v.33 no.2
• /
• pp.291-294
• /
• 2011

This letter proposes an open-ended waveguide antenna with a single split-ring resonator. In contrast to the waveguide antennas incorporating multiple rings reported in a previous study, which exhibited narrow bandwidth, the proposed antenna uses only one ring to achieve broader bandwidth while keeping the aperture small. A single ring has a relatively low quality factor compared to multiple rings. The simulated and measured fractional bandwidth was 4.13% and 4.03%, respectively, which is much broader than the fractional bandwidth of about 1% demonstrated in a previous study. This simple technique can be used in many applications that require small apertures including near-field probes and array elements.

• Proceedings of the Optical Society of Korea Conference
• /
• 1989.02a
• /
• pp.152-156
• /
• 1989

Parameters of a microstrip patch antenna such as the resonant frequency, radiation conductance, and the bandwidth are calculated. The rectangular microstrip patch antenna fed by a microstrip transmission line is fabricated and its resonant frequency, radiation pattern, and input voltage standing wave ratio are measured. The measured resonant frequency for 13.0mm$\times$9.7mm copper clad woven PTFE/glass laminate plate is 9.06Ghz, where the calculative is 9.00Ghz. And the measured vswr shows that the bandwidth of the antenna is 225MHz for vswr less then 2.0 which the calculated quality factor of the patch gives the bandwidth OF 280ghZ. The measured radiation pattern for 5 element as well as 4 element patch array shows less then 4dB deviation in the first side lobes from the designed values for both E and H plane pattern. This diviation is believed to be the power division errors of the power divider.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.10
• /
• pp.1184-1193
• /
• 2010

The upper frequency of international EMC regulations is being expanded above 1 GHz. Radiated emissions above 1 GHz are different from those below 1 GHz that is existing upper regulation frequency, and which have lower field strength and sharper and tilted beam-width, relatively. In this paper, an effective evaluation method to be used above 1 GHz is studied using an offset parabola antenna system having a double-ridged horn antenna as a feed. First, simple model is proposed for calculating antenna factor and field uniformity of the parabola antenna system, and then real radiated emission and radiated susceptibility measurements are performed using a constant noise emitter and the suggested antenna system. The results show that the proposed antenna system has higher gain and power efficiency, and wider field uniformity relative to a conventional double-ridged horn antenna. Therefore, it is confirmed that the proposed system can be effectively used for EMC measurements above 1 GHz.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.6 s.324
• /
• pp.93-99
• /
• 2004

According to rapid increment of demand for wireless Local Area Network (LAN), the HyperLAN of 5.1-533GHz and 5.725-5.825GHz is newly allocated for wireless LAM in many regions over the world. Also, because most of mobile communication equipments are small, the size of antenna is important factor of effective design. In this paper, the compacted and wide bandwidth antenna is designed for wireless LAN at 5GHz band. Although the structure of U-shaped slot antenna is simple, It has large bandwidth of $10-40\%$. Also, the U-slot antenna has good radiation pattern. However, in general, the size of U-slot antenna is large. Therefore, it is difficult to apply to wireless equipment such as PDA and Notebook. This proposed antenna has a wide bandwidth by U-shaped slot in rectangular patch and is compacted by using two layered dielectric substrates and foam. For the design of U-slot antenna, the Finite Difference Time Domain method is applied. Also, the method of MPI parallel program is used for the enhancement of the analyzing speed of the FDTD method.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.11
• /
• pp.1095-1103
• /
• 2014

WBAN has received great attention recently due to its versatile applicability. In this paper, antennas suitable for WBAN communication depending on the locations of mobile devices and the manufacturing of a human equivalent phantom are introduced. The effect of the body on the communication performance is largely dependent on the locations of devices. Specifically, the radiation and return loss characteristics of the antenna are greatly influenced by the characteristics of a medium existing in the near-field of an antenna. Thus, the proper WBAN antenna design is important in establishing a successful communication link between the transceivers. To consider the effect of the body on the antenna performance, the human equivalent phantom is also important factor in the WBAN antenna design and measurement. In introduction, categorization of the WBAN communication channel is introduced and antenna characteristics required for each communication channel are described. In the main subject section, several WBAN antenna design examples along with the implementation of the human equivalent phantom are discussed. In conclusion, the factors, which have to be considered in the design process, and future research are mentioned.