• 제어로봇시스템학회논문지
• /
• 제20권11호
• /
• pp.1164-1169
• /
• 2014

This paper proposes an angle estimation of Segway robot for the slop driving. Most of Segway robot was controlled by pose control of keeping robot's balance and motor control of driving. In motor control, we analyzed Segway robot kinetically and estimated an angle of inclination using the velocity that depends on input force. In pose control, also, we used PD controller and evaluated a stability of controller through MATLAB simulation. Assuming the robot keeps its balance stably using controller, we could linearize dynamics. We could obtain the result through the experiment which estimates an angle using the velocity of Segway robot that is derived from linearized dynamics.

• KIEAE Journal
• /
• 제14권1호
• /
• pp.15-22
• /
• 2014

Among the various building envelope elements, the glass area takes up the largest portion in the office building design. However, a large area of glass can cause problems such as excessive solar radiation, thermal comfort, and glare. Thus it is important to install the glass area to an appropriate level, and control solar radiation and inflow of daylight with blind devices. This study aims to improve the visual performance of the work plane through the automatic control of the venetian blinds. A total of eight kinds of control strategies were chosen; Case 1 does not control the blinds, Case 2 with the blind slats fixed at the angle of 0 degree, Case 3 to 6 using the existing blind control programs, and Case 7 and 8 with improved blind control. Case 3 with 90 degrees had the best energy performance, but the average indoor illuminance was 113lux, which is below the standards. Cases 4 and 5 showed higher levels of interior daylight illuminance with the average of 281lux and 403lux respectively. However, the fixed angles may have difficulties controlling excessive direct sunlight coming into the room and may cause glare. Cases 6 and 7 used sun tracking angle control and cut-off angle control, and the average interior illuminance was measured 250lux and 385lux respectively. Case 8 used the cut-off angle control in an hourly manner, satisfying the standard illuminance of 400lux with an average interior illuminance of 561lux. It was evaluated to be the best method to control direct solar radiation and to guarantee proper level of interior illumination.

• 한국추진공학회지
• /
• 제19권3호
• /
• pp.54-64
• /
• 2015

본 논문에서는 DACS(Divert and Attitude Control System)를 장착한 KV(kill vehicle)의 비선형 가속도 조종루프 설계에 대해서 다룬다. ACS(Attitude Control System)는 받음각을 0으로 유지시키는 추력을 유발시키며, 받음각 제어를 위해 ACS를 제어명령으로 사용하는 궤환선형화 기반 비선형 받음각 조종루프를 제안한다. 받음각이 0인 조건에서는 비행경로각과 자세각이 일치하기 때문에 DCS(Divert Control System)는 유도루프에서 요구하는 측방향 가속도를 직접 생성하도록 제어한다. 이러한 방식에서는 추력에 의한 공력간섭 효과를 최소화 시킬 수 있으며, DCS와 ACS의 운용로직을 단순화 시킬 수 있다. 수치 시뮬레이션을 통해 제안한 기법의 성능을 검증한다.

• 한국해양공학회지
• /
• 제30권4호
• /
• pp.243-252
• /
• 2016

Conventionally, the static angle of attack and static elevator tests are carried out separately to estimate hydrodynamic stability derivatives of underwater vehicles. However, it is difficult to verify the interaction between the angle of attack and elevator angle in such cases. In this study, we perform a static elevator with angle of attack test where both the angle of attack and elevator angle are varied simultaneously. The experimental results show that the angle of attack has an influence on the elevator control force and that this tendency is dependent on the sense in which the angle of attack and elevator angle are varied. We predict level flight performance using hydrodynamic derivatives estimated through this experiment. The predictions considering the effect of angle of attack show good agreement with trials conducted in the open sea.

• 대한기계학회논문집A
• /
• 제21권2호
• /
• pp.297-304
• /
• 1997

This paper presents a systematic design method of an anti-swing control law for overhead cranes. A velocity servo system for the trolley of a crane is designed based on the dynamics of the trolley and its load. The velocity servo system compensates for the effects of load swing on the trolley dynamics so that the velocity servo is independent of load swing. The velocity servo system is used for the design of a position servo system for the trolley via the loop shaping method. The position servo system and the swing dynamics of the load are then used to design an angle control system for load swing based on the root locus method. The combined position servo and the angle control systems constitute the overall control system. In the presence of low frequency disturbances, the proposed control law guarantees accurate position control for the trolley and fast damping for load swing. Furthermore, the performance of the proposed control law is independent of the mass of the load. Experimental results on a prototype crane show the effectiveness of the proposed anti-swing control law.

• 대한기계학회논문집B
• /
• 제27권8호
• /
• pp.1042-1050
• /
• 2003

A heating flow discharged from a 4-way ceiling type indoor unit has been investigated to determine the design parameters for the optimal flow control. The flow was measured by a PIV(particle image velocimetry) system and an experimental model of 1/10 scale with a transparent room was devised by satisfying the Archimedes number. This similarity is generally used in cases where the forced convection has similar magnitude of the natural convection. To optimize the heating flow, several vane angles and vane control algorithms of cross and right angle controls were considered. Regarding the vane angle, experimental results show that 30$^{\circ}$is an optimal angle to avoid re-suction flows without significant increase in flow noise. Temperature distribution measured in the environmental chamber ensures the increased thermal comfort when compared to the case, 60$^{\circ}$angle. At the optimal angle, applying open/close control gives rise to more uniform distribution of the heating flow than without control. Especially, the cross-control seems to be satisfactory for thermal comfort.

• 한국인터넷방송통신학회논문지
• /
• 제23권4호
• /
• pp.143-148
• /
• 2023

SRM의 특성 중 비선형성으로 인해 최대토크 및 최소 토크 맥동 형성을 위한 적정 운전이 어렵다. 또한 고정 스위칭각 제어 때 속도 가변에 따른 토크 형성이 불안정하여 효율을 저하시키는 문제점을 가지고 있다. 따라서 속도 가변에 따른 능동적인 스위칭각 제어가 필요하다. 본 논문에서는 SRM의 비선형성으로 인한 문제점으로부터 선행각 (Advance angle)의 자동제어에 의한 토크 리플 저감과 이에 따른 출력 토크 향상에 의한 구동 성능개선을 위한 방법에 대해 모색하였다. 또한 히스테리시스 전류제어기 성능에 따른 스위칭 가변으로 인한 SRM의 최적 운전에 대해 살펴보았다.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제11B권4호
• /
• pp.185-192
• /
• 2001

In SRM drive, the ON·OFF angles of each phase switch should be accurately controlled in order to control the torque and speed stably. The accuracy of the switching angles is dependent upon the resolution of the encoder and the sampling period of the microprocessor, that are used to provide the information of the rotor position and to control the SRM power circuit, respectively. However, as the speed increases, the amount of the switching angle deviation from the preset values is also increased. Therefore, the low cost encoder suitable for the practical and stable SRM drive is proposed and the control algorithm to provide the switching signals using the simple digital logic circuit is also presented in this paper, As a result, a stable high speed SRM drive can be achieved by the high resolution switching angle control and it is verified from the experiments that the proposed encoder the logic controller can be a powerful candidate for the practical low cost SRM drive.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제53권11호
• /
• pp.753-759
• /
• 2004

This paper presents a modeling and simulation of a fuzzy controller for maximum power extraction of a grid-connected wind energy conversion system with a link of a rectifier and an inverter. It discusses the maximum power control algorithm for a wind turbine and proposes, in a graphical form, the relationships of wind turbine output, rotor speed, power coefficient, tip-speed ratio with wind speed when the wind turbine is operated under the maximum power control. The control objective is to always extract maximum power from wind and transfer the power to the utility by controlling both the pitch angle of the wind turbine blades and the inverter firing angle. Pitch control method is mechanically complicated, but the control performance is better than that of the stall regulation method. The simulation results performed on MATLAB will show the variation of generator's rotor angle and rotor speed, pitch angle, and generator output.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권6호
• /
• pp.450-456
• /
• 2000

In this paper, we proposed a novel control method which uses the internal impedance angles as a control parameter to drive traveling wave type ultrasonic motor. An impedance characteristic of the ultrasonic motor is obtained by analysis of the equivalent circuits including the external inductor used to generate the coupled resonance. The phase angle of internal impedance to achieve optimal control performance is derived. For the tracking of impedance angle, an information of phase difference is obtained from the applied voltage and current. The high speed phase difference detector is designed to monitor the phases of ultrasonic motor. The effectiveness of the proposed control scheme is clarified by experiments.