• Journal of the Korean Society of Safety
• /
• v.14 no.4
• /
• pp.71-77
• /
• 1999

Exposed gas pipeline in underground, especially subway construction site, has been continuously vibrated by vehicle above ground. Because this vibration can cause unexpected damages to pipeline, we had measured and analyzed the vibration. This paper presents results of the vibration analysis of exposed gas pipeline and the results are as follows. The major vertical vibration frequency of pipeline was about 13 Hz and the other frequency components disappeared when the vibration transmitted to I-beam and wire rope. Existence of wooden casement had not affect vibration of exposed gas pipeline. The results of modal analysis by experimental and analytical methods have good agreement and it is also shown that exposed pipeline has possibility of resonance at second mode.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1448-1450
• /
• 1994

The breakdown voltages of punchthrough-mode diodes with cylindrical junction are analytically calculated, The proposed method, which is based on th Gauss's law, estimates the lateral expansion of the depletion region as well as the electric field and the charge distribution. The proposed method is given in terms of epitaxial layer width, the epitaxial layer doping concentration, and curvature radius of the junction edge. The calculation results agree well with the MEDICI simulation results for various device parameters.

• Journal of KSNVE
• /
• v.11 no.2
• /
• pp.292-300
• /
• 2001

This research is concerned with the validation of the modeling technique and controller design for slewing beam structures. When cantilever beam rotates about axes perpendicular to the undeformed beam's longitudinal axis, it experiences inertial loading. Hence, the beam vibrates from the initial stage of slewing. In this paper, the analytical model for a single slewing flexible beam with surface bonded piezoelectric sensor and actuator is developed using the Hamilton's principle with discretization by the assumed mode method. Comparisons with the theoretical model are made based upon the frequency responses and time responses. A new factor called the coupling coefficient is introduced to incorporate the discrepancies between the theoretical and experimental results. The slewing is achieved by applying the PID control, which is found to be less sensitive to vibrations. The vibrations are controlled by PPF controller, which is found to be effective in suppressing residual vibrations after slewing. The vibrations occurred during slewing is difficult to control because the piezoceramic actuator is not powerful enough to overcome inertial loadings.

• Structural Engineering and Mechanics
• /
• v.35 no.2
• /
• pp.217-240
• /
• 2010

A semi-analytical method is presented for accurately prediction of the free vibration behavior of generally laminated composite plates with arbitrary boundary conditions. The method employs the technique of separation of spatial variables within Hamilton's principle to obtain the equations of motion, including two systems of coupled ordinary homogeneous differential equations. Subsequently, by applying the laminate constitutive relations into the resulting equations two sets of coupled ordinary differential equations with constant coefficients, in terms of displacements, are achieved. The obtained differential equations are solved for the natural frequencies and corresponding mode shapes, with the use of the exact state-space approach. The formulation is exploited in the framework of the first-order shear deformation theory to incorporate the effects of transverse shear deformation and rotary inertia. The efficiency and accuracy of the present method are demonstrated by obtaining solutions to a wide range of problems and comparing them with finite element analysis and previously published results.

• Structural Engineering and Mechanics
• /
• v.43 no.3
• /
• pp.337-347
• /
• 2012

In this study, Hamiltonian Approach (HA) is applied to analysis the nonlinear free vibration of beams. Two well-known examples are illustrated to show the efficiency of this method. One of them deals with the Nonlinear vibration of an electrostatically actuated microbeam and the other is the nonlinear vibrations of tapered beams. This new approach prepares us to achieve the beam's natural frequencies and mode shapes easily and a rapidly convergent sequence is obtained during the solution. The effects of the small parameters on the frequency of the beams are discussed. Some comparisons are conducted between the results obtained by the Hamiltonian Approach (HA) and numerical solutions using to illustrate the effectiveness and convenience of the proposed methods.

• Journal of Applied Biological Chemistry
• /
• v.57 no.1
• /
• pp.89-93
• /
• 2014

We aim to develop a simple method for simultaneous and quantitative determination of benzoic acid, caffeic acid and chlorogenic acid in seeds of Eriobotrya japonica. In addition, antibacterial effect of these three phenolic acids was examined. A basic method is performed on the high performance liquid chromatography system coupled to an UV-detector (230 nm) and reverse phase C-18 column ($4.6{\times}150mm$, $5{\mu}m$). Each phenolic acid was confirmed via liquid chromatography-mass spectrometry (MS)/MS system under the multiple-reaction monitoring with negative-ion electrospray ionization (ESI(-)) mode. It is demonstrated that the method was could be applied to samples for an analytical study of the phenolic acids. On the other hand, three phenolic acids in seeds of E. japonica exhibited antibacterial effect against several pathogenic bacteria. Of these, benzoic acid was found to have stronger antibacterial effect.

• Journal of the Korean Institute of Navigation
• /
• v.20 no.1
• /
• pp.47-58
• /
• 1996

The use of high tensile steel plates is increasing in the fabrication of ship and offshore structures. The main portion of ship structure is usually composed of stiffened plates. In these structures, plate buckling is one of the most important design criteria and buckling load may usually be obtained as an eigenvalue solution of the governing equations for the plate. To use the high tensile steel plate effectively, its thickness may become thin so that the occurrence of buckling is inevitable and design allowing plate buckling may be necessary. When the panel elastic buckling is allowed, it is necessary to get precise understandings about the post-buckling behaviour of thin plates. It is well known that a thin flat plate undergoes secondary buckling after initial buckling took place and the deflection of the initial buckling mode was developed. From this point of view, this paper discusses the post-buckling behaviour of thin plates under thrust including the secondary buckling phenomenon. Series of elastic large deflection analyses were performed on rectangular plates with aspect ratio 3.6 using the analytical method and the FEM.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.6
• /
• pp.441-449
• /
• 2000

Analysis, design and practical implementation of a single-stage electronic ballast for compact fluorecent lamps are presented in this paper. The proposed topology is based on a single-stage ballast which combines a boost converter and a half-bridge series resonant inverter. High power factor is achieved by using the boost semi-stage operating in discontinuous conduction mode, and inverter semi-stage operated above resonant frequency to provide zero voltage switching is employed to ballast the fluorescent lamp. Analytical and experimental results from the ballast system with 36W fluorescent lamps have demonstrated the feasibility of the proposed single-stage electronic ballast.

• International Journal of Knowledge Content Development & Technology
• /
• v.6 no.1
• /
• pp.41-68
• /
• 2016

This paper aims to analyze the function of database management systems from the perspective of librarians working in engineering institutions in Andhra Pradesh. Ninety-eight librarians from one hundred thirty engineering institutions participated in the study. The paper reveals that training by computer suppliers and software packages are the significant mode of acquiring DBMS skills by librarians; three-fourths of the librarians are postgraduate degree holders. Most colleges use database applications for automation purposes and content value. Electrical problems and untrained staff seem to be major constraints faced by respondents for managing library databases.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.74-77
• /
• 1998

We consider connection-oriented wireless cellular networks. These networks employ dedicated radio channels for the transmission of signaling information. A forward signaling channel is a common signaling channel assigned to carry the multiplexed stream of paging and channel allocation(virtual circuit allocation) packets from a base station to mobile stations. The delay levels experienced by paging and channel allocation packets have serious effect on the utilization level of the limited radio channel capacity. While a slotted mode operation is used to reduce the power consumption level at mobile stations, it may induce an increase in packet delay levels. In this paper, we thus consider a multiplexing scheme for paging and channel allocation packets under which slots are dynamically allocated for the paging packet transmission. For this dynamic scheme, we develop an analytical method for deriving the delay characteristics exhibited by paging and channel allocation packets, and investigate the effect of network parameters on the delay level by using this method.