• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.6
• /
• pp.133-139
• /
• 2011

Maintaining adequate sealing in engine cylinder head is a crucial factor in engine design. Failure of engine operations occurs mainly owing to the leaking by decreased sealing pressure. Reliability-robustness concept is applied to the engine cylinder head system. Deterministic way to obtain engineering solution in CAE industry may not consider the effects of noises and disturbances experienced during operation. However, analytical reliability-robustness concept may make possible to reduce the sensitivity of system with noise factors. Influences of design factors including noise factors would be predicted in analytical way. Optimized design may be obtained by shrinking variability and shifting to design target. Three-dimensional finite element analyses have been performed to apply analytical reliability-robustness concept.

• Journal of the korean Society of Automotive Engineers
• /
• v.10 no.2
• /
• pp.39-45
• /
• 1988

The analytical model of an engine mount system with six degrees of freedom is identified using the modal parameters obtained from the experimental modal analysis. The structural parameters, mass moment of inertia of the engine block and stiffness of the rubber mounts, of the engine mount system are determined by using the condition that the estimated model parameters should satisfy the corresponding eigenvalue problem. The simulated modal parameters of the identified analytical model are in good agreement with the measured modal parameters.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.89-95
• /
• 2003

We consider a problem of application of analytical redundancy to engine synchronization process of spark ignition engines, which is critical to timing for every ECU process including ignition and injection. The engine synchronization process we consider here is performed using the pulse signal obtained by the revolution of crankshaft trigger wheel (CTW) coupled to crank shaft. We propose a discrete-time linear model for the signal, for which we construct FDI (Fault Detection & Isolation) system consisting residual generator and threshold based on linear observer.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.6
• /
• pp.238-249
• /
• 1995

The gas pressure acting on the rings in internal combustion engine influences the friction and wear characteristics. Inter-ring pressure variation during engine operation results from cylinder gas flow through a piston-ring pack. The flow passages consist of ring end gaps and clearances between the ring and the piston groove. The gas flow in the clearance between the ring and the groove is directly affected by the axial motion of the ring in the groove. In this paper the asperity contact force is newly considered in the prediction of the clearence between the ring and the groove surface. This term must be taken into account physically in case that the clearance get narrow rather than asperity height between the ring and the groove surface. Finally, comparisons of calculated inter-ring gas pressures based on the analytical method are made with the measured ones. The agereement was found to be good below midium engine speed, 3000rpm. In order to obtain accurate analytical results to the extend of high rpm range, it is recommended to include oil ring motion as well as top and second ring in analytical model.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.3
• /
• pp.1-7
• /
• 2007

Torque fluctuation of an engine and angular velocity variation of a propeller shaft are the main excitation sources in a vehicle driveline. This paper presents the mechanism of these excitation sources. An equivalent model of the engine system and propeller shaft system is constructed to simulate the excitation phenomena. The analytical model contains the geometrical and dynamic mechanism. Combustion pressure of the cylinder is measured from dynamometer. The computer simulation is carried out by commercial program package. Results of the simulations show the characteristics of the torsional excitation source of the driveline.

• Analytical Science and Technology
• /
• v.21 no.3
• /
• pp.159-166
• /
• 2008

In this study, the characteristics of emulsified fuel and engine emissions were studied. Emulsified fuel which composed of water and diesel was manufactured by using homogenizer and ultrasonic generator. Engine emissions were studied whit engine dinamometer. In emulsified fuel, density and viscosity were increased with increasing water contents, but viscosity was decreased over 60% of water in emulsion fuel. The emulsion type of W/O changed to that of O/W over 60% of water in emulsion fuel. In the results of engine dinamometer test, NOx concentration and smoke density were reduced with increasing water contents in emulsified fuel but reciprocal in the case of THC, CO. Temperature and power were reduced with increasing water contents in emulsion fuel. In conclusion, it seemed that using emulsified fuel for diesel engine was effective for reducing NOx concentration and smoke density.

• Journal of the korean Society of Automotive Engineers
• /
• v.7 no.1
• /
• pp.48-54
• /
• 1985

One of the most probable reason of the apex seal damage in IR-2500 industrial Wankel (rotary) engine was believed to be the engine detonation. Both analytical and experimental studies were made with a view th find out engine detonation pressure. The stagnation detonation pressure $p_{03}$' was estimated based on the data from IR-2500 engine detonation tests, such as engine firing pressure, state of fresh charge at BDC and polytropic compression exponent. The estimated stagnation detonation pressure for the natural gas fueled IR-2500 engine was in excess of 3,700 psia. With natural gas liquid added to the natural gas the octane value of the fuel was lowered, thus, making the engine more prone to detonate. The estimated detonation pressure for the case with the mixed fuel was about 3,400 psia which was sufficiently high to break the apex seal. The subsequent engine lab tests performed on two identical engines with sole difference in the apex seal thickness between the two engines proved that the engine knock, in fact, was the villain of the apex seal failure.ilure.

• Structural Engineering and Mechanics
• /
• v.90 no.1
• /
• pp.97-106
• /
• 2024

This paper presents a significant contribution to aided design by conducting an analytical examination of geometric links with the aim of establishing criteria for assessing an analogy measure of the extrinsic geometric and kinematic characteristics of the Variable Compression Ratio (VCR) engine with a Geared Mechanism (GBCM) in comparison to the existing Fixed Compression Ratio (FCR) engine with a Standard-Reciprocating Crankshaft configuration. Employing a mechanical approach grounded in projective computational methods, a parametric study has been conducted to analyze the kinematic behavior and geometric transformations of the moving links. The findings indicate that in order to ensure equivalent extrinsic behavior and maintain consistent input-output performance between both engine types, precise adjustments of intrinsic geometric parameters are necessary. Specifically, for a VCR configuration compared to an FCR configuration, regardless of compression ratio and gearwheel radius, for the same crankshaft ratios and stroke lengths, it is imperative to halve lengths of connecting rods, and crank radius. These insights underscore the importance of meticulous parameter adjustment in achieving comparable performance across different engine configurations, offering valuable implications for design optimization.

• Bulletin of the Korean Space Science Society
• /
• 2004.10b
• /
• pp.285-289
• /
• 2004

An optimal interplanetary trajectory is presented for Human Outer Planet Exploration (HOPE) by using an advanced magnetoplasma spacecraft. A detailed optimization approach is formulated to utilize Variable Specific Impulse Magnetoplasma Rocket (VASIMR) engine with capabilities of variable specific impulse, variable engine efficiency, and engine on-off control. To design a round-trip trajectory for the mission, the characteristics of the spacecraft and its trajectories are analyzed. It is mainly illustrated that 30 MW powered spacecraft can make the mission possible in five-year round trip constraint around year 2045. The trajectories obtained in this study can be used for formulating an overall concept for the mission.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.11a
• /
• pp.86-87
• /
• 2005

The combustion characteristics of the D.I. diesel engine are largely dependent on the air-fuel ratio and the gas exchange process. The main factors are the shape of combustion chamber, fuel injection system, air flow inside the cylinder, intake air mass flow rate and so forth. Because these factors affect the combustion in a mutual and combined manner, it is very important to clearly understand the correlation of these factors in order to provide the combustion improvement plans. In this paper, we studied the performance and the gas exchange process of marine four-stroke engine using the engine cycle simulation. Also, we predicted briefly turbocharger engine matching.