• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.44 no.2
• /
• pp.115-123
• /
• 2021

A lot of sensor and control signals is generated by an industrial controller and related internet-of-things in discrete manufacturing system. The acquired signals are such records indicating whether several process operations have been correctly conducted or not in the system, therefore they are usually composed of binary numbers. For example, once a certain sensor turns on, the corresponding value is changed from 0 to 1, and it means the process is finished the previous operation and ready to conduct next operation. If an actuator starts to move, the corresponding value is changed from 0 to 1 and it indicates the corresponding operation is been conducting. Because traditional fault detection approaches are generally conducted with analog sensor signals and the signals show stationary during normal operation states, it is not simple to identify whether the manufacturing process works properly via conventional fault detection methods. However, digital control signals collected from a programmable logic controller continuously vary during normal process operation in order to show inherent sequence information which indicates the conducting operation tasks. Therefore, in this research, it is proposed to a recurrent neural network-based fault detection approach for considering sequential patterns in normal states of the manufacturing process. Using the constructed long short-term memory based fault detection, it is possible to predict the next control signals and detect faulty states by compared the predicted and real control signals in real-time. We validated and verified the proposed fault detection methods using digital control signals which are collected from a laser marking process, and the method provide good detection performance only using binary values.

• Journal of Convergence for Information Technology
• /
• v.11 no.3
• /
• pp.14-19
• /
• 2021

In this paper, a method of constructing an inverter circuit that can generate negative voltage required to operate an IT device in a stable using an inexpensive buck device is presented. To do this, the problem of constructing the inverter circuit using the existing buck device was examined, the principle that could prevent this problem was analyzed, and a circuit that could solve this problem was presented. In order to prove the effectiveness of the proposed method, the experimental circuit was constructed and the experiment was conducted. Compared to the operation of the inverter circuit by the existing overcurrent prevention circuit, it was confirmed that the stable operation was performed without an overcurrent phenomenon. Accordingly, it is expected that the performance of the circuit can be greatly improved while a number of peripheral devices for configuring the devices for processing various analog signals used in IT devices as a single power supply can be omitted.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.15 no.5
• /
• pp.335-342
• /
• 2022

In this paper, a single-bit 3rd-order feedforward delta sigma modulator is proposed for audio applications. The proposed modulator is based on a class-C inverter for low voltage and power applications. For the high-precision requirement, the class-C inverter with regulated cascode structure increases its DC gain and acts as a low-voltage subthreshold amplifier. The proposed Class-C inverter-based modulator is designed and simulated in 180-nm CMOS process. With no performance loss and a low supply voltage compatibility, the proposed class-C inverter-based switched-capacitor modulator achieves high power efficiency. This design achieves an signal-to-noise-and-distortion ratio (SNDR) of 93.9 dB, an signal-to-noise ratio (SNR) of 108 dB, an spurious-free dynamic range (SFDR) of 102 dB, and a dynamic range (DR) of 102 dB at a signal bandwidth of 20 kHz and a sampling frequency of 4 MHz, while only using 280 μW of power consumption from a 0.8-V power supply.

• Pediatric Gastroenterology, Hepatology & Nutrition
• /
• v.25 no.6
• /
• pp.500-509
• /
• 2022

Purpose: We compared the health-related quality of life (HRQOL) of children and adolescents with functional abdominal pain disorders (FAPDs) and organic abdominal pain disorders (ORGDs). Methods: This was a single-center, cross-sectional, observational study. The PedsQL 4.0 generic cores scales parent proxy-report was administered to parents/caregivers of 130 and 56 pediatric patients with FAPDs and ORGDs respectively on their first visit. The self-reported pain intensity in the patients was assessed using a visual analog scale (VAS) and facial affective scale (FAS). Results: Irritable bowel syndrome was the most prevalent FAPDs, and the most prevalent ORGDs were reflux esophagitis (41.1%) and gastritis associated with Helicobacter pylori (21.4%). There was no difference in HRQOL among patients diagnosed with ORGDs and FAPDs (p>0.05). Patients with ORGDs and FAPDs had lower HRQOL Scale scores than healthy Brazilian and American children's references, with a high proportion of children at risk for impaired HRQOL (p<0.0001). There was no difference in the VAS and the FAS scores between the ORGDs and the FAPDs. FAPDs had a higher prevalence of girls' and couples' disagreement (p<0.02), although poor school performance (p<0.0007) and bullying (p<0.01) were higher in patients with ORGD. Conclusion: This study revealed that there was a difference in impaired HRQOL between patients with ORGDs and FAPDs. Thus, considering the high prevalence of chronic abdominal pain in children, a well-founded treatment plan is necessary for a multidisciplinary cognitive-behavioral Pain management program.

• Journal of Sensor Science and Technology
• /
• v.32 no.2
• /
• pp.88-94
• /
• 2023

Recently, piezoelectric tactile sensors have garnered considerable attention in the field of texture recognition owing to their high sensitivity and high-frequency detection capability. Despite their remarkable potential, improving their mechanical flexibility to attach to complex surfaces remains challenging. In this study, we present a flexible piezoelectric sensor that can be bent to an extremely small radius of up to 2.5 mm and still maintain good electrical performance. The proposed sensor was fabricated by controlling the thickness that induces internal stress under external deformation. The fabricated piezoelectric sensor exhibited a high sensitivity of 9.3 nA/kPa ranging from 0 to 10 kPa and a wide frequency range of up to 1 kHz. To demonstrate real-time texture recognition by rubbing the surface of an object with our sensor, nine sets of fabric plates were prepared to reflect their material properties and surface roughness. To extract features of the objects from the detected sensing data, we converted the analog dataset to short-term Fourier transform images. Subsequently, texture recognition was performed using a convolutional neural network with a classification accuracy of 97%.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.3
• /
• pp.59-64
• /
• 2023

Fire and disaster broadcasting systems are divided into analog, digital, and network-based digital public address systems, and important specifications in network-based digital public address systems are low-latency audio, high sampling rate, and multi-channel input and output. In the past, it has been widely used to the AoE method for distinguishing based on the MAC address of the data link layer. However, this method has a problem of increasing complexity and cost. This proposal is an AoIP/UDP method, which allows communication to be easily distinguished by IP address without the need for a separate redundant network, so that the network can be freely used and configured, and cost can be reduced by reducing complexity. After implementing the AoIP/UDP method, the experimental results showed that the cost was improved with the equivalent performance with 2.66ms latency.

• Journal of The Korean Society of Integrative Medicine
• /
• v.11 no.4
• /
• pp.61-71
• /
• 2023

Purpose : Energy bars are increasingly popular among active individuals, yet their timing and nutrient combinations' impact on exercise adaptation remains unclear. This study aims to address this knowledge gap by investigating whether the combination of pre- and post-workout supplementation can synergistically enhance fitness and alleviate fatigue in trained CrossFit participants. Investigate if combining pre- and post-workout supplements can enhance fitness and blood lactate management in trained CrossFit participants, potentially improving exercise performance for this group. Methods : In a randomized crossover study, 20 trained CrossFit individuals (11 males, 9 females) completed thrice-weekly 60-minute CrossFit sessions for 3 weeks, with a one-week washout period. Participants were randomly assigned to either a chocolate bar group (CH, 45 g, 225 kcal) or an energy bar group (ES, 48 g, 238 kcal, with protein, caffeine, taurine, and BCAAs). For one week, participants consumed two bars of their assigned supplement five minutes before and after workouts. After a washout period, they switched supplements. Blood lactate levels and a visual analog scale (VAS) were assessed before, immediately after, and 30 minutes post-workout. Fitness tests (hand grip, broad jump, sit-ups) were conducted at baseline and 30 minutes post-final workout. Data were analyzed using two-way repeated measures ANOVA (p<.05), 95 % confidence intervals, and magnitude inferences. Results : Hand grip strength (t=-5.60, p=.000), broad jump (t=-3.43, p=.003) and sit up (t=-3.94, p=.001) were significantly increased in the ES group. Compared to CH group, there was a significant time and group interactions for blood lactate level (F=5.51, p=.008) and VAS(F=31.67, p=.000) in the ES group. Conclusion : Pre- and post-workout energy bar supplementation may have a beneficial effect on blood lactate clearance and fitness in trained CrossFit individual. The combination of proprietary supplements taken may provide benefits for removing the blood lactate during high-intensity functional exercise.

• Journal of Fashion Business
• /
• v.27 no.5
• /
• pp.93-107
• /
• 2023

This study aimed to design a knee brace with dry electrode EMS (Electrical Muscle Stimulation) for elite badminton players suffering from knee pain and assess its effectiveness in relieving pain and improving mobility. The assessment measured knee joint range of motion (ROM), Sargent jump height, and pain perception using a visual analog scale (VAS). Four experimental groups were established: stability, pain induction after 100 squats, muscle soreness induction with a regular knee brace, and muscle soreness induction with the EMS knee brace. The most suitable knee brace was selected from four samples to design the EMS knee brace. The conductive fabric was integrated into the inner surface of the knee brace to enhance EMS conductivity for the quadriceps muscles. Tensile strength tests showed that the dry electrode did not significantly affect the physical functionality of the knee brace.Regarding knee joint ROM and Sargent jump height, the EMS knee brace outperformed muscle soreness induction with a regular knee brace and wearing a standard knee brace. VAS measurements demonstrated that the EMS braces effectively alleviated pain perception in most cases. The results indicate the potential for developing EMS braces to alleviate pain and prevent injuries for athletes across various sports.

• The Korean journal of internal medicine
• /
• v.39 no.1
• /
• pp.86-94
• /
• 2024

Background/Aims: A catheter is inserted through the nasal cavity during high-resolution esophageal manometry (HRM), which may cause adverse events such as pain or epistaxis. Despite these possible safety considerations, studies on this subject are very limited. We aimed to investigate the usefulness of nasal cavity evaluation before HRM to reduce the risk of adverse events and test failure. Methods: Patients who underwent HRM after consultation with the ear-nose-throat department for nasal evaluation were retrospectively enrolled between December 2021 and May 2022. The included patients had a previous history of sinonasal disease or surgery or had subjective nasal discomfort. All patients answered the Sino-Nasal Outcome Test (SNOT-22) questionnaire, and subjective nasal discomfort was scored using a visual analog scale. Nasal endoscopy and acoustic rhinometry were performed for disease evaluation and volumetric assessment. Results: The analysis included 22 patients with a mean age of 58.9 years. The mean SNOT-22 score was 24.2, and 16 patients (72.7%) complained of subjective nasal obstruction. The HRM catheter was successfully inserted in 20 patients (90.9%), without any significant adverse events. The objective measurement outcomes of acoustic rhinometry and sinus endoscopy did not always correspond to subjective symptoms. Narrowed nasal airways unresponsive to decongestants were observed in two patients with failed catheter insertion. Conclusions: To reduce the risk of adverse events and test failure during HRM, a site-specific questionnaire to evaluate nasal obstruction might be helpful. When nasal obstruction is suspected, objective nasal cavity evaluation could be recommended for the safe and successful performance of HRM.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.12 s.354
• /
• pp.15-22
• /
• 2006

In this paper, 1.8V 8-bit 500MSPS Low-power CMOS Digital-to-Analog Converter(DAC) for UWB(Ultra Wide Band) Communication Systeme is proposed. The architecture of the DAC is based on a current steering 6+2 full matrix type which has low glitch and high linearity. In order to achieve a high speed and good performance, a current cell with a high output impedance and wide swing output range is designed. Further a thermometer decoder with same delay time and low-power switching decoder for high efficiency performance are proposed. The proposed DAC was implemented with TSMC 0.18um 1-poly 6-metal N-well CMOS technology. The measured SFDR was 49dB when the output frequency was 50MHz at 500MS/s sampling frequency. The measured INL and DNL were 0.9LSB and 0.3LSB respectively. The DAC power dissipation was 20mW and the effective chip area was $0.63mm^2$.