• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.6
• /
• pp.923-928
• /
• 1986

This paper describes the design and fabrication of a high performance digital tuning analog component integrated circuit that contains a television station detector and decoders(H and L types). When the comparator level sampling method is used, this integrated circuit can be used as a stable channel selector for an external circuit with very large signal variation. It has been fabricated using the SST bipolar standard process and its chip size is 2.2x2.1mm\ulcorner As a result, we have succeeded in fabricating the IC that satisfies the D.C characteristics, and the channel station detector and decoder function.

• The Journal of the Acoustical Society of Korea
• /
• v.18 no.2
• /
• pp.53-60
• /
• 1999

In this paper, it is proposed to a new architecture of CMOS IADC(Current-Mode Analog-to-Digital Converter) using 1.5-bit bit cell of which consists a CSH(Current-Mode Sample-and-Hold) and CCMP(Current-Mode Comparator). In order to guarantee the entire linearity of IADC, the CSH is designed to cancel CFT(Clock Feedthrough) whose resolution is to meet at the least 9-bit which is placed in the front-end of each bit cell. In the proposed IADC, digital correction logic is simplified and power consumption is reduced because bit cell of each stage needs two latch CCMP. Also, it is available for a mixed-mode integrated circuit because all of block is designed with only MOS transistor. With the HYUNDAI 0.8㎛ CMOS parameter, the HSPICE simulation results show that the proposed IADC can be operated at 20Ms/s with SNR of 43 dB with which is satisfied 7-bit resolution for input signal at 100 ㎑, and its power consumption is 27㎽.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.2
• /
• pp.100-105
• /
• 2010

In this paper, a FM radio receiver integrated circuit has been developed based on $0.5{\mu}m$ CMOS process for Zero-Crossing FM demodulator over the 88MHz to 108MHz band. The receiver is designed with the low-IF architecture, and includes Low Noise Amplifier(LNA), Down-Conversion Mixer, Phase Locked Loop(PLL), IF LPF, and a comparator. The measured results of the LNA and Mixer show that the conversion gain of 23.2 dB, the input PldB of -14 dBm, and the noise figure of 15 dB. The measured analog block of the LPF and comparator show the voltage gain of over 89 dB, and the IF LPF can configure the passband from 600KHz to 1.3MHz with 100KHz step through the internal control register banks. The designed FM radio receiver operates at 4.5V with the total current consumption of 15.3mA, so the total power consumption is about 68.85mW. The commercial FM radio has been successfully received.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.9 no.2
• /
• pp.85-90
• /
• 2009

This paper presents a single supply PLC SoC ASIC with a built-in analog Front-end circuit. To achieve the low power consumption along with low cost, this PLC SoC employs fully CMOS Analog Front End (AFE) and several LDO regulators (LDOs) to provide the internal power for Logic Core, DAC and Input/output Pad driver. The receiver part of the AFE consists of Pre-amplifier, Gain Amplifier and 1 bit Comparator. The transmitter part of the AFE consists of 10 bit Digital Analog Converter and Line Driver. This SoC is implemented with 0.18 ${\mu}m$ 1 Poly 5 Metal CMOS Process. The single supply voltage is 3.3 V and the internal powers are provided using LDOs. The total power consumption is below 30 mA at stand-by mode to meet the Eco-Design requirement. The die size is 3.2 $\times$ 2.8 $mm^{2}$.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.4
• /
• pp.395-404
• /
• 2016

A 6-bit 3.4 GS/s flash ADC in a 65 nm CMOS process is reported along with the proposed 4x time-domain interpolation technique which allows the reduction of the number of comparators from the conventional $2^N-1$ to $2^{N-2}$ in a N-bit flash ADC. The proposed scheme effectively achieves a 4x interpolation factor with simple SR-latches without extra clocking and calibration hardware overhead in the interpolated stage where only offset between the $2^{N-2}$ comparators needs to be calibrated. The offset in SR-latches is within ${\pm}0.5$ LSB in the reported ADC under a wide range of process, voltage supply, and temperature (PVT). The design considerations of the proposed technique are detailed in this paper. The prototype achieves 3.4 GS/s with 5.4-bit ENOB at Nyquist and consumes 12.6 mW power at 1 V supply, yielding a Walden FoM of 89 fJ/conversion-step.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.5
• /
• pp.485-490
• /
• 2004

This paper presents a new interpolation algorithm for measuring high resolution position information which is prepared to a nino servo control motor using analog quadrature encoder. In the past, there are large capacity of memory(ROM or RAM) and two high price and resolution A/D(Analog-to-Digital Converter) for sensing two quadrature signals from a analog sinusoidal encoder interpolation. But high resolution of position from sinusoidal encoder can be obtained by using only small capacity of memory, one A/D converter and comparator. Experimental results show that the proposed algorithm is useful for measuring high resolution position.

• Proceedings of the KIEE Conference
• /
• 2006.10c
• /
• pp.606-608
• /
• 2006

This paper describes a 8bit 10MS/s low power pipelined analog-to-digital converter(ADC). To reduce power consumption in proposed ADC, a high gain op-amp that consumes large power in MDAC(multiplying DAC) of conventional pipelined ADC is replaced with simple comparator and current sources. Moreover, differential charge transfer amplifier technique with latch in the sub-ADC reduces the power consumption to less than half compared with the conventional sub-ADC which use high speed comparator. The proposed ADC shows the power consumption of 1.8mW at supply voltage of 1.8V. This proposed ADC is suitable to apply to the portable display device. The circuit was implemented with 0.18um CMOS technology and the core size of circuit is 2.5mm${\times}$1mm.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.1
• /
• pp.129-134
• /
• 2014

This paper presents a 10-bit 10-MS/s asynchronous successive approximation register (SAR) analog-to-digital converter (ADC) which consists of a digital-to-analog converter (DAC), a SAR logic, and a comparator. The designed asynchronous SAR ADC with a rail-to-rail input range uses a binary weighted DAC using metal-oxide-metal (MOM) capacitor to improve sampling rate. The proposed 10-bit 10-MS/s asynchronous SAR ADC is fabricated using a 0.18-${\mu}m$ CMOS process and its active area is $0.103mm^2$. The power consumption is 0.37 mW when the voltage of supply is 1.1 V. The measured SNDR are 54.19 dB and 51.59 dB at the analog input frequency of 101.12 kHz and 5.12 MHz, respectively.

• Journal of IKEEE
• /
• v.25 no.1
• /
• pp.206-211
• /
• 2021

This paper proposes a Self-Reset Zero-Current Switching (ZCS) Circuit for thermoelectric energy harvesting. The Self-Reset ZCS circuit minimizes the operating current consumed by the voltage comparator, thereby reduces the power consumption of the energy harvesting circuit and improves the energy conversion efficiency by adding the self-reset function to the comparator. The Self-Reset ZCS circuit shows 3.4% of improvement in energy efficiency compared to the energy harvesting system with the conventional analog comparator ZCS for the output/input voltage ratio of 5.5 as a result of circuit simulation. The proposed circuit is useful for improving the performance of the wearable and bio-health-related harvesting circuits, where low-power and energy-efficient thermoelectric energy harvesting is needed.

• Journal of information and communication convergence engineering
• /
• v.6 no.1
• /
• pp.43-46
• /
• 2008

This paper proposes an advanced test circuit for detecting the connectivity between a drum ring of laser printer and PCB. The detection circuit of charge sharing is proposed, which minimizes the influences of internal parasitic capacitances. The test circuit is composed of precharge circuit, analog comparator, level shifter. Its functional operation is verified using $0.6{\mu}m$ 3.3V/40V CMOS process parameter by HSPICE. Access time is100ns. Layout of the drum contact test circuit is $465{\mu}m\;{\times}\;117{\mu}m$.