• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.1022-1027
• /
• 2002

This paper describes the fluttering characteristics of the upper pad in a tilting pad journal bearing(6-pad, LOP type) using a steam turbine. In order to investigate the phenomena of the upper pad fluttering experimentally, the absolute vibration of the upper pads the relative vibration between bearing and shaft and the circumferential distribution of the film thickness are measured under the different values of supply oil flow rate, shaft speed and bearing load. It can be known that the fluttering mechanism of the upper pads has a tendency of the self-excited vibration from the study of fluttering frequencies and amplitudes with the change of shaft speed. furthermore, it is observed that the incipient upper pad fluttering velocity is increased by the increase of oil supply flow rate and fluttering amplitude of the upper pads is increased by the decrease of the oil flow rate and by the increase of the bearing load.

• 환경영향평가
• /
• 제21권5호
• /
• pp.609-615
• /
• 2012

In recent years, the development of computer technique was possible to the simulation analysis of the structure caused by ground vibration. Generally, finite element method(FEM) has been used in these structural analysis. In this study, it was calculated to the vibration energy as measuring vibration waveform, and estimated about principal stress due to medium characteristics of the ground as processing dynamic analysis by the vibration energy. The results are as follows : Firstly, the principal stress distribution in all mediums was different due to a medium condition, and the principal stress at concrete medium was represented to difference due to physical characteristics. Secondly, the principal stress by time increasing was represented to maximum amplitude within 0.03 second. And also, the principal stress after maximum amplitude was very large at concrete medium, which was considered to be formed compression or tension range at a medium boundary. Thirdly, the variation of principal stress at concrete medium was represented in the order of RC medium, NC=H medium, NC=S medium. It was considered that the vibration energy propagated fast when a medium have a big elasticity and density.

• 복합신소재구조학회 논문집
• /
• 제6권2호
• /
• pp.97-104
• /
• 2015

Compared with a strong axial rigidity due to large intial tension, cable has a weak laterally flexural rigidity. A variety of dynamic loads such as traffic loads and wind loads etc. cause the cables to vibrate significantly and affect the mechanical properties and the performance of cables. Therefore, vibration reduction design is an urgent task to control the vibration of cable-supported bridges. Because a various kind of dampers have shown to reduce the amplitude and duration time of vibration of cable from measured date in field test, damper can be considered that it is effective device significantly to reduce the amplitude and duration time in vibration of cable. Vibration characteristics of cable can change according to manufacturing method and type of established form, and damper has been designed according to distribution of natural frequencies and vibration modes. In this study, numerical analysis is used to show the reduction effects of vibrations and present the design of damper for vibration reduction of cable.

• 천문학회보
• /
• 제37권1호
• /
• pp.91.2-91.2
• /
• 2012

Kokubun (1983) reported the local time variation of normalized amplitude of sudden commencement (SC) with a strong day-night asymmetry at geosynchronous orbit with 81 SC events. Further careful inspection of Kokubun's local time distribution reveals that the normalized SC amplitudes in the prenoon sector are larger than those in the postnoon sector. That is, there is a morning-afternoon asymmetry in the normalized SC amplitudes. Until now, however, there are no studies on this SC-associated morning-afternoon asymmetry at geosynchronous orbit. Motivated by this previous observation, we investigate a large data set (422 SC events in total) of geosynchronous SC observations and confirm that the geosynchronous SC amplitudes is larger in the morning sector than in the afternoon sector. This morning-asymmetry is probably caused by the enhancement of partial ring current, which is located in the premidnight sector, due to solar wind dynamic pressure increase. We also examine the latitudinal and seasonal variations of the normalized SC amplitude. We find that the SC-associated geosynchronous magnetic field perturbations are dependent on the magnetic latitude and season of the year. This may be due to the location of the magnetopause and cross-tail currents enhanced during SC interval with respect to geosynchronous spacecraft position.

• 한국공작기계학회논문집
• /
• 제14권1호
• /
• pp.30-36
• /
• 2005

This study is to investigate a damage estimation of single edge notched tensile specimens as a function of acoustic emission(AE) according to the uni-directionally oriented carbon fiber/epoxy composites, CFRP In fiber reinforced composite materials, AE signals due to several types of failure mechanisms are typically observed. These are due to fiber breakage, fiber pull-out matrix cracking, delamination, and splitting or fiber bundle breaking. And these are usually discriminated on the basis of amplitude distribution, event counts, and energy related parameters. In this case, AE signals were analyzed and classified 3 regions by AE event counts, energy and amplitude for corresponding applied load. Bath-tub curve shows 3 distinct periods during the lifetime of a single-edge-notch(SEN) specimen. The characterization of AE generated from CFRP during SEN tensile test is becoming an useful tool f3r the prediction of damage failure or/and failure mode analysis.

• 비파괴검사학회지
• /
• 제31권1호
• /
• pp.53-61
• /
• 2011

본 연구는 편측 노치가 삽입된 A16061-T6 알루미늄 합금 평판 시편에 대해 유리섬유강화플라스틱(GFRP) 복합재 패치의 적층수를 변수로 하여 보수히고, 인장 하중에 따른 시편의 손상 과정을 음향방출법(acoustic emission, AE)으로 실시간 분석하였다. AE 에너지 발생률(AE energy rate), hit 발생률(hit rate), AE 진폭(AE amplitude) 거통과 파형 및 1차 중심주파수(1st peak frequency)의 대역을 조사하여, 시편 파괴시 알루미늄 크랙(Al cracking), 섬유 파단(fiber breakage), 수지 균열(resin cracking), 층간 분리(delamination)로 분류하였다. 시편의 변위를 음향방출 특성에 따라 구간(region) I, II, III으로 나눌 수 있었으며, 패치 자체가 실제 파괴되는 구간인 구간 II를 세부적으로 분석하여 패치의 적층수에 따른 AE 특성 차이를 구하였다.

• 설비공학논문집
• /
• 제2권3호
• /
• pp.188-198
• /
• 1990

Turbulent characteristics of turbulent pulsating flows were studied experimentally in a square duct. Velocity waveforms, velocity profiles, and turbulent intensity of turbulent pulsating flow were investigated by using a hot-wire anemometer with data acquisition and a processing system in a square duct with a ratio of 1 ($40mm{\times}40mm$) to 4,000mm long. Turbulent components were shown to be larger in decelerating than in accelerating regions and also larger for a large phase of velocity and U'rms distribution of turbulent flow. The effect of velocity amplitude ratio does not exist for specified time [${\theta}(z^{\prime})$], amplitude ratio (${\mid}U^{\prime}_{rms.os.1}{\mid}/{\mid}U_{m.os.1}{\mid}$), and phase difference (${\Delta}U^{\prime}_{rms.os.1}-{\Delta}U_{m.os.1}$) in either turbulent oscillating or cross-sectional mean velocity components. The effect of dimensionless angular frequency for specified time [${\theta}(z^{\prime})$] can be disregarded because the dimensionless angular frequency does not affect the specified time. The velocity distributions of turbulent pulsating flows for various time-averaged Reynolds numbers are in approximate agreement with the velocity distributions for equivalent Reynolds numbers and 1/7th power law of steady flow.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2003년도 종합학술발표회 논문집 Vol.13 No.1
• /
• pp.8-12
• /
• 2003

To protect digital communications and broadcasting that are expected to be increasingly used at frequencies above 1GHz, there is a need to determine permissible disturbance limits for frequency bands above 1GHz according to indicates that better correlates with interference level in digital systems. The quality of digital communications is expressed in terms of bit error rate(BER) or throughput. In this regard, it has been reported that degradation of BER or throughput can be estimated from the amplitude probability distribution (APD) of disturbance amplitude. Therefore, if the APD can simply be measured with a high accuracy, APD will be an optimal index for the assessment of interference in digital communications. In this paper, we show that a measurement method using statistic model of APD has compatibility about performance reduction estimation of WLAN. And through approach of this inspection, we propose numeral models about interference effects of peak value and time rate of spurious.

• 한국재료학회지
• /
• 제13권10호
• /
• pp.651-657
• /
• 2003

Ultrasonic microscope has been used to detect the defects on surface or inner solid. Conventionally, it has used at a single operating frequency. The resolution and quality of the measured images are determined by a characteristic of the transducer of the ultrasonic microscope. The conventional ultrasonic microscope has been used envelope detector to detect the amplitude of reflected signal, but the changes in amplitude is not sensitive enough for specimen with microstructure that in phase. In this paper, we have studied multi-frequency depth resolution enhancement with ultrasonic reflection microscope for the reflectors of a stainless steel reference specimen and a reference calibration block to be used as the material in nuclear power plants for ISI, PSI. Increased depth resolution can be obtained by taking two, three-dimensional images at more that one frequency and numerically combining the results. As results of the experiment, we could get enhanced images with the rate of contrast in proportion and high quality signal distribution for the image to the changing rate of depth for the reflectors of the two kinds of specimens.

• 수산해양기술연구
• /
• 제44권2호
• /
• pp.148-156
• /
• 2008

In this study it will be discussed how to solve the problem of discomfort from rolling motion on the fishing boats. Most discomfort is caused by the short cycle of rolling due to the light weight of the boats. The light weight is due to the FRP material which dries a boat. A way to improve the feeling of boarding by using fish hold was researched. The experiment was done on experimental fishing boat made by FRP in Jeju. An existing fish hold was designed and manufactured through the rolling test and that was used for a marine experiment. The rolling condition of the U-tank boat ideally designed was compared to that of an existing fishing boat using the same conditions. The experiments were carried out two times on the stop engine in the outward Sehwa fishing port, which the experimental data had analysed for effects of rolling reduction to compare the U - tank with the of exiting fish hold. The results were confirmed that the U-boat tank in the roll period and GoM were more safe than the existing fish hold and the average amplitude and significant of rolling angles were decreased relatively.