• Journal of Applied Biological Chemistry
• /
• 제66권
• /
• pp.258-265
• /
• 2023

축산용 항생제는 투여된 양의 일부만이 체내에서 사용되며 나머지는 모화합물 형태나 대사체로서 분뇨를 통하여 배출된다. 이러한 분뇨는 자원화 시설로부터 퇴액비로 생산되어 농경지에 살포됨으로써 농업환경에 유입되어 2차 오염 등을 초래하고 있다. 본 연구는 국내 가축분뇨 자원화 시설의 액비 생산단계별로 6종 축산용 항생제의 잔류 농도를 비교하고 액비 성분 질소 함량과의 상관성을 평가하기 위해 수행되었다. Buffer 및 SPE를 사용한 전처리 방법은 ppb 수준에서 63.4-106.7%의 회수율을 나타냈으며, 정량한계의 범위는 0.009-0.037 ㎍/L이었다. 공동자원화 시설 생산 액비의 생산단계별 잔류 항생제 농도와 규격함량 N 성분 함량과의 상관성 평가를 분석한 결과 액비화 과정 중 부숙 기간이 경과함에 따라 N 성분 및 항생제 잔류 농도가 감소하는 경향을 보여 주었다. 액비 원료, 중기 및 제품 중 SMZ의 평균 잔류 항생제는 40.85, 26.17, 3.54 ㎍/L이었으며 CTC의 경우 2.32에서 1.25 ㎍/L 수준으로 감소하였다. 다른 4종 항생제 역시 생산단계별로 잔류 농도가 감소하는 경향을 보여주었으며 액비 규격성분 N은 생산단계별 함량이 0.21에서 0.096%로 감소하였다. 액비 생산단계별 잔류 항생제 농도와 규격 성분 N 함량과의 상관성 평가는 항생제 저감화 지표 설정의 기초자료로 활용 가능할 것으로 판단된다.

• KSBB Journal
• /
• 제13권6호
• /
• pp.675-680
• /
• 1998

In both 7L and 20L fermentor experiments the level of dissolved oxygen (D.O) strongly affected growth and PHBV production of Azotobacter vinelandii UWD. A higher D.O. increased carbon substrate consumption rate and cell growth rate with a similar residual biomass production. However, a lower D.O. was a much better condition for PHBV production. In a 20L fermentor experiments controlled at 5% D.O. cell growth rate was about twice faster(0.555 hr-1 and 0.260 hr-1 at the acid and the glucose phase, respectively) with an equal amount(4.5 g/L) of residual biomass production. However, PHBV content in the cell(62.3 wt%) increased 17.3 times at 1% D.O.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2010년도 춘계학술발표대회 초록집
• /
• pp.57-57
• /
• 2010

For thin panel welded structure, the various welding distortions were found due to the low resistance against welding deformation. Especially, buckling distortion induced in the thin panel welded structure produce severe problems related to cost in production stage and safety in service life. So, many researches including mechanical and thermal tensioning method for preventing the occurrence of buckling distortion in the production stage have been performed. The purpose of this study is to identify the behavior of longitudinal residual stress at the SA butt weldment with thin plate of 6mm thickness under tension load by 3 dimensional FEA. For it, mesh design for 3D FEA was constructed with 20 nodes brick element for butt weldment and 8 nodes shell element for base metal. According to FEA results, the longitudinal compressive strain inducing tensile residual stress at the butt weldment decreased. It was because the compressive thermal strain in way of weldment was reduced by tension load. The control effect of residual stress increased with an increase in tension load. So, if the amount of tension load applied to the weldment exceeds 1.5 times of longitudinal shrinkage force, the amount of longitudinal residual stress decreased below the critical value inducing the buckling distortion at the SA butt weldment. Its validity was verified by experiment.

• Design & Manufacturing
• /
• 제15권4호
• /
• pp.32-36
• /
• 2021

In this study, the cause of the decrease in transmittance of the outer lens among the causes of the decrease in the amount of light in the automobile headlamp was identified, and the improvement method was selected to determine the effect. The causes of defects that lower the transmittance of the outer lens are divided into a moisture problem and a haze problem. The moisture problem is caused by the temperature difference between the inside and the outside of the head lamp, and the haze problem occurs when the heat inside the head lamp evaporates the haze component contained in the plastic material and attaches it to the outer lens. In order to improve the haze problem that occurs in plastic raw materials, the structures of the bulb light source type headlamp and the LED chip light source type headlamp were analyzed. Among them, the housing material of the LED chip light source type headlamp, which is structurally prone to haze gas, was selected as the test target. In the mass-production injection process of the housing, the drying process was selected as a method to minimize haze gas without adding a separate production process. After extracting a sample every drying time at a constant drying temperature, the sample was put into a haze tester and the residual amount of haze gas was measured. As a result, it was confirmed that the residual amount of Haze gas in the material decreased as the drying time increased.

• Environmental Engineering Research
• /
• 제24권2호
• /
• pp.202-210
• /
• 2019

In order to maximize the utilization of sewage sludge, a waste from wastewater treatment facility, the residual sewage sludge generated after lipid and carbohydrate extraction for biodiesel and bioethanol production was used to produce bio-oil by pyrolysis. Thermogravimetric analysis showed that sludge pyrolysis mainly occurred between 200 and $550^{\circ}C$ (with peaks formed around 337.0 and $379.3^{\circ}C$) with the decomposition of the main components (carbohydrate, lipid, and protein). Bio-oil was produced using a micro-tubing reactor, and its yield (wt%, g-bio-oil/g-residual sewage sludge) increased with an increase in the reaction temperature and time. The maximum bio-oil yield of 33.3% was obtained after pyrolysis at $390^{\circ}C$ for 5 min, where the largest amount of energy was introduced into the reactor to break the bonds of organic compounds in the sludge. The main components of bio-oil were found to be trans-2-pentenoic acid and 2-methyl-2-pentenoic acid with the highest selectivity of 28.4% and 12.3%, respectively. The kinetic rate constants indicated that the predominant reaction pathway was sewage sludge to bio-oil ($0.1054min^{-1}$), and subsequently to gas ($0.0541min^{-1}$), rather than the direct conversion of sewage sludge to gas ($0.0318min^{-1}$).

• 소성∙가공
• /
• 제28권4호
• /
• pp.212-218
• /
• 2019

In this study, the first drawing die for the production of coil wedge is redesigned in order to enhance properties such as dimensional accuracy, dimensional uniformity, non-magnetism, and residual stress. The equivalent strain distribution is observed to be asymmetric at certain corners of the product and un-filling of material is also observed at the same location, based on the results of FEM simulation for the current drawing process. Additionally, a relatively huge amount of deformation is concentrated on the surface of the reference product leading to an increase in magnetic component and surface residual stress. After re-designing the cross-section of the first drawing step process conformed to relatively higher amount of reduction ratio, reduction of both surface residual stress and the volume fraction of magnetic component could be achieved for the finally-drawn coil wedge product.

• Asian-Australasian Journal of Animal Sciences
• /
• 제15권7호
• /
• pp.925-931
• /
• 2002

Gibbs sampling algorithms were implemented to the multi-trait threshold animal models with any combinations of multiple binary, ordered categorical, and linear traits and investigate the amount of bias on these models with two kinds of parameterization and algorithms for generating underlying liabilities. Statistical models which included additive genetic and residual effects as random and contemporary group effects as fixed were considered on the models using simulated data. The fully conditional posterior means of heritabilities and genetic (residual) correlations were calculated from 1,000 samples retained every 10th samples after 15,000 samples discarded as "burn-in" period. Under the models considered, several combinations of three traits with binary, multiple ordered categories, and continuous were analyzed. Five replicates were carried out. Estimates for heritabilities and genetic (residual) correlations as the posterior means were unbiased when underlying liabilities for a categorical trait were generated given by underlying liabilities of the other traits and threshold estimates were rescaled. Otherwise, when parameterizing threshold of zero and residual variance of one for binary traits, heritability estimates were inflated 7-10% upward. Genetic correlation estimates were biased upward if positively correlated and downward if negatively correlated when underling liabilities were generated without accounting for correlated traits on prior information. Residual correlation estimates were, consequently, much biased downward if positively correlated and upward if negatively correlated in that case. The more categorical trait had categories, the better mixing rate was shown.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2004년도 춘계학술발표회
• /
• pp.461-468
• /
• 2004

The amount of $CO_2$ and $CH_4$ that were produced during biodegradation with were measured as function of time. Also, the settlements of landfill lysimeters were measured at the same time, and the relation with LFF(landfill gas) production was investigated. The effects of leachate recycle on the acceleration of settlement were studied by comparing two lysimeters. The gas production rate constant, $^{\kappa}_{LFG}$ is obtained to predict future gas production and settlement. These will be key role factors to predict gas production patterns and residual long-term settlement.

• 한국산림과학회지
• /
• 제102권4호
• /
• pp.484-490
• /
• 2013

본 연구는 낙엽송 개체목의 가공처리 과정에서 생산되는 제재목 및 제재 부산물의 양을 분석하기 위한 시뮬레이션 모델을 개발하고자 수행되었다. 이 모델에서는 수간곡선 추정식을 이용하여 개체목의 전간재적을 산출하고 절동된 원목에 대한 목재 가공 시뮬레이션을 통해 판재 및 각재, 원주목의 규격에 따른 최대 생산가능량을 예측하였다. 또한 제재목 가공처리 과정에서 생산되는 톱밥 및 죽데기의 잔존재적에 대한 분석을 수행하였다. 그 결과 흉고직경 12 cm 이상부터 제재목의 생산이 가능한 것으로 나타났고, 제재목의 생산이 가능한 경우에는 보다 큰 규격의 판재와 각재를 생산하는 것이 상대적으로 작은 규격의 판재와 각재 혹은 원주목을 생산하는 것에 비해 더 많은 생산량을 얻을 수 있었다. 향후 이 모델은 낙엽송의 이용재적 산출을 통한 산림의 경제적 가치평가는 물론, 최근 목질계 바이오에너지 자원으로서 그 중요성이 점차 높아지고 있는 톱밥과 같은 제재 부산물의 양을 예측하는 데에도 활용될 수 있을 것이다.

• 한국환경과학회지
• /
• 제7권2호
• /
• pp.217-222
• /
• 1998

Organics matters including algae are the major contaminants of Nak-dong river and it's concentration Is more Increasing now. The use of coagulants has been Incresed for the effective treatment of drinking water, and aluminum coagulants have been the most widely used in raw water treatment. However, when inorganic metal coagulant is excessively used for long period, it would result in secondary problems, such as increasing sludge production, enhancing the cost of water treatment process, and increasing concentration of residual metal, especially aluminum. Therefore, recently. in order to reduce the use of metal coagulant and enhance the coagulation effectiveness, several alternative coagulants, such as polymeric Inorganic coagulants and organic polymers, have been used In water treatment plants. The objectives of thins research were (11 to determine optimum dosage concentration and compare the coajuiation efnciency at various pH ranees with alum alone, alum+cationic polymer, and alum+anlonlc polymer, (21 to evaluate the amount of alum reduced by using organic polymer, (31 to maximize removal officiency of organic matter and minimize the concentration of residual aluminum.