• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.1
• /
• pp.19-24
• /
• 2005

In this paper, the fabrication process of Si pressure sensors utilizing piezoresistive effect was optimized. The efficiency(yield) of the fabrication process for Si piezoresistive pressure sensors was improved by conducting Si anisotrophic etching process after processes of piezoresistors and AI circuit patterns. The position and process parameters for piezoresistors were determined by ANSYS and SUPREM simulators, respectively. The measured thickness of p-type Si piezoresistors from the boron depth-profile measurement was in good agreement with the simulated one from SUPREM simulation. The Si anisotrohic etching process for diaphragm was optimized by adding ammonium persulfate(AP) to tetramethyl ammonium hydroxide (TMAH) solution.

• Journal of the Semiconductor & Display Technology
• /
• v.2 no.4
• /
• pp.19-22
• /
• 2003

In this paper, Si anisotropic etching characteristics of tetramethylammonium hydroxide (TMAH)/ammonium persulfate (AP) solutions were investigated to realize the optimum structure of a diaphragm for the piezoresistive pressure sensor application. Due to its low toxicity and its high compatibility with the CMOS processing, TMAH was used as Si anisotropic etchants. The variations of Si etch rate on the etching temperature, TMAH concentration, and etching time were obtained. With increasing the etching temperature and decreasing TMAH concentrations, the Si etch rate is increased while a significant non-uniformity exists on the etched surface because of formation of hillocks on the <100> surface. With the addition of AP to TMAH solution, the Si etch rate is increased and an improvement in flatness on the etching front is observed. The Si etch rate is also maximized with increasing the number of addition of AP to TMAH solution per one hour. The Si square diaphragms of 20$\mu\textrm{m}$ thickness and 100-400 $\mu\textrm{m}$ one-side length were fabricated successfully by adding AP of (5/6)g to 800 ml TMAH solution every 10 minutes.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.3
• /
• pp.9-14
• /
• 2004

In this study, Si anisotropic etching characteristics of tetramethylammonium hydroxide (TMAH)/ ammonium persulfate(AP)/isopropyl alcohol(IPA) solutions were investigated to realize the optimum structure of a diaphragm for the piezoresistive pressure sensor application. Due to its low toxicity and its high compatibility with the CMOS processing, TMAH was used as Si anisotropic etchants. The variations of Si etch rate on the etching temperature, TMAH concentration, and etching time were obtained. With increasing the etching temperature and decreasing TMAH concentrations, the Si etch rate is increased while a significant non-unifonnity exists on the etched surface because of formation of hillocks on the (100) surface. The addition of IPA to TMAH solution leads to smoother etched surfaces but, makes the Si etch rate lower. However, with the addition of AP to TMAH solution, the Si etch rate is increased and an improvement in flatness on the etching front is observed. The Si etch rate is also maximized with increasing the number of addition of AP to TMAH solution per one hour. The Si square membranes of 20${\mu}{\textrm}{m}$ thickness and l00-400${\mu}{\textrm}{m}$ one-side length were fabricated successfully by applying optimum Si etching conditions of TMAH/AP solutions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.416-417
• /
• 2005

In this study, we optimized the process of Si anisotropy etching by combing tetramethyl ammonium hydroxide (TMAH) etching process with ultrasonic wave technology. New ultrasonic TMAH etching apparatus was developed and it was used for fabricating a $20{\mu}m$ thick diaphragm for Si piezoresistive pressure sensors. Based on comparison study on etch rate and surface flatness, it was observed that the Si anisotropy etching methode with new ultrasonic TMAH etching apparatus (at 40 kHz/ 500 watt) was superior to conventional etching methods with TMAH or TMAH+ammonium persulfate(AP) solutions.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2003.05a
• /
• pp.23-28
• /
• 2003

본 논문에서는 MEMS 공정기술을 이용하는 압저항(piezoresistive) 압력센서용 다이아프램의 최적구조 제작을 위한 TMAH(Tetramethyl Ammonium Hydroxide)의 식각특성을 연구하였다. KOH, EDP 등 기존의 공정 수행에 있어서 부딪치게 되는 환경적 요인을 개선하고, 생산성 향상을 위해 독성이 없고 CMOS 집적회로 공정과 호환성이 높은 TMAH를 사용하여, 식각온도와 TMAH 농도 및 식각시간에 따른 에칭률 변화를 측정하였다. 식각온도가 증가 함에 따라, 그리고 TMAH 농도가 감소함에 따라, Si 에칭률은 증가하였으나 hillock 발생률이 증가하여 식각표면의 평탄화 정도가 나빠졌다. 이러한 단점을 AP(Ammonium Persulfate) 첨가제를 이용하여 해결하였다. l5wt% 농도의 TMAH 800ml 용액을 가지고 매 10분당 같은 양의 AP를 1시간당 5g이 되도록 첨가하여, 한변의 길이가 100~400 $\mu\textrm{m}$인 정사각형 모양을 가진 우수한 이방성 다이아프램을 성공적으로 제작하였다.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.1033-1036
• /
• 2003

In this paper, Si anisotropic etching characteristics of tetramethylammonium hydroxide (TMAH)/ ammonium persulfate (AP) solutions were investigated to realize the optimum structure of a diaphragm for the piezoresistive pressure sensor application. Due to its low toxicity and its high compatibility with the CMOS processing, TMAH was used as Si anisotropic etchants. The variations of Si etch rate on the etching temperature, TMAH concentration, and etching time were obtained. With increasing the etching temperature and decreasing TMAH concentrations, the Si etch rate is increased while a significant non-uniformity exists on the etched surface because of formation of hillocks on the <100> surface. With the addition of AP to TMAH solution, the Si etch rate is increased and an improvement in flatness on the etching front is observed. The Si etch rate is also maximized with increasing the number of addition of AP to TMAH solution per one hour. The Si square diaphragms of 20${\mu}{\textrm}{m}$ thickness and 100~400${\mu}{\textrm}{m}$ one-side length were fabricated successfully by applying optimum Si etching conditions of TMAH/AP solutions.

• Polymer(Korea)
• /
• v.34 no.1
• /
• pp.38-44
• /
• 2010

Core-shell particles of inorganic/organic pair were synthesized from $CaCO_3$ absorbed sodium dodecyl benzene sulfonate(SDBS) surfactant. Shell components were synthesized by sequential emulsion polymerization. Various monomers were used as shell components such as methyl methacrylate(MMA), ethyl acrylate(EA), butyl acrylate(BA), and styrene(St). Ammonium persulfate(APS) was used as an initiator and 2-ethylhexyl acylate(2-EHA) was used as a functional monomer, In the $CaCO_3$/organic core-shell particle polymerization, $CaCO_3$ absorbed surfactant SDBS of 0.5 wt% was prepared first and then core $CaCO_3$ was encapsulated by emulsion polymerization. 0.1 wt% of APS was added sequentially to minimize the formation of new monomer particle during shell polymerization. The structure of inorganic/organic core-shell particles were characterized by measuring the decomposition degree of $CaCO_3$ using HCl solution, thermogravimetric analyzer, scanning electron microscope, and transmission electron microscope.