• Journal of Drive and Control
• /
• v.16 no.3
• /
• pp.42-50
• /
• 2019

3D printing AM processes have advantages in complex shapes, customized fabrication and prototype development stage. However, due to various parameters based on both the machine and the material, the AM process can produce finished output after several trials and errors in the initial stage. As such, minimizing or optimizing negative factors for various parameters of the 3D printing AM process could be a solution to reduce the trial-and-error failures in the early stages of such an AM process. In addition, this can be largely solved through software simulation in the preprocessing process of 3D printing AM process. Therefore, the objective of this study was to investigate a simulation technology for the AM software, especially Ansys Inc. The metal 3D printing AM process, the AM process simulation software, and the AM process simulation processor were examined. Through this study, it will be helpful to understand 3D printing AM process and AM process simulation processor.

• Journal of Drive and Control
• /
• v.16 no.3
• /
• pp.51-58
• /
• 2019

The objective of this study was to investigate a simulation technology for the AM field based on ANSYS Inc.. The introduction of metal 3D printing AM process, and the examining of the present status of AM process simulation software, and the AM process simulation processor were done in the previous study (part 1). This present study (part 2) examined the use of the AM process simulation processor, presented in Part 1, through direct execution of Topology Optimization, Ansys Workbench, Additive Print and Additive Science. Topology Optimization can optimize additive geometry to reduce mass while maintaining strength for AM products. This can reduce the amount of material required for additive and significantly reduce additive build time. Ansys Workbench and Additive Print simulate the build process in the AM process and optimize various process variables (printing parameters and supporter composition), which will enable the AM to predict the problems that may occur during the build process, and can also be used to predict and correct deformations in geometry. Additive Science can simulate the material to find the material characteristic before the AM process simulation or build-up. This can be done by combining specimen preparation, measurement, and simulation for material measurements to find the exact material characteristics. This study will enable the understanding of the general process of AM simulation more easily. Furthermore, it will be of great help to a reader who wants to experience and appreciate AM simulation for the first time.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.53 no.3
• /
• pp.188-196
• /
• 2004

Amplifier linearity plays a major role in the quality of mordern communication systems. The Power amplifier should be operated near saturation region to achieve high efficiency But at this region amplitude and phase distortions of the amplifier remarkably increase with the input power increase and cause a significant adjacent channel interference. In this paper, an independently controllable AM/AM and AM/PM predistortion linearizers consisted of two bias feed resistance linearizers is proposed. This linearizer allows independent adjustment of the AM/AM and AM/PM curves by using two adjustable voltages to compensate tile power amplifier non-linearities. The predistortion linearizer can improve the ACPR by 5.3dB with cdma2000 multi carrier signals. And by applying this linearizer to two-tone(880MHz) power amplifier, third order IMD products are improved up to 8(dB).

• Journal of Acupuncture Research
• /
• v.23 no.5
• /
• pp.31-37
• /
• 2006

Objectives & Methods : We investigated the cases for which spleen tonifying Sa-Am acupuncture was applied in ${\ulcorner}$Sa-Am-chim-gu-jeong-jeon(舍巖鍼灸正傳)${\lrcorner}$ and classified them according to the concepts of cold-heat & deficiency-excess for a better understanding of the application of spleen tonifying Sa-Am acupuncture. Results : 1. Tonification of Spleen Sa-Am acupuncture can be used to treat heat syndromes such as deficient fire caused by collapse of the spleen qi, stagnation of evil qi or spleen yin deficiency, by way of tonifying spleen qi, activating the flow of qi and blood or harmonizing spleen yin and yang. 2. Tonification of Spleen Sa-Am acupuncture can be used to treat cold syndromes such as weakness of spleen yang by way of promoting fire to generate earth, strengthening spleen yang and raising the clear yang. 3. Tonification of Spleen Sa-Am acupuncture can be used to treat deficiency syndromes such as malnutrition or poor appetite caused by spleen deficiency by way of tonifying spleen qi. 4. Tonification of Spleen Sa-Am acupuncture can be used to treat excess syndromes such as stagnation of qi and blood, abdominal mass or toxication by way of tonifying spleen qi and promoting the flow of qi and blood.

• Journal of Powder Materials
• /
• v.24 no.6
• /
• pp.494-507
• /
• 2017

A three-dimensional physical part can be fabricated from a three-dimensional digital model in a layer-wise manner via additive manufacturing (AM) technology, which is different from the conventional subtractive manufacturing technology. Numerous studies have been conducted to take advantage of the AM opportunities to penetrate bespoke custom product markets, functional engineering part markets, volatile low-volume markets, and spare part markets. Nevertheless, materials issues, machines issues, product issues, and qualification/certification issues still prevent the AM technology from being extensively adopted in industries. The present study briefly reviews the standard classification, technological structures, industrial applications, technological advances, and qualification/certification activities of the AM technology. The economics, productivity, quality, and reliability of the AM technology should be further improved to pass through the technology adoption lifecycle of innovation technology. The AM technology is continuously evolving through the introduction of PM materials, hybridization of AM and conventional manufacturing technologies, adoption of process diagnostics and control systems, and enhanced standardization of the whole lifecycle qualification and certification methodology.

• Nuclear Engineering and Technology
• /
• v.18 no.3
• /
• pp.194-199
• /
• 1986

The behavior of micro amount of Am in aqueous solution were investigated with centrifugation method as a function of pH. In the studies described here, equilibration times were extended to 2-3 weeks to know the aging effect in radiocolloid formation. Also, the effect of the addition of foreign materials, e. g. silica gel and Fe$^{3+}$ were examined as well as the effect of presence of concentrated electrolyte. In the results, Am appeared to be rapidly adsorbed on to impurity particles for pH < 6 and probably on the container walls by an ionic sorption process. The addition of foreign material increased the fraction of Am while the addition of concentrated electrolyte hindered the process. For pH > 7 Am behaved quite differently than for pH < 6. There appeared to be rapid sorption of some Am from solution probably on the container walls followed by partial desorption that occurred over a period of 1-2 days.s.

• Journal of Pharmaceutical Investigation
• /
• v.16 no.3
• /
• pp.110-117
• /
• 1986

Plasma disappearance of amaranth (AM), a model compound of organic anionic drugs, was retarded by intravenous infusion of taurodeoxycholate (TDC), a representative bile acid, in the rat. Biliary excretion accounted for 30-60% of the systemic excretion of AM. AM seemed to be metabolised in the hepatocyte to form a compound that is excreted more rapidly into the bile than AM itself, considering apparent biliary clearance, $CL_{bil}$, is much larger than systemic clearance, $CL_s$. Decrease in $CL_{bil}$ by TDC infusion might be due to elevated plasma level rather than decreased biliary excretion of AM. Decreased distribution or urinary excretion of AM by TDC was supposed to be one of the probable reasons of elevated plasma level. Competitive inhibition between AM and TDC on tissue distribution and urinary excretion might explain the mechanism. The effect of TDC on the $CL_{bil}$ of methylene blue, a cationic dye, was quite different from that of AM, as reported previously by us. More intensive study would be necessary to elucidate the difference of biliary excretion between organic anions and cations.

• Korean Journal of Materials Research
• /
• v.22 no.10
• /
• pp.499-503
• /
• 2012

The present study is intended to comparatively investigate the changes in microstructure and tensile properties at room and elevated temperatures in commercial AM50(Mg-5%Al-0.3%Mn) and 0.3 wt%CaO added ECO-AM50 alloys produced by permanent mould casting. The typical microstructure of AM50 alloy was distinctively characterized using two intermetallic compounds, ${\beta}(Mg_{17}Al_{12})$ and $Al_8Mn_5$, along with ${\alpha}$-(Mg) matrix in an as-cast state. The addition of a small amount of CaO played a role in reducing dendrite cell size and quantity of the ${\beta}$ phase in the AM50 alloy. It is interesting to note that the added CaO introduced a small amount of $Al_2Ca$ adjacent to the ${\beta}$ compounds, and that inhomogeneous enrichment of elemental Ca was observed within the ${\beta}$ phase. The ECO-AM50 alloy showed higher hardness and better YS and UTS at room temperature than did the AM50 alloy, which characteristics can be mainly ascribed to the finer-grained microstructure that originated from the CaO addition. At $175^{\circ}C$, higher levels of YS and UTS and higher elongation were obtained for the ECO-AM50 alloy, demonstrating that even 0.3 wt%CaO addition can be beneficial in promoting the heat resistance of the AM50 alloy. The combinational contributions of enhanced thermal stability of the Ca-containing ${\beta}$ phase and the introduction of a stable $Al_2Ca$ phase with high melting point are thought to be responsible for the improvement of the high temperature tensile properties in the ECO-AM50 alloy.

• Korean Journal of Microbiology
• /
• v.28 no.4
• /
• pp.290-296
• /
• 1990

Putrescine, spermidine, and spermine were found to persent in Methylobacterium extorquens AM1 growing on methanol, succinate, glucose, or nutrient broth as an energy source. Spermidine was found to be a major polyamine in cells growing on methanol or succinate, while putrescine to be the one in nutrient broth-grown cells. The overall content of polyamines in cells growing on glucose was less than that in cells growing on other substrates. Spermine was the most abundant polyamine in glucose-grown cells. Accumulation of polyamines in M. extorquens AM1 was maximal at the mid-exponential or early stationary phase during growth on each substrate. The effect of polyamines added into the medium on the polyamine composition in M. extorquens AM1 was variable. Each polyamine added into the nutrient broth medium was found to increase the amount of the respective polyamine in the cell. Exogeneously added polyamines had no effect on the growth of M. extorquens AM1.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.49 no.7
• /
• pp.399-406
• /
• 2000

We propose an nonlinear demodulation algorithm for undersampled multicomponent AM(Amplitude Modulation), FM(Frequency Modulation) and AM-FM signals. First, we derive respectively undersampling frequency of the AM, FM and AM-FM using undersampling scheme, and separate respectively monocomponent signals from multicomponent signals using periodic algebraic separation algorithm. In this case augmented separation matrix is very regular and sparse, it has a special structure. The proposed demodulation algorithm detects respectively message signals of the IA(Instantaneous Amplitude) and IF(Instantaneous Frequency) from descrete monocomponent AM, FM and AM-FM signals with an undersampling frequency to be controllable. Verifying the RMS(Root Mean Squares) errors of the detected signals, we show that the performance is excellent.