• Journal of the Korean Institute of Gas
• /
• v.9 no.4 s.29
• /
• pp.26-29
• /
• 2005

In this paper, the solvent sensing properties of the metallophthalocyanine macrocyclic compounds(ZnPc) have been deposited as thin films by the spin-coated method and evaporated methods onto alumina substrates and quartz substrates. And then the spin-coated materials of Zinc phthalocyanine solutions blended with $N,N'-diphenyl-N,N'-bis(1-naphthyl)-1,\;1-biphenyl-4,4'-diamine\;and/or\; Poly[2-methoxy-5-(2'-ethylhexyloxy)-1,4-phenylene-vinylene]$ solutions. The influences of the blended metallophthalocyanine macrocyclic compounds on the resistance have been measured and analysed in five different vapour organic compounds.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.3
• /
• pp.129-134
• /
• 2013

Sapphire wafers are used as an important substrate for the production of blue LED (light emitting diode) and the LED's performance largely depends on the quality of the sapphire single crystals. There are several crystal growth methods for sapphire crystals and Kyropoulos method is an efficient way to grow large diameter and high-quality sapphire single crystals with low dislocation density. During Kyropoulos growth, the convection of molten melt is largely influenced by the hot zone geometry such as crucible shape, heater and refractory arrangements. In this study, CFD (computational fluid dynamics) simulations were performed according to the bottom/side ratios (per unit of the crucible surface area) of heaters. And, based on the results of analysis, the molten alumina flows and remelting phenomena were analyzed.

• Korean Chemical Engineering Research
• /
• v.52 no.2
• /
• pp.205-208
• /
• 2014

Here, we reported mass-produced organic nanowires with uniform sizes based on poly(9,9-dioctylflurorene) (PFO), poly(9,9-dioctylfluorene-co-benzothiadiazole) (F8BT), (regioregular poly(3-hexylthiophene) (P3HT) which are well known as organic semiconductors for opto/electronics applications, using a melt-assisted wetting method with anodic alumina membrane. The conjugated polymer nanowires showed uniformed diameters (D=250~300 nm) and lengths ($L={\sim}30{\mu}m$) with defect free smooth surface regardless of a kinds of semiconductors. In addition, the nanowires were uniformly deposited onto glass substrates by spray-coating method. Under the UV light irradiation, PFO and F8BT nanowires showed blue and yellow emissions, respectively.

• Transactions of the Korean hydrogen and new energy society
• /
• v.26 no.4
• /
• pp.339-346
• /
• 2015

The synthesis of Fischer-Tropsch (FT) oil is the catalytic hydrogenation of CO to give a range of products, which can be used for the production of high-quality diesel fuel, gasoline and linear chemicals. This studied catalyst was prepared Cobalt-supported alumina and silica by the incipient wet impregnation of the nitrates of cobalt, promoter and organic solvent with supports. Cobalt catalysts were calcined at $350^{\circ}C$ before being loaded into the FT reactors. After the reduction of catalyst has been carried out under $450^{\circ}C$ for 24h, FT reaction of the catalyst has been carried out at GHSV of 4,000/hr under $200^{\circ}C$ and 20atm. From these experimental results, we have obtained the results as following; In case of $SiO_2$ catalysts, the activity of 12wt% $Cobalt-SiO_2$ synthesized by organic solvent was about 2 or 3 times higher than the activity of 12wt% $Cobalt-SiO_2$ catalyst synthesized without organic solvent. In particular, the activity of the $Cobalt-SiO_2$ catalyst prepared in the presence of an organic solvent P was two to three times higher than that of the $Cobalt-SiO_2$ catalyst prepared without the organic solvent. Effect of Cr and Cu metal as a promoter was found little. 200 h long-term activity test was performed with a $Co/SiO_2$ catalyst prepared in the presence of an organic solvent of Glyoxal solution.

• Transactions of the Korean hydrogen and new energy society
• /
• v.25 no.2
• /
• pp.105-113
• /
• 2014

Performance tests on $Ni/Ce-ZrO_2/Al_2O_3$ catalysts with additives (MgO, $La_2O_3$) were investigated in the combined reforming processes (SCR, ATR, TRM) in order to produce hydrogen and carbon monoxide (it is called "syngas".). The catalyst characterization was conducted using the BET surface analyzer, X-ray diffraction (XRD), SEM, TPR and TGA. The combined reforming process was developed to adjust the syngas ratio depending on the synthetic fuel (methanol, DME and GTL) manufacturing processes. Ni-based catalysts supported on alumina has been generally recommended as a combined reforming reaction catalyst. It was found that both free NiO and complexed NiO species were responsible for the catalytic activity in the combined reforming of methane conversion, and the $Ce-ZrO_2$ binary support employed had improved the oxygen storage capacity and thermal stability. The additives, MgO and $La_2O_3$, also seemed to play an important role to prevent the formation of the carbon deposition over the catalysts. The experimental results were compared with the equilibrium data using a commercial simulation tool (PRO/II).

• Progress in Medical Physics
• /
• v.27 no.4
• /
• pp.272-276
• /
• 2016

To investigate the optimum x-ray tube design for the dental radiology, factors affecting x-ray beam characteristics such as tungsten target thickness and anode angle were evaluated. Another goal of the study was to addresses the anode heel effect and off-axis spectra for different target angles. MCNPX has been utilized to simulate the diagnostic x-ray tube with the aim of predicting optimum target angle and angular distribution of x-ray intensity around the x-ray target. For simulation of x-ray spectra, MCNPX was run in photon and electron using default values for PHYS:P and PHYS:E cards to enable full electron and photon transport. The x-ray tube consists of an evacuated 1 mm alumina envelope containing a tungsten anode embedded in a copper part. The envelope is encased in lead shield with an opening window. MCNPX simulations were run for x-ray tube potentials of 70 kV. A monoenergetic electron source at the distance of 2 cm from the anode surface was considered. The electron beam diameter was 0.3 mm striking on the focal spot. In this work, the optimum thickness of tungsten target was $3{\mu}m$ for the 70 kV electron potential. To determine the angle with the highest photon intensity per initial electron striking on the target, the x-ray intensity per initial electron was calculated for different tungsten target angles. The optimum anode angle based only on x-ray beam flatness was 35 degree. It should be mentioned that there is a considerable trade-off between anode angle which determines the focal spot size and geometric penumbra. The optimized thickness of a target material was calculated to maximize the x-ray intensity produced from a tungsten target materials for a 70 keV electron energy. Our results also showed that the anode angle has an influencing effect on heel effect and beam intensity across the beam.

• Journal of the Korean Applied Science and Technology
• /
• v.26 no.3
• /
• pp.279-287
• /
• 2009

Fisher-Tropsch synthesis for the production of hydrocarbon from syngas was investigated on 20% cobalt-based catalysts (20% Co/HSA, 20% Co/Si-MMS), which were prepared by home-made supports with high surface areas such as high surface alumina (HSA) and silica mesopores molecular sieve (Si-MMS). In the gas phase reaction by syngas only, 20% Co/Si-MMS catalyst was shown in higher CO conversion and lower carbon dioxide formation than 20% Co/HSA, whereas the olefin selectivity was higher in 20% Co/HSA than in 20% Co/Si-MMS. In the effect of n-hexane added in syngas, the selectivities of $C_{5+}$ and olefin were increased by comparing the supercritical phase reaction with the gas phase reaction in addition to reduce unexpected methane and carbon dioxide.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.382-385
• /
• 2003

Chemical mechanical polishing(CMP) is an essential process in the production of copper-based chips. On this work, the stability of Hydrogen Peroxide($H_2O_2$) as oxidizer of Cu CMP slurry has been investigated. $H_2O_2$ is known as the most common oxidizer in Cu CMP slurry. Copper slowly dissolves in $H_2O_2$ solutions and the interaction of $H_2O_2$ with copper surface had been studied in the literature. Because hydrogen peroxide is a weak acid in aqueous solutions, a passivation-type slurry chemistry could be achieved only with pH buffered solution.[1] Moreover, $H_2O_2$ is so unstable that its stabilization is needed using as oxidizer. As adding KOH as pH buffering agent, stability of $H_2O_2$ decreased. However, stability went up with putting in small amount of BTA as film forming agent. There was no difference of $H_2O_2$ stability between KOH and TMAH at same pH. On the other hand, $H_2O_2$ dispersion of TMAH is lower than that of KOH. Furthermore, adding $H_2O_2$ in slurry in advance of bead milling lead to better stability than adding after bead milling. Generally, various solutions of phosphoric acids result in a higher stability. Using Alumina C as abrasive was good at stabilizing for $H_2O_2$; moreover, better stability was gotten by adding $H_3PO_4$.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.3
• /
• pp.297-304
• /
• 2016

A numerical simulation has been performed for the penetration of a long-rod penetrator into a metal block (ceramic-tile-inserted 4340-steel plate). The impact velocity is 1.5km/s at a normal incidence angle. The first two validations are conducted for a semi-infinite block measuring the depth of penetration (DOP). The material model of ceramic is the JH-2 (Johnson-Holmquist) model. The predicted DOP values are in close agreement with the experimental data. Then, the primary simulation is performed by varying the position of the confined ceramic tile for three types of thickness of ceramic tile. The residual velocity, residual mass and residual kinetic energy of the long-rod are obtained from the simulation. Based on these predicted values, the trend of the ballistic performance of the protective structure is estimated. In addition, the mass efficiency is calculated in order to determine the performance of the ceramic-tile-inserted metal block. Finally, the optimum protective structure is identified.

• Journal of the Korean Ceramic Society
• /
• v.38 no.10
• /
• pp.948-952
• /
• 2001

PZT thick films were fabricated on alumina substrates by a screen printing method. They were sintered at $750^{\circ}C{\sim}1050^{\circ}C$ for 1 h under air or Pb atmosphere. Pyrochlore was observed as a second phase in PZT thick films sintered in air at temperatures of $950^{\circ}C$ and higher. PZT thick films sintered under Pb atmosphere showed denser microstructure, higher dielectric constant, and better-developed P-E hysteresis curve than the films sintered in air. PZT thick films sintered at $900^{\circ}C$ under Pb atmosphere showed the typical ferroelectric hysteresis with remanent polarization of $29.8{\mu}C/cm^2$ and coercive field of 48.4 kV/cm.