• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.204-204
• /
• 2010

A development of device with reduced size and improved sensitivity is highly impotant Pb(Zr,Ti)$O_3$ thin films are widely used both to make actuator and sensor due to their high sensitivity and low cost. In this study, the feasibility of a piezoelectric presssure sensors based on hybrid low-temperaute co-fired ceramic (LTCC) technology were presented. The LTCC diaphragms with thickness of $400\;{\mu}m$ were fabricated by laminating 4 green tapes which consist of alumina and glass particle in an organic binder. PZT thin films were successfully prepared on between top and bottom Au electrode with LTCC substrates using RF magnetron sputtering. In addition, The frequency response characteristics of the sensor under varing pressure has been analysed. by Network Analyser (HP-8722D). A frequency shift range has been obseved from 1.7GHz to 1.8GHz with a good linearity for applied pressure from 0 psi up to 25 psi.

• 대한기계학회논문집A
• /
• 제20권10호
• /
• pp.3105-3112
• /
• 1996

Asymmetric creep behaviors of ceramics under high temperature were investigated. Based on the Norton's power-low creep equation, multidirectional creep equations were proposed for general geometric loading conditions. The proposed equations were implemented into finite element program (ABAQUS) to simulate creep behaviors of ceramics in complicated loading conditions. The calculated results were compared with experimental data for uniaxial compression of Si-SiC C-ring and flexure of Si-SiC and $Al_2O_3$ in the literature. The finite element results agreed well with experimental data when the principal stresses are smaller than the threshold stress for creep damage. A good agreement was also obtained for damage zone in Si-SiC bending creep specimen compared with experimental data.

• Advances in concrete construction
• /
• 제9권2호
• /
• pp.139-147
• /
• 2020

This paper reports the effect of Rice Husk Ash (RHA) in geopolymer concrete on strength, durability and microstructural properties under ambient curing at a room temperature of 25℃ and 65±5% relative humidity. Rice husk was incinerated at 800℃ in a hot air oven. and ground in a ball mill to achieve the required fineness. RHA was partially added in 10, 15, 20, 25, 30 and 35 percentages to fly ash with 10% of GGBS to produce geopolymer concrete. Test results exhibit that the substitution of RHA in geopolymer concrete resulted in reduced strength properties during initial curing. In the initial stage, workability of GPC mixes was affected by RHA particles due to the presence of dormant particles in it. It is evident from the microstructural study that the presence of RHA particles densifies the matrix reducing porosity in concrete. This is due to the presence of RHA in geopolymer concrete, which affects the ratio of silica and alumina, resulting in polycondensation reactions products. This study suggests that incorporation of rice husk ash in geopolymer concrete is the solution for effective utilization of waste materials and prevention of environmental pollution due to the dumping of industrial waste and to produce eco-friendly concrete.

• 한국세라믹학회지
• /
• 제22권5호
• /
• pp.76-84
• /
• 1985

Mechanical property enhancing mechanisms of $Al_2O_3-ZrO_2$ two phase ceramic composites were studied for several compositions of different $ZrO_2$/$Al_2O_3$ ratio. Microstructural analysis of $Al_2O_3-ZrO_3$(pure) composites indicated that pre-existing microcrack due to larger $ZrO_2$ particle at grain boundary extended along alumina grain boundaries within process zone. Microcracks also nucleated when very small $ZrO_2$ particles at the grain boundaries transformed to monoclinic phase at near of main crack tip. These types of microcracks could contribute to the toughening achieved by creating additional crack surface area during crack propagation. Microstructural analyses also showed that the average grain size and abnormal grain size of $Al_2O_3$ were decreased with increasing $ZrO_2$ vol% in $Al_2O_3$ matrix. As a result it could be concluded as follows In TEX>$Al_2O_3-ZrO_3$(pure) system 1. Microcrack nucleation (stress-induced microcracking) and extension was effective mechanism for absorpiton of fracture energy 2, More narrow distribution and smaller grain size of $Al_2O_3$ due to $ZrO_2$particles mainly contributed to main-tatin the strength and hardness.

• 대한전자공학회논문지
• /
• 제9권5호
• /
• pp.27-33
• /
• 1972

This paper describes the computer-aided design, fabrication and performance of high Q and high gain active filters suitable for microminiaturization in the frequency range of 10-800MHz, based on the negative resistance operation of a transistor. 48 as high as 1000 and a transducer gain as high as 35dB can readily be obtained with a single-transistor amplifier and with an inductance as small as a few nH at higher frequencies and 150 nH at lower frequencies in tile above frequency range. The gain of the proposed active filter can be stoabilized within $\pm$ 1.5 dB over the temperature range -1$0^{\circ}C$ to +5$0^{\circ}C$ and the temperature dependence of the center frequency is tapicalla 50ppm/$^{\circ}C$. An experimental FM receiver utilizing these fitters and operating at a carrier frequency of 92 MH3 was built. The whole circuit was fabricated on eight alumina substrates of by the thick-film hybrid IC technique and the coils are constructed, for miniaturization, in a spiral form of 3 or 4 turns of enamel copper wire with an overall diameter of about 5mm. The test results are also reported in this paper.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.71-73
• /
• 2005

Ferroelectric PZT heterolayered thick films were fabricated by the alkoxide-based sol-gel method. PZT(20/80) and PZT(80/20) paste were made and alternately screen-printed on the alumina substrates. The coating and drying procedure was repeated 4 times to form the heterolayered thick films. The thickness of the PZT heterolayered thick films was approximately 60 mm. All PZT thick films showed the typical XRD patterns of a perovskite polycrystalline structure. The relative dielectric constant and the dielectric loss of the PZT thick films sintered at $1050^{\circ}C$ were 1382 and 1.90%, respectively. The remanent polarization and coercive field of the PZT thick films sintered at $1050^{\circ}C$ were $14.15{\mu}C/cm^2$ and 19.13kV/cm, respectively.

• 전기학회논문지
• /
• 제63권11호
• /
• pp.1538-1544
• /
• 2014

In recent years, The electronic and energy industries demand low power consumption and high efficiency, so under their demands, the white goods industries which are represented for refrigerator and air conditioner system be implemented energy-saving power suppling structure with inverter control system. As inverter control system is different from step control type, when switching system is optimizing temperature control during short period, the inrush plus current can be flown in the circuit. In despite of these characteristics, there is no fuse which can be applied to this type until now. For this reason, we suggest the method of manufacturing protector in the high efficient inverter control system using the alumina-based ceramic radiated heat characteristics and metal films laminated plating. And through the evaluating electrical characteristics, we make a possible to utilize the method when designing overall fuses.

• Transactions on Electrical and Electronic Materials
• /
• 제6권1호
• /
• pp.29-32
• /
• 2005

Chemical mechanical polishing is an essential process in the production of copper-based chips. On this work, the stability of hydrogen peroxide ($H_{2}O_{2}$) as an oxidizer of copper CMP slurry has been investigated. $H_{2}O_{2}$ is known as the most common oxidizer in copper CMP slurry. But $H_{2}O_{2}$ is so unstable that its stabilization is needed using as an oxidizer. As adding KOH as a pH buffering agent, stability of $H_{2}O_{2}$ decreased. However, $H_{2}O_{2}$ stability in slurry went up with putting in small amount of BTA as a film forming agent. There was no difference of $H_{2}O_{2}$ stability between pH buffering agents KOH and TMAH at similar pH value. Addition of $H_{2}O_{2}$ in slurry in advance of bead milling led to better stability than adding after bead milling. Adding phosphoric acid resulted in the higher stability. Using alumina C as an abrasive was good at stabilizing for $H_{2}O_{2}$.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2003년도 총회 및 춘계학술발표회
• /
• pp.413-417
• /
• 2003

The last few decades have seen drastic growth in the use of brominated flame retardants(BFRs). There is the problems of polybrominated dibenzo-p-dioxins(PBDDS) and polybrominated dibenzofurans(PBDFs) generation as by-products in combustion process of BFRs. PBDDs/PBDFs are highlighted the new pollutants of environmental contamination, recently. In this study, the 10 kinds of PBDDs/PBDFs standards were used to perform the experiments of recoveries. The analysis of PBDDs/PBDFs in soil environmental samples. was carried out. In silica gel column cleanup, PBDDs/PBDFs eluted until 80mL of n-hexane, and the recovery was obtained 73∼105%. In multi-layer silica gel column cleanup, the recovery was obtained 56∼125% with various elution solvents. In alumina clean process, the standard mixture(PBDES, PBDDs/PBDFs) eluted the first fraction of 2% dichloromethane with n-hexane in the range of 0∼100mL, PBDEs compounds eluted in the second fraction of 50% dichloromethane with n-hexane. In activated carbon column cleanup, the PBBEs eluted to the first fraction(n-hexane) and second fraction(toluene), but PBDDs/PBDFs only eluted to the second fraction. The analytical methods of PBDDs/PBDFs for soil was established based on the experimental results of the environmental samples.

• 한국재료학회지
• /
• 제25권5호
• /
• pp.238-246
• /
• 2015

$H_2S$ is a flammable toxic gas that can be produced in plants, mines, and industries and is especially fatal to human body. In this study, CuO nanowire structure with high porosity was fabricated by deposition of copper on highly porous singlewall carbon nanotube (SWCNT) template followed by oxidation. The SWCNT template was formed on alumina substrates by the arc-discharge method. The oxidation temperatures for Cu nanowires were varied from 400 to $800^{\circ}C$. The morphology and sensing properties of the CuO nanowire sensor were characterized by FESEM, Raman spectroscopy, XPS, XRD, and currentvoltage examination. The $H_2S$ gas sensing properties were carried out at different operating temperatures using dry air as the carrier gas. The CuO nanowire structure oxidized at $800^{\circ}C$ showed the highest response at the lowest operating temperature of $150^{\circ}C$. The optimum operating temperature was shifted to higher temperature to $300^{\circ}C$ as the oxidation temperature was lowered. The results were discussed based on the mechanisms of the reaction with ionosorbed oxygen and the CuS formation reaction on the surface.