• 공업화학
• /
• 제2권3호
• /
• pp.289-299
• /
• 1991

후막 구리도체에 적합한 유리를 얻기 위하여 연붕규산계 및 무연 붕규산계 유리를 기반으로 하는 9종의 유리를 제조하고 후막 구리도체에의 적합성을 시험하였다. 그 결과 모든 유리들이 후막 구리도체의 쉬트 저항치, 납땜성 및 땜납 침식저항에는 양호하게 기여하는 것을 확인하였다. 그러나 후막과 알루미나 기판간의 노화후의 부착강도는 연붕규산계 유리로 만들어진 구리 도체막 만이 유용한 값을 가졌고, 그 외의 유리로 만들어진 구리 도체막의 노화후 부착강도는 사용하기에 부적합할 정도로 낮은 것이었다. 특히 $Cu_2O$ 가 첨가된 연붕규산계 유리가 후막 구리도체 제조에 가장 양호한 것으로 확인되었다.

• Membrane and Water Treatment
• /
• 제8권5호
• /
• pp.437-448
• /
• 2017

A high quality Na-X zeolite membrane was synthesized on a seeded ${\alpha}-alumina$ disc by the secondary growth method. Structural characterization was done by X-ray spectroscopy, FT-IR spectroscopy, SEM and AFM imaging. The performance evaluation of the membrane was firstly tested in separation of glucose/water solutions by pervaporation process. There was obtained a separation factor $182.7{\pm}8.8$, while the flux through the membrane was $3.6{\pm}0.3kg\;m^{-2}\;h^{-1}$. The zeolite membrane was then used for desalination of aqueous solutions consisting of $Na^+$, $Ca^{2+}$, $Cs^+$ and $Sr^{2+}$ because of the importance of these ions in water and wastewater treatments. The effects of some parameters such as temperature and solution concentration on the desalination process were studied for investigating of diffusion/adsorption mechanism in membrane separation. Finally, high water fluxes ranged from 2 up to $9kg\;m^{-2}\;h^{-1}$ were obtained and the rejection factors were resulted more than 95% for $Na^+$ and $Ca^{2+}$ and near to 99% for $Cs^+$ and $Sr^{2+}$. Based on the results, fluxes were significantly improved due to convenient passage of water molecules from large pores of NaX, while the fouling was declining dramatically. Based on the results, NaX zeolite can efficiently use for the removal of different cations from wastewaters.

• 대한기계학회논문집B
• /
• 제31권10호
• /
• pp.823-831
• /
• 2007

This paper presents the experimental and simulation study of a loop heat pipe (LHP) that can be applied to present electronics, space missions and thermal control systems. The present experimental study was carried out employing sintered alumina ceramic wick ($d=2.96\;{\mu}m$, ${\phi}=0.61$). High purity R-134a, R-22 and water were also used as alternative working fluids in addition to ammonia. The experimental study showed that the maximum heat transfer performance for the test LHP in the vertical top heating mode was over 100 Watts when ammonia was used as the working fluid. The simulation results have been compared with the experimental results to validate a simulation model based on the thermal resistance network that was developed to evaluate the performance of LHPs, focusing on their prospective applications in electronics. The simulation model is based on the loop overall energy, mass, and momentum balance. The simulation program can predict the effects of various parameters which affect the performance of LHP within 5% compared with the experimental results.

• 한국공작기계학회논문집
• /
• 제13권2호
• /
• pp.33-39
• /
• 2004

Sandblasting has recently been developed into a powder blasting technique for brittle materials. In this study, the machinability of $Si_3N_4$-hBN based machinable ceramics are evaluated for micro - pattern making processes using powder blasting. Material properties of the developed machinable ceramics according to the variation of h-BN contents give a good machinability to the ceramics. The effect of scanning times, the size of patterns and variation of BN contents on the erosion depth of samples without mask and samples with different mask patterns in powder blasting of $Si_3N_4$-hBN ceramics are investigated. The Parameters are the impact angle of $90^{\circ}$, the scanning times of nozzle up to 40, and the stand-off distances of 100mm The widths of masked pattern are 0.1mm 0.5mm and 1mm. The powder used is Alumina particles, WA#600. and the blasting pressure of powder is 0.2MPa. Through required experiments, the results are investigated and analyzed. As the results, the machinability of the developed ceramics increases as the BN contents in the ceramics.

• 한국재료학회지
• /
• 제24권8호
• /
• pp.413-416
• /
• 2014

The effects of an addition of CNT on the sensing properties of nano ZnO:CNT-based gas sensors were studied for $H_2S$ gas. The nano ZnO sensing materials were grown by a hydrothermal reaction method. The nano ZnO:CNT was prepared by ball-milling method. The weight range of the CNT addition on the ZnO surface was from 0 to 10%. The nano ZnO:CNT gas sensors were fabricated by a screen-printing method on alumina substrates. The structural and morphological properties of the ZnO:CNT sensing materials were investigated by XRD, EDS, and SEM. The XRD patterns revealed that nano ZnO:CNT powders with a wurtzite structure were grown with (1 0 0), (0 0 2), and (1 0 1) dominant peaks. The size of the ZnO was about 210 nm, as confirmed by SEM images. The sensitivity of the nano ZnO:CNT-based sensors was measured for 5 ppm of $H_2S$ gas at room temperature by comparing the resistance in air with that in target gases.

• 한국전기전자재료학회논문지
• /
• 제13권7호
• /
• pp.568-574
• /
• 2000

We have been optimized tungsten(W) plug CMP(chemical mechanical polishing) characteristics using two different kinds of component of slurry and two different kinds of pad which have different hardness. The comparison of oxide film roughness on around W plug after polishing has been carried out. And W plug recess for consumable sets and dishing effect at dense area according to the rate of over-polishing has been investigated. Also the analysis of residue on surface after cleaning have been performed. As a experimental result we have concluded that the consumable set of slurry A and hard pad was good for W plug CMP process. After decreasing the rate of chemical reaction of silica slurry and adding two step buffering we could reduce the expanding of W plug void however we are still recognizing to need a more development for those kinds of CMP consumables.

• 소성∙가공
• /
• 제21권4호
• /
• pp.228-233
• /
• 2012

In this study, powder compaction of AZO (alumina doped zinc oxide) powder was performed with a MTS 810 test system using a cylindrical die having a diameter of 10mm. Pressure-density curves were measured based on the load cell and displacement of the punch. The AZO powder compacts with various densities were formed to investigate the mechanical properties such as fracture stress of the AZO powder as a function of the compact density. Two types of compression tests were conducted in order to estimate the fracture stress using different loading paths: a diameteral compression test and a uniaxial compression test. The pressure-density curves of the AZO powder were obtained and the fracture stress of the compacted powders with various densities was estimated. The results show that the compact pressure dramatically increases as the density increases. Based on the experimental results, calibration of the modified Drucker-Prager/Cap model of the AZO powder for use in FE simulations was developed.

• 대한의용생체공학회:의공학회지
• /
• 제43권4호
• /
• pp.219-229
• /
• 2022

In this study, we propose a miniaturized micro-ceramic heater device. After screen-printing a silver paste between pre-sintered two aluminum oxide plates to integrate a heating circuit, the device was fabricated through a low-temperature sintering process. In order to configure the optimal heating circuit integration condition, the output current evaluation and heating test were performed according to the number of screen prints of the silver paste at various voltages. A silver paste-based heating circuit printed with a line width of 200 ㎛ and a thickness of 60 ㎛ was successfully integrated on a pre-sintered alumina substrate through a low-temperature sintering process. In the case of the 5 times printed device, the thermal response showed a response rate of 18.19 ℃/sec. To demonstrate feasibility of the proposed device in the medical field, such as bio-tissue suturing and hemostasis, a voltage was applied to pig tissue in the device to test tissue change due to heat generated from the device. These results show the possibility that the proposed small ceramic heater could be used in the medical field based on its excellent temperature response.

• KSBB Journal
• /
• 제15권3호
• /
• pp.285-292
• /
• 2000

난초를 키우는 화분에 보습용으로 사용되는 다공성 화산석을 2-3 mm크기로 파쇄한 후 $600^{\circ}C$에서 1시간 태워서 가연성 물질 을 제거하고 IN의 염산용액으로$60-70^{\circ}C$에서 2시간 이물질을 녹여댄 후 세척할 경우 효모 고정화에 적당한 담체를 얻을 수 있었다 이 때 염산 용액 대신 NaOH 용액을 세척용액으로 사용 할 수 있으나 담체 구성성분의 용출이 있을 수 있으므로 용액 농도, 처리온도 및 시간에 주의하여야 한다 이렇게 제조된 담체 는 기공의 크기가 $15-80\mu\textrm{m}$이고 충전 밀도는 0.4-0.6 g/mL 였으며 $SiO_2$가 주성분이었고, $Al_2O_3$가 소량함유되어 있었으며, CaO, MgO가 미량 함유되어 있었다. 이 담제의 구조와 효모 고 정화 능력을 국내외 기업에서 제조한 실리카 및 알루미나 재질 의 담체의 경우와 비교한 결과 고상포말법으로 제조한 실리가 담체의 구조 및 고정화능력($5{\times108}$ cells/mL bed)과 비슷한 결 과를 보여 효모 고정화용 담체로 손색이 없었다.. Cordierite 담체 와 알루미나 담체는 고정화능이 실리카 담체의 50% 이하로 낮 았는데 이는 기공의 표면이 매끄럽지 못했기 때문으로 효모가 쉽게 흡착하기 위해서는 가능한 한 매끄러운 표면이 바람직하다 는 사실을 알 수 있었다.

• 한국주조공학회지
• /
• 제21권3호
• /
• pp.163-178
• /
• 2001

The squeeze infiltration process is potentially of considerable industrial importance. The performance enhancements resulting from incorporation of short alumina fiber into aluminum are well documented. These are particularly significant for certain automobile components. Aluminum matrix composite automotive parts, such as diesel engine pistons or engine blocks are produced using squeeze casting apparatus or pressure die-casting apparatus. But the solidification process gets complicated with manufacturing parameters and the factors for porosity formation have not fully understood yet. In this study the formation of porosity during squeeze infiltration has been studied experimentally to achieve an improved understanding of the squeeze infiltration process for manufacture of short-fiber-reinforced components, particularly the mechanism of porosity formation. Al-based MMCs produced under a range of conditions were examined metallographically and the porosity characterised;a kind of matrix, an initial temperature of melt, and a volume fraction of reinforcement. The densimetry and the microscopic image analysis were done to measure the amount of porosity. A correlation between manufacturing parameters and defects was investigated through these.