• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.233-233
• /
• 2008

A piezoelectric ultrasonic linear motor shaped with 'Butterfly' wings has been developed for thin electronics such as cellular phone and PDA. The butterfly piezoelectric transducer is simply composed of an elastic plate, which includes a tip for energy transfer and two protrusions to fix it, and two piezoelectric ceramics. Contact materials, such as a brass, and steel and alumina can make it possible to improve dynamic properties of the motors over a wide range of tribological conditions. The dynamic properties of the motor have been intensively measured and analyzed according to the applied voltage wave forms at the various frequencies. The results of numerical study and experimental investigation will be used for the future optimization of the actuator and the realization of the advanced ultrasonic motor.

• 한국해양공학회지
• /
• 제23권5호
• /
• pp.32-38
• /
• 2009

Silicon nitride samples with aligned whisker seeds were prepared with different amounts of yttria and alumina as the sintering additives. Their sintering behaviors and the microstructural developments between $1850^{\circ}C$ and $2050^{\circ}C$ were examined. The sample with larger amount of the sintering additives showed faster densification and grain growth. Even though addition of the aligned whisker seeds slightly retarded densification of silicon nitride, it improved the flexural strength and the fracture toughness. Both the flexural strength and the fracture toughness of silicon nitride with the aligned whisker seeds were increased as the amount of the sintering additives was increased.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.71-73
• /
• 2005

Ferroelectric PZT heterolayered thick films were fabricated by the alkoxide-based sol-gel method. PZT(20/80) and PZT(80/20) paste were made and alternately screen-printed on the alumina substrates. The coating and drying procedure was repeated 4 times to form the heterolayered thick films. The thickness of the PZT heterolayered thick films was approximately 60 mm. All PZT thick films showed the typical XRD patterns of a perovskite polycrystalline structure. The relative dielectric constant and the dielectric loss of the PZT thick films sintered at $1050^{\circ}C$ were 1382 and 1.90%, respectively. The remanent polarization and coercive field of the PZT thick films sintered at $1050^{\circ}C$ were $14.15{\mu}C/cm^2$ and 19.13kV/cm, respectively.

• 한국정밀공학회지
• /
• 제18권5호
• /
• pp.98-104
• /
• 2001

A dynamic fracture toughness test method with a chevron notched ceramic specimens is proposed. The notch angles of the chevron specimens were 90, 100$^{\circ}$and 110$^{\circ}$. Finite element analysis(FEA) were done to determine the geometrical properties of chevron-notch specimens according to notch angles. The static fracture toughness of the chevron notched alumina specimen was 3.8MP$\alpha$√m similar to that of the general fracture specimen with a precrack. Dynamic fracture toughness was 4.5 MP$\alpha$√m slightly higher than the static one. These research showed the possibility of the split Hopkinson pressure bar test method using the newly proposed chevron notched specimens to get the dynamic fracture toughness of extremely brittle materials such as ceramics.

• 한국레이저가공학회지
• /
• 제18권4호
• /
• pp.17-22
• /
• 2015

In this paper, ablation rate of $Al_2O_3$ ceramics by femtosecond laser fluence is derived with experimental method. The automatic three axis linear stage makes laser optics to move with high spatial resolution. With 10 times objective lens, minimal pattern width of $Al_2O_3$ is measured in the focal plane. Ablated surface area is shown as linear tendency increasing number of machining times with various laser power conditions. Machining times is most sensitive condition to control $Al_2O_3$ pattern width. Also, the linear increment of pattern width with laser power change is investigated. In high machining speed, the ablation volume rate is more linear with fluence because pulse overlap is minimized in this condition. Thermal effect to surrounding medium can be minimized and clean laser process without melting zone is possible in high machining speed. Ablation volume rate decelerates as increasing machining times and multiple machining times should be considered to achieve proper ablation width and depth.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 제5회 영호남 학술대회 논문집
• /
• pp.31-34
• /
• 2003

($Ba_{0.6-x}Sr_{0.4}Ca_x)TiO_3$ (BSCT) (x=0.10, 0.15, 0.20) powder, prepared by the sol-gel method, were mixed with organic vehicle and the BSCT thick films were fabricated by the screen-printing techniques on alumina substrates using the BSCT paste. The structural and the electrical properties were investigated for various composition ratio and sintering temperature. BSCT thick film thickness, obtained by four printings, was approximately 110 ~ 120 ${\mu}m$. The Curie temperature and dielectric constant at room temperature were decreased with increasing Ca content. The relative dielectric constant, dielectric loss and tunability of the BSCT(50/40/10) specimen, which was sintered at $1420^{\circ}C$ and measured at 1MHz, were about 910, 0.46% and 9.28% at 5kV/cm, respectively.

• The Korean Journal of Ceramics
• /
• 제3권3호
• /
• pp.199-207
• /
• 1997

$Al_2O_3$/SiC particulate composites were fabircated by pressureless sintering. The dispersed phase was SiC of which the content was varied from 1.0 to 10 vol%. Three SiC powders having different median diameters from 0.28 $\mu\textrm{m}$ to 1.9 $\mu\textrm{m}$ were used. The microstructure became finer and more uniform as the SiC content increased except the 10 vol% specimens, which were sintered at a higher temperature. Under the same sintering condition, densification as well as grain growth was retarded more severly when the SiC content was higher or the SiC particle size was smaller. The highest flexural strength obtained at 5.0 vol% SiC regardless of the SiC particle size seemed to be owing to the finer and more uniform microstructures of the specimens. Annealing of the specimens at $1300^{\circ}C$ improved the strength in general and this annealing effect was good for the specimens containing as low as 1.0 vol% of SiC. Fracture toughness did not change appreciably with the SiC content but, for the composites containing 10 vol% SiC, a significantly higher toughness was obtained with the specimen containing 1.9$\mu\textrm{m}$ SiC particles.

• 한국세라믹학회지
• /
• 제53권6호
• /
• pp.700-706
• /
• 2016

Etch rate, surface roughness and microstructure as plasma resistance were evaluated for six kinds of oxide glass with different compositions. Borosilicate glass (BS) was found to be etched at the highest etch rate and zinc aluminum phosphate glass (ZAP) showed a relatively lower etch rate than borosilicate. On the other hand, the etching rate of calcium aluminosilicate glass (CAS) was measured to be similar to that of sintered alumina while yttrium aluminosilicate glass (YAS) showed the lowest etch rate. Such different etch rates by mixture plasma as a function of glass compositions was dependent on whether or not fluoride compounds were formed on glass and sublimated in high vacuum. Especially, in view that $CaF_2$ and $YF_3$ with high sublimation points were formed on the surface of CAS and YAS glasses, both CAS and YAS glasses were considered to be a good candidate for protective coating materials on the damaged polycrystalline ceramics parts in semi-conductor and display processes.

• 한국전기전자재료학회논문지
• /
• 제16권4호
• /
• pp.304-310
• /
• 2003

(Ba$\sub$0.6-x/Sr$\sub$0.4/Ca$\sub$x/)TiO$_3$(BSCT) (x=0.10, 0.15, 0.20) powder, prepared by the sol-Bel method, were mixed with organic binder and then BSCT thick films were fabricated by the screen printing techniques on alumina substrates using the BSCT paste. The structural and the dielectric Properties were investigated for various composition ratio and sintering temperature. The second phase appeared in BSCT(40/40/20) thick film sintered at 1450$^{\circ}C$. BSCT thick film thickness, obtained by four printings, was approximately 110∼120$\mu\textrm{m}$. The Curie temperature and dielectric constant at room temperature were decreased with increasing Ca content. The relative dielectric constant, dielectric loss and tunability of the BSCT(50/40/10) specimen, which was sintered at 1420$^{\circ}C$ and measured at 1MHz, were about 910, 0.46% and 9.28% at 5㎸/cm, respectively.

• 한국기계가공학회지
• /
• 제12권6호
• /
• pp.3-9
• /
• 2013

Aluminum Oxide($Al_2O_3$) ceramics are excellent candidates for such applications due to their outstanding mechanical, thermal, and tribological properties. However, they are difficult to machine using conventional mechanical methods. Carbon fillers, such as carbon nanotubes(CNT) and graphene nanoplatelets(GNP)can be dispersed in a ceramic matrix to improve the mechanical and electrical properties. In this study, CNT and Graphene reinforced hybrid ceramic composites were fabricated using the spark plasma sintering method at a temperature of $1,500^{\circ}C$, pressure of 40 MPa, and soaking time of 10min. Besides this, the material properties such as microstructure, crystal structure, hardness, and electrical conductivity were analyzed using FE-SEM, XRD, Vickers, and the 4-point probe method. A micro machining test was carried out to compare the effects of the material properties and the machining performance for CNT and Graphene reinforced ceramic composites.