• 한국버섯학회지
• /
• 제18권4호
• /
• pp.387-392
• /
• 2020

국내 유통 중인 건조 목이 8건(국내산 3건, 중국산 5건)을 수집하여 잔류농약 321종, 중금속 7종, 방사능 3종의 유해물질 잔류성분을 조사하였다. 잔류농약 검사결과 국내산 3건에서는 검출되지 않았으나, 중국산 5건 중 4건에서 Chlorpyrifos, Isoprocarb, Mepiquat chloride, Carbendazim이 검출되었다. 농산물 농약 잔류허용기준에 의하면 목이는 Mepiquat chloride(0.5 mg/kg 이하)만 기준치가 설정되어 있다. 또한 중금속 검사결과는 모든 건조 목이에서 미량의 중금속이 검출되었으나, 기준치 이하로 낮게 나타났다. 다만 국내산 시료 1건에서 납 함량이 기준치(0.3 mg/kg)보다 높게 나타나 정확한 원인 규명을 위해서는 톱밥배지, 지하수, 보관·유통 과정에 대한 추가적인 조사가 필요할 것으로 보여진다. 방사능 조사결과에서는 모든 건조 목이에서 방사능 농도가 MDA값 이하로 불검출 수준으로 나타났다. 국내산과 중국산의 평균 방사능 농도는 요오드(131I)와 세슘(134Cs)은 비슷한 수준으로 나타났으며, 세슘(137Cs)은 국내산보다 중국산에서 다소 높게 나타났다. 방사성 세슘(137Cs)은 버섯류에 잘 농축되는 것으로 알려져 있는데 이번 조사에서는 국내 유통 중인 건조 목이는 방사능에 안전하게 나타났다.

• 한국터널지하공간학회 논문집
• /
• 제20권6호
• /
• pp.1125-1146
• /
• 2018

쉴드 TBM터널에 적용되는 세그먼트 라이닝은 주로 콘크리트로 제작되며, 시공 중 및 완공 후 작용 하중에 견딜 수 있는 충분한 강도가 요구된다. 한계상태설계법에 의한 세그먼트라이닝 설계는 주로 극한하중상태(ULS) 및 사용하중상태(SLS)에 대하여 검토하며, 상시하중과 임시하중에 대하여 발생 가능한 조합을 구성하여 적용한다. 또한 TBM에 의한 시공을 고려한 한계상태 설정과 구조해석이 필요하며, 특히 세그먼트라이닝은 현장에서 조립되어 원형구조물을 완성하는 방식이기 때문에, 콘크리트표면이 접촉하는 조인트가 필수적으로 존재하며 이 조인트를 통해 상당한 크기의 압축응력이 전달되므로 조인트에 대한 구조검토가 중요하다. 일반적으로 세그먼트 라이닝의 원주방향 조인트(circumferential joint)와 반경방향 조인트(radial joint)에서의 인장응력에 대하여 FEM모델이나 이론식으로 검토한다. 영국의 설계지침(PAS 8810, 2016)에 의하면, 버스팅을 일으키는 조인트에서의 압축응력은 원주방향 조인트(circumferential joint)에 잭 추력을 가하는 경우뿐만 아니라 반경방향 조인트(radial joint)에 축력이 전달되는 경우에도 발생하므로 버스팅 응력을 검토하여 세그먼트의 인장강도와 비교하여 필요할 경우 보강을 하여야 한다. 본 연구에서는 대표적인 한계상태설계코드인 EURO CODE와 AASHTO LRFD (2017)의 하중조건을 적용하여 조인트 응력을 비교 분석하였고, FEM해석을 통하여 버스팅(bursting)을 유발하는 조인트응력을 평가하고 발생경향을 이론식과 비교 분석하였다. 분석결과, 조인트 응력이 콘크리트의 허용 인장강도를 초과하는 경우가 발생하여 보강이 필요한 것으로 검토되었다. 따라서 조인트 버스팅 검토는 세그먼트라이닝 한계상태설계 시 설계항목으로 비중 있게 고려할 필요가 있다.

• 한국강구조학회 논문집
• /
• 제17권3호통권76호
• /
• pp.357-363
• /
• 2005

건축물이 고층이 될 수록 고강도 강재의 사용요구가 증대된다. 그러나 고강도 강재는 일반 강재와는 전혀 다른 기계적 특성을 갖고 있다. 고강도 강재를 건축구조물에 적용하기 위해서는 비탄성 영역에서의 거동이 일반 강재와 동등한가를 확인해야 한다. 본 연구에서는 SM570TMC 강재로 제작된 박스형 및 H형 단면을 갖는 기둥의 국부좌굴강도를 평가하기 위해서 중심압축실험을 세장비를 변수로 수행하였다. 단주압축 실험결과 판폭두께비의 제한치를 만족하는 기둥부재의 최대내력은 국부좌굴에 의해 결정되며, 판폭두께비를 만족시키지 못하는 경우에는 최대내력에 도달하기 전에 국부좌굴이 발생되었으나 급격한 내력저하는 발생되지 않았다. 장주압축 실험결과 SM570TMC 강재는 허용응력도 설계법과 한계상태 설계법에서 정하고 있는 설계기준을 만족하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1991년도 추계학술발표회 논문집 지반공학에서의 컴퓨터 활용 COMPUTER UTILIZATION IN GEOTECHNICAL ENGINEERING
• /
• pp.108-122
• /
• 1991

주어진 터널 斷面 및 地盤條件을 對象으로 1次元 有限要素 프로그램인 MrSoil을 利用하여 數値解析을 遂行하고 그 結果를 本稿에 收錄하였다. 解析 모델은 過去의 터널 計測 結果等에 根據하여 터널 掘進 影 이 充分히 적은 地域까지로 擴張 設定하여 境界條件에 의한 解析結果에의 影響을 最小化하도록 하였으며, 3次元的인 터널 擧動을 適切히 Simulation 하기 위하여 施工順序를 導入하여 段階別로 解析을 遂行하였다. 解析結果 터널 天井部는 最大 約 35mm의 沈下가 豫想되며, 地表面 沈下는 13mm 以內로서 地上 構造物의 構造的인 被害는 없을 것으로 判斷된다. 支保工인 Shotcrete와 Rockbolt의 最大應力 및 軸力도 各各 84 Kg/cm2 및 9론 以內로서 許容値 以內이고, 掘面 周邊의 塑性領域은 Rockbolt 길이 以內로 制限되고 있으므로 天井部에 Forepoling을 設置한다면, 터널 安全에는 影響을 미치지 않을 것으로 判斷되므로 本 터널은 合理的이며 適切히 設計된 것으로 評價된다.

• 콘크리트학회논문집
• /
• 제27권5호
• /
• pp.471-480
• /
• 2015

최근 국내의 건축구조는 공간활용을 극대화할 수 있도록 계획되고 있다. 공간활용의 장점을 실현하기 위하여 하이브리드 OCB (Optimized Composite Beam)를 개발하였다. 건축용 OCB는 부모멘트 구간에서는 노출강연선으로 보강된 H형강으로 구성되고 정모멘트 영역에서는 PSC 구조로 구성된다. 본 연구에서는 건축용 OCB의 휨성능을 조사하였다. 15 m 길이의 시험체를 제작하여 3점 휨실험을 실시하였다. 실험을 통해서 다음과 같은 결과를 얻었다. 1) 시험체의 재하실험에서 초기 균열은 설계사용 하중의 171%에서 발생되었다. 2)사용하중에서 처짐은 건축구조설계기준에 제시된 허용처짐량 이내로 만족하였다. 3)균열의 양상, 파괴모드 그리고 극한하중 등의 실험결과는 3D 수치해석결과와 비교검토되었다. 본 실험연구 결과로부터 건축용 OCB보의 구조적인 신뢰성이 입증되었다.

• 자원환경지질
• /
• 제37권1호
• /
• pp.49-59
• /
• 2004

The concectration and distribution of contaminants obtained from a contaminated land investigation or an environmental geochemistry survey constitutes the basis of a decision-making process on environmental policies or of scientific researches. As the quality of data determines the reliability of the result, the investigation plan should be adjusted according to the purpose of the investigation. In general, the effort to improve the data quality had been focused mainly on the QA/QC procedures in laboratories. The rapid progress of analytical instrument has also contributed toward improving the analytical precision to a sacrificable degree. Nevertheless, in many cases, it is not the analytical precision that needs improvement for the better precision of overall measurement process: it is rather during the sampling process in the field that is responsible for the poor precision. To assess the data quality on a measured value, ISO recommends to provide information on "measurement uncertainty" along with the measured value. The measurement uncertainty in an environmental measurement context can be explained as the statistical number that expresses the degree of the uncertainty stemming from the sampling and analytical procedures. There is a cost involved in order to improve the precision of sampling and analytical methods so as to decrease the degree of measurement uncertainty. The economical point of compromise in an investigation planning can be achieved when the allowable degree of uncertainty has been set before-hand. The investigation can then be planned accordingly not to exceed the uncertainty limit. Furthermore, if the measurement uncertainty estimated from the preliminary investigation can be separated into sampling and analytical uncertainties, it can be used as a criterion where the resources for the investigation should be allotted cost-effectively to reinforce the weakest link of the whole investigation process. This paper aims to present a method of estimating the level of measurement uncertainty of a measured contamination concentration at a site used as an example and to show how the estimated uncertainty can be applied to serve the particular purpose of an investigation.

• 신재생에너지
• /
• 제7권3호
• /
• pp.67-73
• /
• 2011

MGT fuelled by landfill gas was tested to asses feasibility of its exhaust gas application for $CO_2$ enrichment. The exhaust gas was analyzed during start-up and normal operation with different MGT load conditions. Due to the changes of air/fuel ratio and combustion mode, $O_2$, $CO_2$, CO and NOx concentration were varied within wide ranges during the MGT start-up. Especially, NOx emissioin level was increased up to 20.01 ppmv. Different tendencies of $O_2$, $CO_2$, CO and NOx concentrations were observed with MGT output changes. $O_2$ and CO concentrations were shown to be decreased and NOx and $CO_2$ concentrations were shown to have opposite trends. NOx emission level (0.8~1.88 ppmv) was very low compared to other types of combustion based power generation equipment. Unburned hydrocarbon emission level was substantially decreased with MGT load increase. Especially, $C_2H_4$ concentration was below the detection limit(0.2 ppmv) around the nominal load condition. The exhaust gas from landfill gas fuelled MGT system was shown to be feasible for $CO_2$ fertilization. Concentrations of major components were within or below the maximum allowable ranges.

• 한국도로학회논문집
• /
• 제20권3호
• /
• pp.65-73
• /
• 2018

PURPOSES : In this study, the propriety of expansion joint spacing of airport concrete pavement was examined by using weather and material characteristics. METHODS : A finite element model for simulating airport concrete pavement was developed and blowup occurrence due to temperature increase was analyzed. The critical temperature causing the expansion of concrete slab and blow up at the expansion joint was calculated according to the initial vertical displacement at the joint. The amount of expansion that can occur in the concrete slab for 20 years of design life was calculated by summing the expansion and contraction by temperature, alkali-silica reaction, and drying shrinkage. The effective expansion of pavement section between adjacent expansion joints was calculated by subtracting the effective width of expansion joint from the summation of the expansion of the pavement section. The temperature change causing the effective expansion of pavement section was also calculated. The effective expansion equivalent temperature change was compared to the critical temperature, which causes the blowup, according to expansion joint spacing to verify the propriety of expansion joint applied to the airport concrete pavement. RESULTS : When an initial vertical displacement of the expansion joint was 3mm or less, the blowup never occurred for 300m of joint spacing which is used in Korean airports currently. But, there was a risk of blow-up when an initial vertical displacement of the expansion joint was 5mm or more due to the weather or material characteristics. CONCLUSIONS : It was confirmed that the intial vertical displacement at the expansion joint could be managed below 3mm from the previous research results. Accordingly it was concluded that the 300m of current expansion joint spacing of Korean airports could be used without blowup by controling the alkali-silica reaction below its allowable limit.

• 한국정밀공학회지
• /
• 제25권2호
• /
• pp.148-155
• /
• 2008

The aim of the study is to interpret the distribution of occlusal force by 3-dimensional finite element analysis of ISP(Implant Supported Prosthesis) supported by minimum number of implant to restore the edentulous patients. For this study, the Astra Tech implant system is used. Geometric modeling for 6 and 4 fixture ISP group is performed with respect to the bone, implant and one piece superstructure, respectively. Implants are arbitrarily placed according to the anatomical limit of lower jaw and for the favorable distribution of occlusal force, which is applied at the end of cantilever extension of ISP with 30mm. Element type is tetrahedral for finite element model and the typical mechanical properties, Young's modulus and Poisson's ratio of each material, cortical, cancellous bone and implant material are utilized for the finite element analysis. From this study, we can see the distribution of equivalent stress equal to real situation and speculate the difference in the stress distribution in the whole model and at each implant fixture, From the analysis, the area of maximum stress is distributed on distal contact area between bone and fixture in the crestal bone. The maximum stress is 53MPa at the 0.2mm area from the bone-implant interface in the maximum side for 300N load condition for 4 fixture case, which is slightly less than the stress calculated from allowable strain. This stress has not been deduced to directly cause the loss of crestal bone around implant fixture, but the stress can be much reduced as the old peoples may have lower chewing force. Thus, clinical trial may be performed with this treatment protocol to use 4 fixtured ISP for old patients.

• Journal of Pharmaceutical Investigation
• /
• 제20권3호spc1호
• /
• pp.51-76
• /
• 1990

It is sometimes said lately that the pH of the human gastric juice is significantly different among individuals. Thus, the dissolution behavior of coated solid dosage forms should preferably be independent of the pH of the test solution. With these points as a background, the effect of pH on the dissolution velocity of coated tablets was studied to compare that of Pharmacoat with other gastric soluble film coating materials. Three viscosity types of Pharmacoat have been available(3, 6 and 15cP) until now. the 6cP type has been considered to be the most suitable for a tablet coating amongst the three types. The 3 cP type with a low degree of polymerization, is capable of providing high concentration, but the film strength is so inferior that sometimes cracking of the film may occur. On the other hand, in the case of the 15cP type, high polymer concentration cannot be achieved because of the high dgree of polymerization, and thus it is uneconomical for coating. Now, there is a strong demand to reduce the coating time even when HPMC is used in the 6cP type in order to reduce the coating cost. In order to improve this problem, we have concentrated our attention on reducing the viscosity value of HPMC to an allowable lower limit from 6cP. As a result of this study, it was found that the reduction of the viscosity value to around 4.5cP enabled the use of a higher solution concentration and an incidental shorter coating time without giving any substantial adverse effects on the properties of coated preparations. These experiment results are presented in the later part of this presentation. Based on this study, we have added the viscosity type of 4.5cP as one of the Pharmacoat products as Pharmacoat-645.