• Journal of Korea Foundry Society
• /
• v.20 no.4
• /
• pp.269-276
• /
• 2000

So far, the study on semi-solid process has been carried out to develop and research new advanced materials without some casting defects. In this study, A356 billets consisted of various dendritic shapes were prepared using electro-magnetic stirring process continuously. As-cast respectively has liquidus temperature of $625.6^{\circ}C$ and solidus temperature of $573.55^{\circ}C$ A356 slugs were reheated homogeneously at different temperatures of 580, 590 and $605^{\circ}C$, followed by squeezing in a mold insulated with applied pressures(0, 25, 50 and 70 MPa). In order to investigate on aging responce for casts, 50 MPa squeezed specimen among all specimens was prepared in aging treatments, which conditions are aging temperature of $160^{\circ}C$ and holding times of 0, 45, 90, 270, 360, 720, 1440 and 2880 min after solution treatment ($540^{\circ}C$ for 10 hr). SSM ingot with the output velocity of 150mm/min appeared more spheroidal shape and fine structure than that with the output velocity of 250 mm/min. According to increasing in reheating temperature, numbers of fatigue cycles, U.T.S and elongation increased at same time.

• Management & Information Systems Review
• /
• v.14
• /
• pp.181-193
• /
• 2004

This paper is concerned with the study of 'Knowledge Management', a paradigm of thought based on the idea that the future will be a knowledge-centered society. This paper also provides an overview of both 'what to manage' and 'how to manage' if an organization wants to develop in this environment. The process of 'Knowledge Management' begins with a decision. Presented with a myriad of information, of which we can't afford to obtain it all, what information is of value to the organization? Further, by systematically organizing not only the primary information but also that which was accumulated in the process, Knowledge Management is capable of suggesting a value-added plan of action. This research presents the necessary principles needed in order to successfully use Knowledge Management, specifically a harmony between the human and technological aspects. There cannot be a static solution to the problem, as the environment of the enterprise's problem is dynamic in nature. Throughout the process, the enterprise will constantly change its strategy and structure in order to adapt to variable knowledge, technology, strategy, regulations, consumer interest, etc... The essential constant of these problems is the importance of spending on education. Investments in educations help develope a infrastructure for Information Technology, the development of knowledge distribution strategies, and the creation of efficient Knowledge Management policy.

• Journal of the Korea Concrete Institute
• /
• v.11 no.3
• /
• pp.141-152
• /
• 1999

Precast prestressed double-tee slab may be designed by the PCI Design Handbook. It is based on the bridge construction and is required for reorganization for the use of buildings in the domestic construction environments. Much enhanced sections are developed from the reforming process on the determined design factors in the previous experimental works on double tees. Pre-determined shape, reinforcement detail, and 5000 psi concrete strength can not be expected as the best solution for the domestic construction requirements because large amount of use on that systems are anticipated. Flexural tests are performed on four full-scale 12.5m proto-type models, "least depth double tee", which are resulted from the optimization process. Domestic superimposed live load regulation, domestic material properties which is available to product, building design requirements and economy in construction are considered as the main factors to establish. the first two sections are double tee section for 1.2 ton/$\m^2$ market live load with straight and one-point depressed strands and the second two are for 0.6 ton/$\m^2$ parking live load with those strand types. All of the specimens tested fully comply with the flexural strength requirements as specified by ACI 318-95. However, the research has shown that following improved considerations are needed for better result in practice. The locations and method of connection for the lowest bottom mild bar, connection method between precast and cast-in-place concrete, and dap-end reinforcement are need to be improved.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.238-241
• /
• 2008

A brake system in automobile is one of the important parts that directly affect the safety of passengers. Particularly, disk brake module is applied to almost all kinds of automobile brake system due to its remarkable braking power and braking distance. In the disk brake module of an automobile, the bolt for tire wheel is assembled to the disk brake hub by interference fit (bolt pressing process). The process induces small deformation whose range is within tens of ${\mu}m$ and this deformation may cause the runout badness of the whole disk brake module, and even braking problems such as judder or squeal phenomena which makes the loss of braking efficiency. In this study, bolt pressing fit into hub was simulated by $ANSYS^{TM}$, a commercial structure analysis program. Also, the aspect and the cause of hub displacement were analyzed and the solution for decreasing runout of hub was proposed.

• Proceedings of the KAIS Fall Conference
• /
• 2001.11a
• /
• pp.107-110
• /
• 2001

Design process is the essential technology for development of industry in nation, but contrary to its significance the trial for development of design technology is not so active because it requires a lot of time and efforts to educate design engineers. For that reason, most of enterprises concentrated their efforts for improving product technologies to get instant effects in short periods, and through these trials considerable results could be achieved. Recently, however, many people realized that industrial development through only product technology without design technology has limits, accordingly, a lot of efforts, to educate machine designers whom have enough knowledge and ability on design through advanced design technology, concentrated for industrial development. In general, the curriculum of conventional education for machine design in most universities is mainly compose of three subjects, the theory for elements design, geometric modeling practice for mating engineering drawings using CAD software, and analysis of elements using CAE software fur determining whether proposed solution is correct or rational. Furthermore, because these three subject are provided for students as the completely separated subjects, most of students who have educated with this method have no enough ability to Integrate all design process into a comprehensive whole process. This paper proposes a new design education methodology through reverse engineering that can overcome these problems of conventional education method.

• Journal of the Korean institute of surface engineering
• /
• v.32 no.3
• /
• pp.447-451
• /
• 1999

Silver has the highest electrical conductivity of all metals and consequently this property is an attractive feature which makes it a leading candidate for use in electronic devices. The research conducted was focused primarily on the development of a process for obtaining a deposited silver-coating onto alumina, for applications related to electrical-conducting devices and, ancillarily, catalysts. Alumina balls and plane substrates were utilized for the investigation. The coating process employed an aqueous ammoniacal silver-nitrate electrolytes with a formaldehyde solution as the reductant. Modifying additives-an activator which would be expected to promote good deposition-characteristics onto the (dielectric) substrate and an inhibitor which would obviate homogeneous reduction (precipitation) of silver was observed when the activator-containing silver-electrolyte reductant constituents were combined. However, the silver-electrolyte/reductant system with inhibitor could be employed (at 8$0^{\circ}C$) to achieve a viable (subject to future research optimization) coating on alumina. The influence of the processing temperature on the deposition process was delineated during the course of the research. The morphology of the deposited-silver on the alumina balls was assessed by SEM imaging. A tape-peel test was employed, with the plane substrates, to semi-quantitatively characterize the adhesion to the alumina.

• Journal of the Korean Chemical Society
• /
• v.55 no.2
• /
• pp.268-278
• /
• 2011

Corrosion of aluminum in 0.1 M HCl solution in the absence and presence of ${\beta}$-blocker inhibitors (atenolol, propranolol, timolol and nadolol) was investigated using weight loss, potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques. The inhibition efficiency increased with inhibitor concentration and decreased with rise of temperature. Potentiodynamic polarization curves revealed that they acted as cathodic inhibitors. Some thermodynamic parameters were calculated and discussed. All inhibitors were adsorbed on Al surface obeying Frumkin isotherm. All EIS tests exhibited one capacitive loop which indicates that the corrosion reaction is controlled by charge transfer process. The inhibition efficiencies of all test methods were in good agreement.

• Economic and Environmental Geology
• /
• v.53 no.4
• /
• pp.337-346
• /
• 2020

This study was carried out to evaluate the applicability of the soil washing process to remediation mercury-contaminated mine tailing or solid material (soil and sediments etc.) around abandoned mines. First, the physicochemical characteristics of mine tailing were analyzed through particle size analysis and sequential extraction. Secondly, laboratory scale washing experiments were performed using hydrochloric acid, nitric acid, potassium iodide and sodium thiosulfate. As a results of particle size analysis, mine tailing particle were concentrated below 40 mesh and the particle size below 200 mesh was the most analyzed. As a result of sequential extraction, elemental mercury fraction was analyzed as the highest with 69.12%, with strongly bound fraction 15.25% and residual and HgS fractions 11.97%, respectively. Laboratory scale washing experiments showed low applicability for nitric acid and sodium thiosulfate solutions. In case of hydrochloric acid solution, it was analyzed that mercury removal was possible at particle size of 200 mesh or more. Therefore, it is considered to be performed together with the physical sorting process. Potassium iodide solution was analyzed to have high washing efficiency at all concentrations and particle sizes. In particular, the mercury removal efficiency is high in the micro particles, and thus the applicability of the washing technology is the highest.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.31 no.1
• /
• pp.51-64
• /
• 2013

When it comes to current growth trend for the printing process in Asia printing market, offset printing, gravure printing and screen printing are reduced respectively -4%, -19%, -55%. In judging from the fact, the change in the printing production system from mass production on small amount to small production on mass amount is the biggest issue. For this reason, digital printing shows the significant growth. According to the increase of the growth 78% for electro photography way and 67% for ink-jet, it's not enough to catch up with digital printing which is increasing as time goes by to equip with hardware like as digital press. There's been necessary to install the BOD(Book on Demand) system which is the advanced and regular publication edit solution based on web-to-print model in the prepress, and it has made the BOD system be considered in relation to maximization of efficiency and production. Therefore, this research tries to step forward from the POD concept, which is refired to "Print along with the ordered quantities, the ordered appropriate time and the demanded place", so that it could expand the range of the printing/publishing environment using the BOD system, the order-made publication based on automatically operating template. And it tried to make the relation to digital web press on ink-jet method which is adequate to "mass production on small amount" with such advanced concept. This research also aims to use actively BOD solution model to promote the productivity of labor, and then to produce the printings across all related industries, which means to manufacture maximally the products on the shortest time at minimum place through PC equipments.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.3
• /
• pp.280-285
• /
• 2005

The method of chemical absorption has been presented to separate and recover acid gases like $CO_2\;and\;H_2S$. But, this method has some problems such as loss of valuable amine and operational problems (forming, corrosion and fouling) by degradation. In this study, we investigated the degradation characteristics of aqueous AMP solution containing additives such as HMDA, MDEA and piperazine. The degradation was affected by temperature and process time. AMP solution absorbing $CO_2\;and\;H_2S$ was degraded 105% and 23% more than pure AMP at $120^{\circ}C$ respectively. In addition, all the additives were degraded significantly as the temperature increased. The order of the degraded amount of additives mixed in the AMP solution containing absorbed $CO_2$ was as followings : HMDA > piperazine > MDEA.