• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.7
• /
• pp.4357-4363
• /
• 2015

This study is to compare the differences of bonding strength based on the Degassing temperatures and various opaque materials for Ni-Cr alloy specimen which does not contain beryllium(Be). Numerous comparison tests have been performed to measure the bonding strength by experimenting 3-point flexural rigidity tests in order to find out ways of stabilization and enhancement of bonding strength between metal and porcelain. AVOVA, surface component observation experiment by SAM/EDS, and Tukey's HSAD posteriori tests results are as follows: First, The bonding strength in all groups has exceeded the minimum (25MPa) of ISO9693 bonding strength regulation for dental mental-porcelain specimen. Second, The bonding strength of Group V1 was $32.37{\pm}1.91MPa$, $38.25{\pm}1.38MPa$ in Group V2, $46.43{\pm}2.14MPa$ in Group V3 and $47.21{\pm}1.72MPa$ Group V4. The difference has been statistically meaningful. Tukey's HSAD posteriori tests results have shown that the bonding strength in Group V4 was higher than that of Group V1. Third, the bonding strength between metal and porcelain without degassing process was higher than that of with degassing process, and the bonding strength of powder opaque was higher than that of paste opaque. Fourth, Group V4 has ranked the highest on the comparison table of metal and porcelain bonding strength.

• Journal of the Korea Concrete Institute
• /
• v.14 no.5
• /
• pp.766-773
• /
• 2002

The failure phenomenon of overlaid concrete structures, such as surface crack, and peel-off failure, shear bond failure in the end contact zone, was investigated due to humidity changes. To investigate this failure phenomenon, the surface tensile stress, and the shear stress, the vertical tensile stress in the contact zone were analysed using the non-linear stress-strain relationship of material such as strain-hardening- and strain-softening diagrams. Overlay thickness and overlay material were the main variables in the analyses. It is assumed that the initial surface humidity of overlaid concrete structures was 100％ r.H. With a atmospheric humidity of 55％ r.H. and two load cases for drying(LCI), curing and drying(LC2), the stress states of overlaid concrete structures were calculated. The result shows that only fictitious cracks occurred in the overlay surface of CM2O, ECM25, and no shear bond failure occurred in the contact zone without CM2O. The peel-off failure was proved to be the main cause of the damage in the overlaid concrete structures. Only for overlay thickness of 1cm occurred no peel-off failure in the case of drying after a long-term public use(LC1). In the case of curing and drying during overlay work(LC2) occurred the peel-off failure within 1.5days for all the overlaid concrete structures.

• Bulletin of the Korean Chemical Society
• /
• v.15 no.11
• /
• pp.990-996
• /
• 1994

New ferrocene-based chelate amines, $Fe[C_5H_4CH(Me)NMe_2]_2\;(3), \;Fe[C_5H-3(CH(Me)NMe_2)(PPh_2)-1,2]_2\;(4),\;(C_5H_5)Fe(C_5H_3(CH_2NMe_2)(CH(CN)NMe_2-1,2)\;(6),\;and\;(C_5H_5)Fe(C_5H_3(CH_2NMe_2)(CH(Me)NMe_2-1,2)$ (7) have been prepared. The reaction and the coordination chemistry of 4 and other related compounds (S,R)-(1-N,N-dimethylaminoethyl)-2-dicyclohexylphosphino)ferrocene (CPFA) and 1,1'-bis-(diphenylphosphino)ferrocene (BPPF) with $Rh_2(OAc)_4(MeOH)_2$ were investigated. The reaction of the chiral ligand (S,R)-CPFA forms a complex of the type (${\eta}^1$-(S,R)-CPFA-P)$_2Rh_2(OAc)_4$ (8) in which the ligand is coordinated to both rhodium centers in a monodentate fashion through phosphorus. In contrast, the bisphosphine analogues such as BPPF and 4 afford chelate complexes of the type (${\eta}^2-PP)Rh_2(OAc)_4$ (9 & 10) where both ligands act as a chelate bidentate to a single rhodium atom. All these complexes were characterized by microanalytical and spectroscopic techniques. In one case, the structure of 8 was determined by X-ray crystallography. Crystals are monoclinic, space group C2 (No. 5), with a=26.389 (3), b=12.942 (1), c=11.825 (1) A, ${\beta}$=111.22(1)$^{\circ}$, V=3964.7 (8) $A^3$, Z=4, and $D_{calc}$=1.58 g $cm^{-3}$. Two Rh(II) centers are bridged by four $AcO^-$ groups in the ${\eta}^1$ : ${\eta}^1$ mode across a Rh-Rh single bond, and octahedral coordination at Rh(1) and Rh(1') is completed by axially coordinating (S,R)-CPFA and a briding $AcO^-$, respectively.

• Journal of the Korean Society of Industry Convergence
• /
• v.7 no.1
• /
• pp.107-113
• /
• 2004

Several transition metal complexes, [$M(L)X_2$](M=Pd(II), Ni(II); X=CI, Br) are prepared with aminophosphine ligands such as 1,2-bis{(diphenylphosphino)amino}ethane{$Ph_2PNHCH_2CH_2NHPPh_2$}($L_1$), 1,2-bis{(diphenylphosphino)amino}propane{$Ph_2PNHCH(CH_3)CH_2NHPPh_2$}($L_2$), trans-1,2-bis{(diphenylphosphino)amino}cyclohexane{$Ph_2PNHC_6H_{10}NHPPh_2$}($L_3$) and 1,2-bis{(diphenylphosphino)amino}benzene{$Ph_2PNHC_6H_4NHPPh_2$}($L_4$). The properties of these complexes are characterized by optical spectroscopic methods including UV/vis spectroscopy, CD, IR, $^1H$- and $^{31}P-NMR$ together with conductometer and elemental analysis. All complexes are stable under atmospheric environment. Catalytic reactivity for C-C coupling between [$M(L)X_2$] and Grignard reagents(RMgX; R=phenyl, propyl, buthyl) by thermolysis were investigated utilizing GC/mass, $^1H$- and $^{13}C-NMR$. When mol scale is 1:20 at [$Pd(L)Cl_2$] and Grignard reagents, the high catalytic activity for C-C coupling is apparent. The [$M(L)X_2$](X=Cl, Br) complexes which have strong bond at M-P exhibit high yields for C-C coupling reactions. When the central metal ion is Pd(II), the high catalytic activity for C-C coupling is apparent. The complex coordinated with Br shows higher catalytic activity for C-C coupling reactions compared to Cl.

• Rapid Communication in Photoscience
• /
• v.3 no.4
• /
• pp.70-72
• /
• 2014

Visible-light irradiation of MeCN solution containing di(hydroxo)metallo(tetraphenyl)porphyrin complex $(tppM(OH)_2$: 1a; $M=Sb(V)^+Br^-$, 1b; $M=P(V)^+Cl^-$, 1c; M=Ge(IV)) and 2-mercaptoethanol (2-ME) as a substrate under aerated condition gave bis(2-hydroxyethyl)disulfide (2-HEDS) as an oxidative product of 2-ME. It is indicated that the oxidation of 2-ME should proceed with a photocatalytic process by 1, because the turn over number (TON) for the formation of 2-HEDS was over unit. The TON was determined to be 642 as a maximum value when 1a was used as a sensitizer. The formation of 2-HDES was extremely slow under argon atmosphere. The fluorescence of 1 was not quenched by 2-ME at all, and the free energy change (${\Delta}G$) with electron transfer (ET) from 2-ME to excited triplet state of $1(^31^*)$ was estimated as a negative value. The quenching rate constant ($k_r$) of $^31^*$ by 2-ME, obtained by the kinetics for the formation of 2-HEDS, strongly depends on ${\Delta}G$. These findings indicate that 1-sensitized oxidation was initiated by photoinduced ET from 2-ME to $^31^*$ to generate both radical cation of 2-ME ($2-ME^{+\bulle}$) and porphyrin radical anion ($1^{-\bulle}$), resulting that the formation of 2-HEDS can be proceeded by the dimerization of $2-ME^{+\bulle}$, and through a catalytic cycle due to returning to 1 by the ET from $1^{-\bulle}$ to molecular oxygen.

• The Journal of Korean Academy of Prosthodontics
• /
• v.41 no.3
• /
• pp.369-378
• /
• 2003

Statement of Problem: Recently, resin cements have become more widely used and have been accepted as prominent luting cements. Current resin cements exhibit less microleakage than conventional luting cements. However, the constant contact with water and exposure to occlusal forces increase microleakage even in resin cements inevitably. Most bonding resins have been modified to contain a hydrophilic resin such as 2-hydroxyethylmethacrylate (HEMA) to overcome some of the problems associated with the hydrophobic nature of bonding resins. By virtue of these modifications, bonding resins absorb a significant amount of water, and there may also be significant stresses at bonding interfaces, which may adversely affect the longevity of restorations. Therefore the reinforcement of water stability of resin cement is indispensable in future study. Purpose: This study was conducted to examine the influence of water retention on microleakage of two resin cements over the period of 6 months. Materials and Methods: 32 extracted human teeth were used to test the microleakage of a single full veneer crown. Two resin cements with different components and adhesive properties - Panavia F (Kuraray Co., Osaka, Japan) and Super-Bond C&B (Sun Medical Co., Kyoto, Japan)- were investigated. The storage medium was the physiological saline solution changed every week for 1 month, 3 months, and 6 months. One group was tested after storage for 1 day. At the end of the each storage period, all specimens were exposed to thermocycling from $5^{\circ}C$ to $55^{\circ}C$ of 500 cycles and chewing simulation of 50,000 cycles, and then stained with 50% silver nitrate solution. The linear penetration of microleakage was measured using a stereoscopic microscope at ${\times}40$ magnification and a digital traveling micrometer with an accuracy of ${\pm}3{\mu}m$. Values were analyzed using two-way ANOVA test, Duncan's multiple range tests (DMRT). Results : Statistically significant difference of microleakage was shown in the 3-month group compared with the1-day or 1-month group in both systems (p<0.05) and there were statistically significant differences in microleakage between the 3-month group and the 6-month group in both systems (p<0.05). The two systems showed different tendency in the course of increased microleakage during 3 months. In Panavia F, microleakage increased slowly throughout the periods. In Super-Bond C&B, there was no significant increase of microleakage for 1 month, but there was statistically significant increase of microleakage for the next 2 months. For the mean microleakage for each period, in the 3-month group, microleakage of Super-Bond C&B was significantly greater than that of Panavia F. On the other hand, in the 6-month group, microleakage of Panavia F was significantly greater than that of Super-Bond C&B (p<0.05). Conclusion: Within the limitation of this study, water retention of two different bonding systems influence microleakage of resin cements. Further studies with the longer observation periods in viro are required in order to investigate water stability and the bonding durability of the resin cement. CLINICAL IMPLICATIONS Microleakage at the Cement-tooth interfaces did not necessarily result in the failure of the crowns. But it is considered to be a major factor influening the longerity of restorations. Further clinical approaches for decreasing the amount of microleakage are required.

• Bulletin of the Korean Chemical Society
• /
• v.2 no.2
• /
• pp.71-75
• /
• 1981

Vacuum ultraviolet photolysis of ethyl bromide was studied at 104.8-106.7 nm (11.4-11.6 eV) in the pressure range of 0.2-18.6 torr at $25^{\circ}$ using an argon resonance lamp with and without additives, i.e., NO and He. Since the ionization potential of $CH_3CH_2Br$ is lower than the photon energy, the competitive processes between the photoionization and the photodecomposition were also investigated. The observations indicated that 50% of absorbed light leads to the former process and the rest to the latter one. In the absence of NO the principal reaction products for the latter process were found to be $CH_4, C_2H_2, C_2H_4, C_2H_6, and C_3H_8$. The product quantum yields of these reaction products showed two strikingly different phenomena with an increase in reactant pressure. The major products, $C_2H_4$ and $C_2H_6$, showed positive effects with pressure whereas the effects on minor products were negative in both cases, i.e., He and reactant pressures. Addition of NO completely suppresses the formation of all products except $C_2H_4$ and reduces the $C_2H_4$ quantum yield. These observations are interpreted in view of existence of two different electronically excited states. The initial formation of short-lived Rydberg transition state undergoes HBr molecular elimination and this state can across over by collisional induction to a second excited state which decomposes exclusively by carbon-bromine bond fission. The estimated lifetime of the initial excited state was ${\sim}4{\times}10^{-10}$ sec. The extinction coefficient for $CH_3CH_2Br$ at 104.8-106.7 nm and $25{\circ}$ was determined to be ${varepsilon} = (1/PL)ln(I_0/I_t) = 2061{\pm}160atm^{-1}cm6{-1}$ with 95% confidence level.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.15 no.2
• /
• pp.357-363
• /
• 1995

Disbond size of adhesively bonded single lap and double lap joints CFRP composite specimens has been evaluated using acousto-ultrasonic(AU) technique. Frequency spectra for all specimens were obtained by measuring peak amplitude of the stress wave propagated through the bond-lines. By analyzing these frequency spectra, peak amplitude was found to be proportional to fractional bonding area and to be maxima at the fundamental and the third order higher harmonic frequencies of specimen thickness mode. The disbond size can be evaluated quantitatively and this technique can be applied to real structures if the reference specimens are prepared in advancve.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.1
• /
• pp.98-102
• /
• 2002

The structure of a single crystal, grown by a slow cooling a melt of $Ca_{1.29}Bi_{0.14}VO_4$ composition, was analyzed. The crystals belong to the rhombohedral space group R3c and the dimensions of the unit cells are a = 10.848(1)${\AA}$, c = 38.048(6)${\AA}$, V = 3877.6(8)${\AA}^3$ for the pale yellow crystal, and a = 10.857(1), c = 38.063(6)${\AA}$, V = 3885.6(8)${\AA}^3$ for the yellow crystal, respectively. Unit cell dimensions of the crystal were larger than those of the host crystal, $Ca_3(VO_4)_2$, owing to the Bi that replaced Ca in the unit cell. Ca in the unit cell formed six, eight and nine coordinated polyhedra with O atoms and Bi replacing Ca entered the eight or nine coordinated Ca sites with different crystallographic environments in the unit cell. All the V in the unit cell formed four coordinated tetrahedra with O atoms, however V-O bond lengths in the tetrahedra were different from one another.

• Journal of the Korean Ceramic Society
• /
• v.55 no.6
• /
• pp.581-589
• /
• 2018

This work concentrated on the effect of different laser beams on the microstructure and dielectric properties of $BaTiO_3$ nanoparticles at different calcinations times during the gelling preparation step. The nanoparticles were prepared by the sol-gel method. A green (1000 mW, 532 nm) and red laser beam (500 mW, 808 nm), were applied vertically at the center of stirring raw materials. The samples were sintered at $1000^{\circ}C$ for 2, 4, and 6 h. X-ray diffraction (XRD) analysis showed that samples prepared under the green laser have the highest purity. The FT-IR spectra showed that the stretching and bending vibrations of TiO bond without any other bonds, which are compatible to the X-ray diffraction (XRD) results. Samples were characterized by transmission electron microscopy (TEM), Scan electron microscopy (SEM), and UV-Visible spectrophotometer. Characterization showed the samples prepared under the green laser to have the highest particle size (~ 50 nm) and transparency for all sintering durations. Laser beam effects on electrical characterization were studied. BT nanoparticles prepared under the green laser show the higher dielectric constant, which was found to increase with sintering temperature.