• 한국생산제조학회지
• /
• 제25권6호
• /
• pp.440-444
• /
• 2016

Owing to the introduction of various IT devices with emphasis on portability and design, the TFT (thin film transistor liquid crystal display) panel applied to IT devices has the same shape as the product, and the portability requirement of IT devices has resulted in a need for panels with higher rigidity. In this study, the effect of grinding conditions such as the feed rate and edge speed of edge grinding on the surface roughness and chipping of the machined surface is investigated using a metal bond wheel. During edge grinding of alkari-free glass, weak mechanical property of glass results in big chipping owing to generation of tensile stress at the end of grining operation. The results of this study show that the grinding characteristics of alkali-free glass are obtained and meet industry requirements.

• 마이크로전자및패키징학회지
• /
• 제10권4호
• /
• pp.47-52
• /
• 2003

PDP전극용 Ag전극 페이스트의 프릿으로 기존의 Pb-based 프릿을 대신 할 수 있는 Bi-based 조성의 새로운 유리조성의 가능성을 검토하였다. PDP디스플레이 응용을 위해 프릿의 저융점화 및 열팽창계수 제어를 행하였고, 이를 전극 페이스트 제조에 적용하여 스크린 프린팅된 전극을 평가하였다. $Bi_2O_3$를 50-60wt%이상 첨가된 $Bi_2O_3-B_2O_3-Al_2O_3$계 조성의 프릿은 연화점이 400∼$480^{\circ}C$, 열팽창계수가 7.31∼$10.02\times 10^{-6}/^{\circ}C$이며, 전극의 단자저항은 4.1∼4.8$\Omega$ 이었다. 본 연구에서 새로이 개발된 Bi계 프릿조성은 Pb계 조성의 프릿에 상당하는 물성을 얻을 수 있었으며, 이를 전극용 페이스트에 적용한 결과, 전극 프린팅에서 퍼짐성과 균일성이 우수하였다. PDP전극용 무연, 무 알카리 프릿으로 Bi계 조성의 적용가능성을 확인할 수 있었다.

• 한국세라믹학회지
• /
• 제32권3호
• /
• pp.385-393
• /
• 1995

Akali-resistant porous glass was prepared by phase separation in Na2O-B2O3-SiO2 system containing ZrO2 and MgO. ZrO2 was added for alkali-resistance and MgO for anti-cracking during leaching. Optimal content of ZrO2 for alkali-resistance was 7wt% and devitrification by heat treatment resulted from further addition. Pore size and pore volume were decreased and specific surface area was increased with ZrO2 addition due to depression in phase separation. Addition of 3mol% MgO to mother glass containing 7wt% ZrO2 was effective for anti-crack during leaching. In this case, with phase separation at 55$0^{\circ}C$ and 5$25^{\circ}C$ for 20 hrs. crack-free porous glasses could be prepared. The relation between pore size r and heat treatment time t at 55$0^{\circ}C$ was D=25.58＋18.16t. According to measurement of gas permeability, the mechanism of gas permeation was Knudsen flow. N2 and He permeability of porous glass which was prepared by heat treatment at 55$0^{\circ}C$ for 20 hrs. were 0.843$\times$10-7mol/$m^2$.s.Pa and 2.161$\times$10-7mol/$m^2$.s.Pa respectively.

• 한국세라믹학회지
• /
• 제33권4호
• /
• pp.385-390
• /
• 1996

The electrical resistivity of the ceramic glaze coated on ceramic substrate plays an important role on the characteristics of the thick and thin film electrical circuits. In this study the effects of the various modifiers on the electrical resistivity were examined in SiO2-Al2O3-B2O3-RO-Na2O (RO=CaO , SrO, BaO, PbO) glass system. In alkali free glasses where divalent cations are responsible for electrical conduction the electrical conductivity of th glasses increased with the ionic size of divalent cations due to the decrease in the bond strength between oxyben and divalent cation. In Na2O containing glasses however where Na+ ion is responsible for electrical conduction the ionic conductivity decreased with the ionic size of divalent cations because the blocking effect of the cations on Na+ ion movement increased with larger divalent cations. Na+ ionic conduction also depended on the glass structure relaxation due to the corrdination number changes of B2O3 and Al2O3 which varied with the NaO2 content in the glass.

• 한국생산제조학회지
• /
• 제25권1호
• /
• pp.14-20
• /
• 2016

This paper describes a green stripping process to effectively strip the remaining DFR layer on a non-alkali-based ITO glass surface after an etching process. A stripper, water-soluble amine compound, is used to investigate the characteristics of stripping ability and to suggest a valid method for the green process. Increasing the composition (5-30% concentration) of the ethanol amine-based stripper was found to greatly reduce the stripping time applied in the dipping method. The composition (30%) achieved an excellent stripping effect and free-residue impurities. Additionally, it was possible to obtain the effect of stripping in a way to sustain the release before generating DFR sludge from the ITO glass surface by using dipping condition (stripping time) in the composition. An Additional stripping process (buffering) out of dipping can realize productivity improvement and cost reduction because of the higher proportion of re-use of the stripping solution used in the DFR removal step.

• Structural Engineering and Mechanics
• /
• 제75권1호
• /
• pp.123-131
• /
• 2020

The bond performance of glass fibre reinforced polymer (GFRP) bars and that of steel bars embedded in Alkali Activated Cement (AAC) concrete are analysed and compared using pull-out specimens. The bond failure modes, the average bond strength and the free end bond stress-slip curves are used for comparison. Tepfers' concrete ring model is used to further analyse the splitting failure in ribbed steel bar and GFRP bar specimens. The angle the bond forces make with the bar axis was calculated and used for comparing bond behaviour of ribbed steel bar and GFRP bars in AAC concrete. The results showed that bond failure mode plays a significant role in the comparison of the average bond stress of the specimens at failure. In case of pull-out failure mode, specimens with ribbed steel bars showed a higher bond strength while specimens with GFRP bars showed a higher bond stress in case of splitting failure mode. Comparison of the bond stress-slip curves of ribbed steel bars and GFRP bars depicted that the constant bond stress region at the peak is much smaller in case of GFRP bars than ribbed steel bars indicating a basic bond mechanism difference in GFRP and ribbed steel bars.

• International Journal of Concrete Structures and Materials
• /
• 제10권3호
• /
• pp.337-353
• /
• 2016

The successful completion of the present research would be achieved using ground waste glass (GWG) microparticles in self-consolidating concrete (SCC). Here, the influences of GWG microparticles as cementing material on mechanical and durability response properties of SCC are investigated. The aim of this study is to investigate the hardened mechanical properties, percentage of water absorption, free drying shrinkage, unit weight and Alkali Silica Reaction (ASR) of binary blended concrete with partial replacement of cement by 5, 10, 15, 20, 25 and 30 wt% of GWG microparticles. Besides, slump flow, V-funnel, L-box, J-ring, GTM screen stability, visual stability index (VSI), setting time and air content tests were also performed as workability of fresh concrete indicators. The results show that the workability of fresh concrete was increased by increasing the content of GWG microparticles. The results showed that using GWG microparticles up to maximum replacement of 15 % produces concrete with improved hardened strengths. From the results, when the amount of GWG increased there was a gradual decrease in ASR expansion. Results showed that it is possible to successfully produce SCC with GWG as cementing material in terms of workability, durability and hardened properties.

• 한국세라믹학회지
• /
• 제52권2호
• /
• pp.150-153
• /
• 2015

Recently, research on geopolymeric concrete that does not use cement as a binder has been actively investigated. Geopolymeric concrete is cement-free concrete. Masato, ocher and/or soil has been solidified into geopolymeric concrete by the reaction of specifically modified silicate as an alkali activator and inorganic binding materials such as blast furnace slag, fly ash or meta-kaolin, which is cured at room temperature to exhibit high compressive strengths. Based on the results, this study shows how geopolymeric concrete that uses specifically modified silicate and inorganic binding materials is implemented as eco-cement with no cement.

• 한국광물학회지
• /
• 제24권4호
• /
• pp.301-312
• /
• 2011

철을 포함한 비정질 규산염 용융체의 원자 구조 규명은 지표 환경의 화성활동 및 맨틀 심부의 초저속도층의 속도구조에 이르는 광범위한 지질과정의 미시적인 원인에 대한 단서를 제공한다. 본 연구에서는 철을 포함한 비정질 규산염의 원자 구조 규명에 가장 적합한 고상 핵자기공명분광분석(NMR)을 이용하여 최대 16.07 wt%의 $Fe_2O_3$가 포함된 비정질 알칼리 규산염(iron-bearing alkali silicate glasses)의 철의 함량 변화가 원자구조에 미치는 영향을 규명하였다. $^{29}Si$ 스핀-격자 완화시간($T_1$)을 측정한 결과, 철의 함량에 따라 스핀-격자 완화시간이 짧아지는데 이는 철이 가지고 있는 홀전자(unpaired electron)와 핵 스핀(nuclear spin)간의 상호작용으로부터 기인한다. $^{29}Si$ MAS NMR 실험 결과, 철이 포함되지 않은 시료의 경우 $Q^2$, $Q^3$ 그리고 $Q^4$의 환경을 지시하는 피크가 분리됨에 반하여, 철이 포함된 시료의 경우 NMR 신호의 급격한 감소와 피크 폭이 넓어짐으로써 각각의 규소 환경이 거의 분리되지 않았다. 그러나 철의 함량에 따라 스펙트럼이 넓어지고 화학적 차폐값(chemical shift)이 높아지는 현상을 확인하였는데, 이는 $Q^4$의 규소 환경을 나타내는 방향으로서 철 주변의 $Q^n$이 불균질하게 분포하고 있음을 지시한다. $^{17}O$ MAS NMR 실험에서도 철이 포함되지 않은 시료에서는 연결산소(Si-O-Si)와 비연결산소(Na-O-Si)가 부분적으로 분리되지만, 철의 함량이 증가하면서 각각의 산소 환경이 거의 분리되지 않는다. 이러한 연구결과는 고상 핵자기공명분광분석이 철을 포함한 비정질 규산염의 상세한 구조 연구에 효과적인 도구임을 지시한다.

• 공업화학
• /
• 제5권3호
• /
• pp.406-412
• /
• 1994

Water glass로부터 ${\delta}-Na_2Si_2O_5$를 합성하여, 이의 칼슘과 마그네슘의 이온교환성, 이온교환에 대한 열역학적 특성치를 조사하였다. Water glass로부터 합성한 ${\delta}-Na_2Si_2O_5$의 최적 합성온도가 $725^{\circ}C$ 근처임을 알았다. 이온교환반응에 있어서 마그네슘 이온교환능이 칼슘 이온교환능보다 우수하였고, 마그네슘의 이온교환능은 온도에 민감하지 않은 반면에, 칼슘의 이온교환능은 온도에 민감하여 온도증가에 따라 이온교환능의 증가폭이 큼을 알 수 있었다. 초기 수용액 pH 변화에 따른 칼슘과 마그네슘의 이온교환능은 초기 수용액 pH가 2~6 사이에서 약간 감소하였으나, 6 이상에서는 ${\delta}-Na_2Si_2O_5$의 알카리 완충효과 때문에 각각 일정하게 나타났다. 이온교환 Gibbs 자유에너지는 이온교환 선택성의 역순으로 칼습 이온 교환반응이 마그네슘 이온교환반응보다 높게 나타났으며, 엔탈피와 엔트로피값도 칼슘 이온교환반응이 마그네슘 이온교환 반응보다 높게 나타났다.