• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.5
• /
• pp.179-189
• /
• 2008

The performance of Lean NOx Trap (LNT) based on the catalysts of Pt/K/Ba/$\gamma-Al_2O_3$ with proprietary washcoat formulation is studied using a bench flow reactor system. To investigate the effect of temperature and gas hourly space velocity (GHSV) on the nitrogen oxides (NOx) trapping capacity as well as NOx breakthrough time and final ratio of $NO_2$ to NO of LNT, series of adsorption isotherms are carried out with simulated exhaust gases of the lean burn engines. Since typical operation of LNT requires periodic regeneration with a short rich excursion, where the stored or trapped NOx is released and subsequently reduced to $N_2$, the effect of the duration of lean and rich phase and type of reductants on the NOx conversion is investigated. NOx storage capacity and breakthrough time obtained from adsorption isotherms shows a volcano-type dependence on the temperature with a maximum NOx storage capacity occurring $350^{\circ}C$ and with a maximum breakthrough time occurring $400^{\circ}C$ at all GHSVs investigated in this study. Also, maximum ratio of $NO_2$ to NO is obtained at $400^{\circ}C$ with a GHSV of $75,000\;hr^{-1}$ Lean/rich cycle of 100 s lean and 5 s rich used with a concentration of 1.33% of $H_2$ and 4% of CO in the rich phase is found to be optimum at operating temperature of $350^{\circ}C$ and a GHSV of $50,000\;hr^{-1}$.

• Transactions of the Korean hydrogen and new energy society
• /
• v.18 no.1
• /
• pp.52-59
• /
• 2007

We investigated the effects of the addition of Mn and $AB_5$ type alloy on the electrochemical characteristics of Ti-Cr-V BCC type alloys as anode materials for Ni-MH battery. The activation behavior and discharge capacity of the BCC type alloys were significantly improved by ball-milling with the $LmNi_{4.1}Al_{0.25}Mn_{0.3}Co_{0.65}$ alloy, because the $AB_5$ type alloy acted as hydrogen path on the surface of the BCC type alloy. Among the Mn substituted alloys($Mn=0.03%{\sim}0.08%$), the $Ti_{0.32}Cr_{0.38}Mn_{0.05}V_{0.25}$ alloy ball-milled with $AB_5$ type alloy exhibited the greatest discharge capacity of $336\;mAh{\cdot}g^{-1}$. In addition, Mn substituted alloys exhibited the lower plateau pressure in P-C- T curve, the better hydrogen storage capacity and faster surface activation compared with the alloy without Mn.

• International Journal of Advanced Culture Technology
• /
• v.3 no.1
• /
• pp.153-160
• /
• 2015

This article is aimed to study the effects of resistance spot welding (RSW) on the lap joint properties between AA1100 aluminum alloy and SGACD zinc coated steel and its properties. The summarized experimental results are as follows. The summarized experimental results are as follows. The optimum welding parameters that produced maximum tensile shear strength of 2200 N was a welding current of 95 kA, a holding time of 10 cycles, and a welding pressure of 0.10 MPa. Increasing of welding current, increased the tensile shear strength of the joint and also increased the amount of aluminum dispersion at the joint interface. The lap joint of steel over the aluminum (Type I) showed the higher joint tensile shear strength than a lap joint of aluminum over the steel (Type II). The indentation depth and the ratio of the indentation depth to the plate thickness decreased when the welding current was increased in the type I lap joint and also decreased when the welding current was decreased in the type II lap joint. The interface structure showed the formation of the brittle $FeAl_3$ intermetallic compound that deteriorated the joint strength.

• Archives of Pharmacal Research
• /
• v.28 no.5
• /
• pp.550-556
• /
• 2005

The flower of Campsis grandiflora K. Schum. Was extracted with 80% aqueous MeOH, and the concentrated extract was partitioned with EtOAc, n-BuOH and H$_2$O. From the EtO Ac fraction, seven triterpenoids were isolated through the repeated silica gel, ODS column chromatographies and preparative HPLC. From the result of physico- chemical data including NMR, MS and IR, the chemical structures of the compounds were determined as 3${\beta}$-hydroxyolean-12-en-28-oic acid (oleanolic acid, 1), 3${\beta}$-hydroxyurs-12-en-28-oic acid (ursolic acid, 2), 3${\beta}$-hydroxyurs-12-en-28-al (ursolic aldehyde, 3), 2${\alpha}$,3${\beta}$-dihydroxyolean-12-en-28-oic acid (maslinic acid, 4), 2${\alpha}$,3${\beta}$-dihydroxyurs-12-en-28-oic acid (corosolic acid, 5), 3${\beta}$,23-dihydroxyurs-12- en-28-oic acid (23-hydroxyursolic acid ,6) and 2${\alpha}$,3${\beta}$,23-trihydroxyolean-12-en-28- oic acid (arjunolic acid, 7). These teriterpenoids were isolated for the first time from this plant. Also, compounds 4, 5, 6, and 7 revealed relatively high hACAT-1 inhibitory activity with the value of 46.2${\pm}$1.1, 46.7${\pm}$0.9, 41.5${\pm}$1.3 and 60.8${\pm}$1.1% at the concentration of 100${\mu}$g/mL, respectively.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.1
• /
• pp.40-44
• /
• 2017

The effect of weak dielectric silicone dioxide($SiO_2$) embedded in polyfluorene(PFO) emitting layer of polymer-based multi structure OLED was investigated. Indium tin oxide(ITO)/poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS)/poly(9,9-di-n-octylfluorenyl-2,7-diyl)(PFO)/2,2,2"-(1,3,5-benzinetriyl)-tris(1-phenyl-1-H-benzimidazole) (TPBi)/aluminum(Al) structure OLED was fabricated by spin-coating method. Applied electric field causes some effect on $SiO_2$ in PFO layer. Thus, interaction between polymers and affected $SiO_2$ might generate electrical and luminance properties change. Experimental results, show the reduced threshold voltage of 6 V(from 23 V to 17 V). The maximum current density was rather increased from $71A/m^2$ to $610A/m^2$ and maximum brightness was also increased from $7.19cd/m^2$ to $41.03cd/m^2$, 9 and 6 times each. Additionally we obtained colour broadening result due to the increasing of blue-green band emission. Consequently we observed that electrical and luminance properties are enhanced by adding $SiO_2$ and identified the possibility of controlling the emission colour of OLED device according to colour broadening.

• Management & Information Systems Review
• /
• v.31 no.4
• /
• pp.377-395
• /
• 2012

The purposes of this research was to examine the relationship between two forms of satisfaction, commitment and turnover intentions at organization, job. Also consistent with the Meyer et al(1993) notion of the three-component model of organizational commitment. Although researchers have examined organizational commitment in relation to a wide range of variables, there has been no discriminant validity of commitment at occupation and job. The purpose of the present article, are to compare the relation between satisfaction forms, commitment forms and turn intentions forms. Confirmatory factor analysis supported the proposed distinction between the three forms of commitment and two turnover intentions forms at the measurement level in the distribution industry(N=156). Results using structural equation analysis with AMOS18 showed that job satisfaction had an positive impact on job commitment forms. Organizational satisfaction positive impact on two turnover intentions forms. However it revealed that no significant relation between organizational satisfaction and job commitment, job commitment and job turnover intentions.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1523-1525
• /
• 2003

Due to the rapid development of wireless networking system, researches on the communication devices are mainly focus on microwave frequency devices such as filters, resonators, and phase shifters. Among them, Film bulk acoustic resonator (FBAR) has been paid extensive attentions for their high performance. In this research, ZnO thin films were deposited by RF-magnetron sputtering on Al/$SiO_2$/Si wafer and then crystalline properties and surface morphology were examined. To measure crystalline structure and surface morphology X-ray diffraction (XRD) and Scanning Electron Microscope (SEM) were employed. It was showed that crystalline properties of ZnO thin films were strongly dependant on the deposition conditions. As increasing the deposition temperature and the deposition pressures, the peak intensities of ZnO(002) plane were increased until $300^{\circ}C$, then decreased rapidly. At the sputtering conditions of RF power of 213 W and working pressure of 15 m Torr, ZnO film had excellent c-axis orientation, surface morphology, and adhesion to the substrate. In conclusion we optimized smooth surface with very small grains as well as highly c-axis oriented ZnO film for FBAR applications.

• Journal of the Korean Society of Safety
• /
• v.23 no.5
• /
• pp.54-60
• /
• 2008

The objective of this study is to obtain the optimal process condition and the maximum decomposition efficiency by measuring the decomposition efficiency, electricity consumption, and voltage in accordance with the change of the process variables such as the frequency, maintaining time period, concentration, electrode material, thickness of the electrode, the number of windings of the electrode, and added materials etc. of the harmful atmospheric contamination gases such as NO, $NO_2$, and $SO_2$ etc. with the plasma which is generated by the discharging of the specially designed and manufactured $TiO_2$ catalysis reactor and SPCP reactor. The decomposition efficiency of the NO, the standard samples, is obtained with the plasma which is being generated by the discharge of the combination effect of the $TiO_2$ catalysis reactor and SPCP reactor with the variation of those process variables such as the frequency of the high voltage generator($5{\sim}50kHz$), maintaining time of the harmful gases($1{\sim}10.5sec$), initial concentration($100{\sim}1,000ppm$), the material of the electrode(W, Cu, Al), the thickness of the electrode(1, 2, 3mm), the number of the windings of the electrode(7, 9, 11turns), basic gases($N_2$, $O_2$, air), and the simulated gas($CO_2$) and the resulting substances are analyzed by utilizing FT-IR & GC.

• Transactions on Electrical and Electronic Materials
• /
• v.1 no.4
• /
• pp.11-15
• /
• 2000

This paper presents a process optimization of antireflection (AR) coating on crystalline Si solar cells. Theoretical and experimental investigations were performed on a double-layer AR(DLAR) coating of MgFe$_2$/GeO$_2$. We investigated GeO$_2$ films as an AR layer because they have a proper refractive index of 2.46 and demonstrate the same lattice constant as Si substrate. RF sputter grown GeO$_2$ film showed deposition temperature strong dependence. The GeO$_2$ at 400$\^{C}$ exhibited a strong (111) preferred orientation and the lowest surface roughness of 6.87 $\AA$. Refractive index of MgFe$_2$film was measured as 1.386 for the most of growth temperature. An optimized DLAR coating showed a reflectance as low as 2.04% in the wavelengths ranged from 0.4 ㎛ to 1.1 ㎛. Solar cells with a structure of MgFe$_2$/GeO$_2$/Ag/N$\^$+//p-type Si/P$\^$+//Al were investigated with the without DLAR coatings. We achieved the efficiency of solar cells greater than 15% with 3.12% improvement with DLAR coatings. Further details about MgFe$_2$,GeO$_2$ films, and cell fabrication parameters are presented in this paper.

• Restorative Dentistry and Endodontics
• /
• v.46 no.4
• /
• pp.52.1-52.11
• /
• 2021

Objectives: This study evaluated the effects of low and moderate concentrations of triple antibiotic paste (TAP) and double antibiotic paste (DAP) loaded into a hydrogel system on crown discoloration and explored whether application of an adhesive bonding agent prevented crown discoloration. Materials and Methods: Intact human molars (n = 160) were horizontally sectioned 1 mm apical to the cementoenamel junction. The crowns were randomized into 8 experimental groups (calcium hydroxide, Ca[OH]₂; 1, 10, and 1,000 mg/mL TAP and DAP; and no medicament. The pulp chambers in half of the samples were coated with an adhesive bonding agent before receiving the intracanal medicament. Color changes (ΔE) were detected by spectrophotometry after 1 day, 1 week, and 4 weeks, and after 5,000 thermal cycles, with ΔE = 3.7 as a perceptible threshold. The 1-sample t-test was used to determine the significance of color changes relative to 3.7. Analysis of variance was used to evaluate the effects of treatment, adhesive, and time on color change, and the level of significance was p < 0.05. Results: Ca(OH)₂ and 1 and 10 mg/mL DAP did not cause clinically perceivable tooth discoloration. Adhesive agent use significantly decreased tooth discoloration in the 1,000 mg/mL TAP group up to 4 weeks. However, adhesive use did not significantly improve coronal discoloration after thermocycling when 1,000 mg/mL TAP was used. Conclusions: Ca(OH)₂ and 1 and 10 mg/mL DAP showed no clinical discoloration. Using an adhesive significantly improved coronal discoloration up to 4 weeks with 1,000 mg/mL TAP.