• Journal of Surface Science and Engineering
• /
• v.54 no.5
• /
• pp.285-293
• /
• 2021

High-entropy TiAlCrSiN nano-composite coating was designed to improve mold life for high temperature liquid molding. Alloy design, powder fabrication and single alloying target fabrication for the high-entropy nano-composite coating were carried out. Using the single alloying target, an arc ion plating method was applied to prepare a TiAlCrSiN nano-composite coating had a 30 nm TiAlCrSiN layers are deposited layer by layer, and form about 4 ㎛-thickness of multi-layered coating. TiAlCrSiN nano-composite coating had a high hardness of about 39.9 GPa and a low coefficient of friction of less than about 0.47 in a dry environment. In addition, there was no change in the structure of the coating after the dissolution loss test in the molten metal at a temperature of about 1100 degrees.

• Journal of Surface Science and Engineering
• /
• v.54 no.3
• /
• pp.139-143
• /
• 2021

Cr-Al-N coatings were deposited onto WC-Co substrates using a cathodic arc evaporation (CAE) system. CAE technique is recognized to be a very useful process for hard coatings because it has many advantages such as high packing density and good adhesion to metallic substrates. In this study, the influence of deposition temperature as a key process parameter on film growth behavior and mechanical properties of Cr-Al-N coatings were systematically investigated and correlated with microstructural changes. From various analyses, the Cr-Al-N coatings prepared at deposition temperature of 450℃ in the CAE process showed excellent mechanical properties with higher deposition rate. The Cr-Al-N coatings with deposition temperature around 450℃ exhibited the highest hardness of about 35 GPa and elastic modulus of 442 GPa. The resistance to elastic strain to failure (H/E ratio) and the index of plastic deformation (H³/E² ratio) were also good values of 0.079 and 0.221 GPa, respectively, at the deposition temperature of 450℃. Based on the XRD, SEM and TEM analyses, the Cr-Al-N coatings exhibited a dense columnar structure with f.c.c. (Cr,Al)N multi-oriented phases in which crystallites showed irregular shapes (50~100nm in size) with many edge dislocations and lattice mismatches.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.04b
• /
• pp.89-90
• /
• 2009

Three kind of surface-leakage-test-patterns were fabricated and measured in order to investigate the surface leakage current of AlGaN/GaN heterostructures through etched GaN buffer surface and mesa wall. The pattern which contain the mesa wall has the largest surface leakage current among them. The leakage current due to the mesa wall is predominant source of the leakage current of AlGaN/GaN devices.

• Journal of the Korean Ceramic Society
• /
• v.36 no.2
• /
• pp.210-219
• /
• 1999

The fundamental dispersion property of Si2N4 and a combination of AlN and Nd2O3 as sintering additives in a variety of organic solvents such as alcohols, hydrocarbons, ketones, and ethers was investigated. The stabilization mechanism and interaction between organic functional groups of the various organic additives were studied to clarify the dispersibility of the ceramic particles in the nonaqueous suspending medium. characterization of the suspensions was based mainly on electrokinetic sonic amplitude(ESA) measurements and the flow curves obtained from the rheological studies as well as estimated Hamaker constants. It was found that the contribution of electrostatic repulsive forces to the Si3N4, AlN and Nd2O3 stabilization in organic media is appreciably greater than anticipated and is dependent on the physicochemical properties of organic solvents.

• Journal of the Korean Ceramic Society
• /
• v.50 no.4
• /
• pp.280-287
• /
• 2013

Plate-type phosphor is a promising substitute in overcoming the issues related to the powder phosphor paste mixed with resin. In this research, $Ca-{\alpha}-SiAlON:Eu^{2+}$ plate phosphor ($Ca_xSi_{12-(m+n)}Al_{m+n}O_nN_{16-n}:Eu_y$) was investigated for the varied compositions (m,n) of the host crystal with the fixed Eu content (y). Densification was promoted for the compositions with increasing 'm' values for the m=2n relationship. Dictated by the Eu concentration inside the phosphor crystal, photoluminescence intensity was stronger in ${\alpha}2$ specimen (m = 3.0, n = 1.5) containing the second phases when compared to ${\alpha}1$ specimen (m = 1.5, n = 0.75) comprising a single-phase ${\alpha}$-SiAlON. The concentration of Eu in the non-emitting amorphous interfacial glass phase was 2~4 times of the designed Eu concentration inside the ${\alpha}$-SiAlON crystal.

• Journal of the Korean Ceramic Society
• /
• v.28 no.8
• /
• pp.647-653
• /
• 1991

In order to synthesize fine AlN powder by the direct nitridation of Aluminum metal power added LiF and BaF2 as additives was heated at 150$0^{\circ}C$ for 3 hrs. in nitrogen gas with flow rate of 20 mι/sec. Additives are promoted the nitridation by prevented the aggromerate of powders when 3% LiF and 2% BaF2 were added to Al metal powder. Rate of nitridation was about 100% and average size of AlN powders were very fine such as 0.3 ${\mu}{\textrm}{m}$. Specific surface area of synthesized AlN powder was 3.95$m^2$/g and also O2 and N2 contents were 2.595% and 33.25%, respectively.

• Journal of the Korean Magnetics Society
• /
• v.4 no.4
• /
• pp.347-354
• /
• 1994

The structural change and magnetic properties of mechanically milled Fe-N and Mn-Al alloy powders have been investigated by XRD, TEM, VSM, $M\"{o}ssbauer$ spectroscopy and inelastic neutron scattering measurements. During milling of ${\gamma}'-Fe_{4}N$ powders, and fcc ${\gamma}'-Fe_{4}N$ phase is transformed to a bct ${\alpha}'-Fe(N)$ phase by stress-induced martensitic transformation, being accompanied by an initial increase in saturation magnetization. During annealing the bct ${\alpha}'-Fe(N)$ nanocrystalline phase which is obtained by mechanical grinding for a long time, an ${\alpha}'-Fe_{16}N_{2}$ phase partially appears as an intermediate phase at 673~773 K, causing an increase in saturation magnetization. During milling of Mn-45, 70 and 85 at.% Al mixed powders, Al atoms are partially solubilized into an ${\alpha}-Mn$ phase. The Al supersaturated ${\alpha}-Mn-type$ phases change from paramagnetic to ferromagnetic : the saturation magnetization is 11 emu/g for the as-milled Mn-70 at.% Al powders. Moreover, by removing almost all Al atoms from the as-milled Mn-85 at.% Al powders using chemical leaching, the saturation magnetization increases up to 36 emu/g. The above bct ${\alpha}'-Fe(N)$ and ferromagnetic ${\alpha}-Mn$ type alloys are the magnetic materials found for the first time, by using the present mechanochemical process.

• Journal of the Korean Ceramic Society
• /
• v.26 no.4
• /
• pp.453-458
• /
• 1989

Aluminum nitride powder prepared from the hydroxides, AlOOH and Al(OH)3 which were obtained by hydrolysis of Al-isopropoxide, was densified at 1750 and 180$0^{\circ}C$ for 60 min by hot-pressing under the pressure of 25kg/$\textrm{cm}^2$. Theoretical density could be obtained at 175$0^{\circ}C$. Their flexural strengths were 450MPa and 395MPa for the specimens obtained from Al(OH)3 and AlOOH, respectively. There was no remarkable change in flexural strength up to 100$0^{\circ}C$. Fracture toughness values were 3.50MN/m3/2 for Al(OH)3 and 3.11MN/m3/2 for AlOOH. It is assumed that these differences in mechanical properties are due to the abnormal grain growth for the AlN ceramics obtained from AlOOH.

• Journal of Powder Materials
• /
• v.26 no.5
• /
• pp.395-404
• /
• 2019

Aluminum nitride (AlN) has excellent electrical insulation property, high thermal conductivity, and a low thermal expansion coefficient; therefore, it is widely used as a heat sink, heat-conductive filler, and heat dissipation substrate. However, it is well known that the AlN-based materials have disadvantages such as low sinterability and poor mechanical properties. In this study, the effects of addition of various amounts (1-6 wt.%) of sintering additives $Y_2O_3$ and $Sm_2O_3$ on the thermal and mechanical properties of AlN samples pressureless sintered at $1850^{\circ}C$ in an $N_2$ atmosphere for a holding time of 2 h are examined. All AlN samples exhibit relative densities of more than 97%. It showed that the higher thermal conductivity as the $Y_2O_3$ content increased than the $Sm_2O_3$ additive, whereas all AlN samples exhibited higher mechanical properties as $Sm_2O_3$ content increased. The formation of secondary phases by reaction of $Y_2O_3$, $Sm_2O_3$ with oxygen from AlN lattice influenced the thermal and mechanical properties of AlN samples due to the reaction of the oxygen contents in AlN lattice.

• Journal of the Korean Ceramic Society
• /
• v.37 no.7
• /
• pp.645-650
• /
• 2000

Effects of the chemical composition and sintering atmosphere on the formation of reaction phases and physical properties of reactive hot-pressed TiB2-AlN-BN composites were investigated. At N2 atmosphere, TiN was formed by the reaction between Ti and N2, which inhibited the densification and results in inferior mechanical-and electrical properties of the composites. However, at Ar atmosphere, enhanced densification and physical properties of composites were obtained due to that the TiN formation reaction was excluded. Densification of the composites was also hindered by BN, therefore, inferior mechanical-and electrical properties of composites were obtained with amount of BN in the starting materials. At Ar atmosphere, TiB2-AlN-BN composites having 318 MPa of flexural strength, 3.5 MPa.m1/2 of fracture toughness and 276$\mu$Ω.cm of electrical resistivity were fabricated from mole ratio 1:2:1.6 of Ti-Al-BN mixtures.