• Journal of Powder Materials
• /
• v.21 no.5
• /
• pp.377-381
• /
• 2014

This work describes the coloration, chemical stability of $SiO_2$ and $SnO_2$-coated blue $CoAl_2O_4$ pigment. The $CoAl_2O_4$, raw materials, were synthesized by a co-precipitation method and coated with silica ($SiO_2$) and tin oxide ($SnO_2$) using sol-gel method, respectively. To study phase and coloration of $CoAl_2O_4$, we prepared nano sized $CoAl_2O_4$ pigments which were coated $SiO_2$ and $SnO_2$ using tetraethylorthosilicate, $Na_2SiO_3$ and $Na_2SiO_3$ as a coating material. To determine the stability of the coated samples and their colloidal solutions under acidic and basic conditions, colloidal nanoparticle solutions with various pH values were prepared and monitored over time. Blue $CoAl_2O_4$ solutions were tuned yellow color under all acidic/basic conditions. On the other hand, the chemical stability of $SiO_2$ and $SnO_2$-coated $CoAl_2O_4$ solution were improved when all samples pH values, respectively. Phase stability under acidic/basic condition of the core-shell type $CoAl_2O_4$ powders were characterized by transmission electron microscope, X-ray diffraction, CIE $L^*a^*b^*$ color parameter measurements.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.338-341
• /
• 1995

The surface properties after plasma etching of Al(Si, Cu) solutions using the chemistries of chlorinated and fluorinated gases with varying the etching time have been investigated using X-ray Photoelectron Spectroscopy. Impurities of C, Cl, F and O etc are observed on the etched Al(Si, Cu) films. After 95% etching, aluminum and silicon show metallic states and oxized (partially chlorinated) states, copper shows Cu metallic states and Cu-Clx(x$CuCl_x$ (x$CuCl_x$ (1

• Journal of Korea Foundry Society
• /
• v.14 no.5
• /
• pp.464-470
• /
• 1994

The horizontal continuous casting method with the heated mold was applied to study the solidification structures of the pure Al and Al-0.5wt%Si and Al-1.0wt%Si alloy rods. The results could be summarized as follows: 1. The S/L interface structures of pure Al represented the hexagonal cells at the casting speed of 590 and 350mm/min, respectively. However, the hexagonal cells became irregular as the casting speed and(or) Si amount increased. 2. The striation increased as the Si amount and casting speed increased and was found to result from the occurrence of growth twin crystals by XRD analysis. 3. The striation did not affect the mechanical and electrical property of the drawn wire from the casted rod. This means the striation is not a serious defect which has to consider in the production of micro-sized fine wire in the drawing process.

• Resources Recycling
• /
• v.32 no.1
• /
• pp.42-49
• /
• 2023

The glass ceramic secondary resource containing Li-Al-Si is used in inductor, fireproof glass, and transparent cookware and accounts for 14% of the total consumption of Li, which is the second most widely used after Li-ion batteries. Therefore, new Li resources should be explored when the demand for Li is exploding, and extensive research on Li recovery is needed. Herein, we recovered Li from fireproof Li-Al-Si glass ceramic, which is a new secondary resource containing Li. The fireproof glass among all Li-Al-Si glass ceramics was used as raw material that contained 1.5% Li, 9.4% Al, and 28.9% Si. The process for recovering Li from the fireproof glass was divided into two parts: (1) calcium salt roasting and (2) water leaching. In calcium salt roasting, a sample of fireproof glass was crushed and ground below 325 mesh. The leaching efficiency was compared based on the presence or absence of heat treatment of the fireproof glass. Moreover, the leaching rates based on the input ratios of calcium salt, Li-Al-Si glass, and ceramics and the leaching process based on calcium salt roasting temperatures were compared. In water leaching, the leaching and recovery rates of Li based on different temperatures, times, solid-liquid ratios, and number of continuous leaching stages were compared. The results revealed that fireproof glass ceramics containing Li-Al-Si should be heat treated to change phase to beta-type spodumene. CaCO₃ salt should be added at a ratio of 6:1 with glass ceramics containing Li-Al-Si, and then leached 4 times or more to achieve a recovery efficiency of Li over 98% from a solution containing 200 mg/L of Li.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.1
• /
• pp.53-57
• /
• 2010

The influence of CaO addition on the crystallization temperature, crystal types, and microstructure of L-A-S ($Li_2O-Al_2O_3-SiO_2$) glass-ceramics system fabricated from a coal bottom ash, produced at thermal power plant, was studied. The glass transition and crystallization temperatures were shifted to the higher temperature position with increasing CaO content in a non-isothermal analysis using a DTA. The major crystalline phases of L-A-S glass-ceramics system produced were identified as ${\beta}$-spodumene ($LiAlSi_2O_6$) and eucryptite ($LiAlSiO_4$). The glass-ceramics showed a bulk and surface crystallization behavior at a time. With increasing CaO content, the ${\beta}$-spodumene peak in XRD increased and some CaO-related phases were formed. The surface crystal grown from the exterior to the center in glass-ceramics showed various shapes by amount of CaO added. Some cracks were generated at the glass-ceramics containing CaO above 9 wt% due to the mismatch of thermal expansion coefficients between a ${\beta}$-spodumene and CaO-related crystal phases.

• Economic and Environmental Geology
• /
• v.5 no.2
• /
• pp.77-86
• /
• 1972

The system NaAlSiO_4-KAlSiO_4-SiO_2-H_2O, Bowen's "Petrogeny's Residua System" of course is extremely important in understanding the phase relationships of igneous and metamorphic rock in the continental crust. The phase relationships in this system, however, have not been completely established in the P-T range above the Mohorovicic discontinuity. They need to be established. In this study, the most probable sequence of P-T curves around a quaternary invariant point(~5Kb/${\sim}635^{\circ}C$) in the system using Schreinemakers' rule, is deduced, essentially on the basis of Morse's(1969a and b) experimental data. Possible modifications of the sequence of the P-T curves considering likely changes of the invariant chemogram are also considered. It is concluded that the sequence of P-T curves around the invariant point (~5Kb/${\sim}635^{\circ}C$) is (L), (Anl), (Or), (V), (Ne) and (Ab) on the P-T projection, where the P-T curve (L) is extended towards lower P-T regions, and the (Anl) curve is extended towards a region of higher temperature and lower pressure from the invariant point respectively.

• Korean Journal of Materials Research
• /
• v.3 no.3
• /
• pp.207-214
• /
• 1993

Glass-ceramic monoliths with an ultra-low thermal expansion coefficient have been synthesized by the sol-gel technique using metal alkoxides as starting materials and dimethyl formamide as a drying control chemical additive. The ternary gels: $Li_2O\cdot Al_2O_3\cdot 2, 4 or $6SiO_2$ were obtained by hydrolysis and polycondensation reactions of metal alkoxides of silicon, aluminum and lithium. To produce cylindrical crack-free gel monoliths, excess water was used to the starting solutions and drying rates were controlled precisely to prevent cracking. In conversion process ,${\beta}$-eucryptite, $Li_2O\cdot Al_2O_3\cdot 3SiO_2$ and P-spodumene with ,${\beta}$-quartz solid solution phase were obtained by heating at the range of 750 ~$1000^{\circ}C$. Above $800^{\circ}C$, the ,${\beta}$-spodumene phase increased while ,${\beta}$-eucryptite phase decreased. The thermal expansion coefficient of the crystallized specimens were -15~ $+5{\times}{10^{-7}}/{\circ}C$ over the temperature range from room temperature to $600^{\circ}C$.

• Journal of Sensor Science and Technology
• /
• v.7 no.5
• /
• pp.364-371
• /
• 1998

A novel antifuse has been developed for field programmable gate arrays (FPGA's) as a voltage programmable link with Al/$BaTiO_3/SiO_2$/TiW-silicide. The proper program voltage can be obtained by adjusting the deposition thickness of $BaTiO_3$ film. When a negative voltage was applied at bottom TiW-silicide electrode of the antifuse, based on $BaTiO_3(120{\AA})$/$SiO_2(120{\AA})$, the program voltage was about l4.4V and on-resistances were ranged between 40 and $50{\Omega}$. The current-voltage characteristics of antifuses are consistent with a Frenkel-Poole conduction model. However, there are some deviations depending on bias polarity that are probably due to the difference in the interface properties between Al/$BaTiO_3$ and TiW-silicide/$SiO_2$.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.2
• /
• pp.80-84
• /
• 2003

The mechanical and electrical properties of the hot-pressed and pressureless annealed SiC-Ti $B_2$electroconductive ceramic composites were investigated as functions of the liquid additives of $Al_2$ $O_3$+ $Y_2$ $O_3$. The result of phase analysis for the SiC-Ti $B_2$ composites by XRD revealed $\alpha$-SiC(6H), Ti $B_2$, and YAG(A $l_{5}$ $Y_3$ $O_{12}$ ) crystal phase. The relative density of SiC-Ti $B_2$ composites was increased with increased $Al_2$ $O_3$+ $Y_2$ $O_3$ contents. The fracture toughness showed the highest value of 6.04 Mpa $m^{\frac{1}{2}}$ for composites added with l2wt% A1$_2$ $O_3$+ $Y_2$ $O_3$ additives at room temperature. The electrical resistivity showed the lowest value of 6.2$\times$10$^{-3}$ $\Omega$ㆍcm for composite added with l6wt% $Al_2$ $O_3$+ $Y_2$ $O_3$ additives at room temperature. The electrical resistivity of the SiC-Ti $B_2$ composites was all positive temperature cofficient resistance(PTCR) in the temperature ranges from $25^{\circ}C$ to $700^{\circ}C$.

• Nuclear Engineering and Technology
• /
• v.45 no.7
• /
• pp.827-838
• /
• 2013

Interaction layer growth between U-Mo alloy fuel particles and Al in a dispersion fuel is a concern due to the volume expansion and other unfavorable irradiation behavior of the interaction product. To reduce interaction layer (IL) growth, a small amount of Si is added to the Al. As a result, IL growth is affected by the Si content in the Al matrix. In order to predict IL growth during fabrication and irradiation, empirical models were developed. For IL growth prediction during fabrication and any follow-on heating process before irradiation, out-of-pile heating test data were used to develop kinetic correlations. Two out-of-pile correlations, one for the pure Al matrix and the other for the Al matrix with Si addition, respectively, were developed, which are Arrhenius equations that include temperature and time. For IL growth predictions during irradiation, the out-of-pile correlations were modified to include a fission-rate term to consider fission enhanced diffusion, and multiplication factors to incorporate the Si addition effect and the effect of the Mo content. The in-pile correlation is applicable for a pure Al matrix and an Al matrix with the Si content up to 8 wt%, for fuel temperatures up to $200^{\circ}C$, and for Mo content in the range of 6 - 10wt%. In order to cover these ranges, in-pile data were included in modeling from various tests, such as the US RERTR-4, -5, -6, -7 and -9 tests and Korea's KOMO-4 test, that were designed to systematically examine the effects of the fission rate, temperature, Si content in Al matrix, and Mo content in U-Mo particles. A model converting the IL thickness to the IL volume fraction in the meat was also developed.