• 한국세라믹학회지
• /
• 제34권4호
• /
• pp.406-412
• /
• 1997

Al2O3/SiC hybrid-composite has been fabricated by the conventional powder process. The addition of $\alpha$-Al2O3 as seed particles in the transformation of ${\gamma}$-Al2O3 to $\alpha$-Al2O3 provided a homogeneity of the microstructure. The grain growth of Al2O3 are significantly surpressed by the addition of nano-size SiC particles. Dislocation were produced due to the difference of thermal expansion coefficient between Al2O3 and SiC and piled up on SiC particles in Al2O3 matrix, resulting in transgranular fracture. The high fracture strength of the composite was contributed to the grain refinement and the transgranular fracture mode. The addition of SiC platelets to Al2O3/SiC nano-composite decreased the fracture strength, but increased the fracture toughness. Coated SiC platelets with nitrides such as BN and Si3N4 enhanced fracture toughness much more than non-coated SiC platelets by enhancing crack deflection.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2014년도 추계학술대회 논문집
• /
• pp.304-304
• /
• 2014

Quaternary Ti-Al-Si-N films were deposited on WC-Co substrates by a hybrid deposition system of arc ion plating (AIP) method for Ti-Al source and DC magnetron sputtering technique for Si incorporation. The synthesized Ti-Al-Si-N films were revealed to be composites of solid-solution (Ti,Al)N crystallites and amorphous $Si_3N_4$ by instrumental analyses. The Si addition in Ti-Al-N films affected the refinement and uniform distribution of crystallites by percolation phenomenon of amorphous silicon nitride, similarly to Si effect in TiN film. As the Si content increased up to about 9 at.%, the hardness of Ti-Al-N film steeply increased from 30 GPa to about 50 GPa. The highest microhardness value (~50 GPa) was obtained from the Ti-Al-Si-N film having the Si content of 9 at.%, the microstructure of which was characterized by a nanocomposite of $nc-(Ti,Al)N/a-Si_3N_4$.

• 한국분말재료학회지
• /
• 제2권2호
• /
• pp.165-170
• /
• 1995

Alloying behavior of nanocrystalline Al-Ti-(Si) composite powders via mechanical alloying (MA) has been investigated, and the effect of Si on the microstructural changes during MA was discussed. The microstructures of both MA powders and extruded compacts were examined. In Al-Ti system, the solid solutionized nanocrystalline powders could be obtained by MA. On the contrary, fine Si particles were embedded as an elemental state in the matrix of Al-Ti-Si system because of the brittleness and the negligible solid solubility of Si in Al. After hot extrusion, $Al3Ti$ phase was finely precipitated in Al-10fSTi alloy, and Si particles were dissolved to form $(Al, Si)_3Ti$ phase in Al-10%Ti-2%Si alloy.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1996년도 특별강연 및 추계학술발표 개요집
• /
• pp.173-175
• /
• 1996

• 한국재료학회지
• /
• 제12권1호
• /
• pp.48-53
• /
• 2002

$Al_2O_3-SiC$ and $Al_2O_3-SiC$-TiC composite powders were prepared by SHS process using $SiO_2,\;TiO_2$, Al and C as raw materials. Aluminum powder was used as reducing agent of $SiO_2,\;TiO_2$ and activated charcoal was used as carbon source. In the preparations of $Al_2O_3-SiC$, the effect of the molar ratio in raw materials, compaction pressure, preheating temperature and atmosphere were investigated. The most important variable affecting the synthesis of $Al_2O_3-SiC$ was the molar ratio of carbon. Unreactants remained in the product among all conditions without compaction. The optimum condition in this reaction was $SiO_2$: Al: C=3: 5: 5.5, 80MPa compaction pressure under Preheating of $400^{\circ}C$ with Ar atmosphere. However there remains cabon in the optimum condition. The effect of $TiO_2$ as additive was investigated in the preparations of $Al_2O_3-SiC$. As a result of $TiO_2$ addition, $Al_2O_3-SiC$-TiC composite powder was prepared. The $Al_2O_3$ powder showed an angular type with 8 to $15{\mu}m$, and the particle size of SiC powder were 5~$10{\mu}m$ and TiC powder were 2 to $5{\mu}m$.

• 자원리싸이클링
• /
• 제7권5호
• /
• pp.52-57
• /
• 1998

현재 구조용 합금으로는 최경량화인 Mg-Li-Al합금의 내식성에 미치는 Si의 영향을 전기화학적 분극시험에 의하여 조사하였다. 전기화학적 분극시험은 ${KH}_{2}{PO}_{5}$·NaOH 완충용액으로 pH7로 고정한 0.03% NaCl 전해액에서 Mg-Li-Al(A4)합금과 Mg-Li-Al에 Si을 0.48 wt% 첨가한 (S5)합금에 대하여 전류밀도에 따른 전위의 변화를 측정하였다. 실험 결과 미량의 Si를 첨가한 Mg-Li-Al-Si 합금의 경우가 Si을 첨가하지 않은 Mg-Li-Al 합금의 경우보다 부식속도가 증가하였으며, 부식생성물의 분포범위도 넓었고 생성량도 많았다. 이러한 실험결과를 고려해 볼 때, Mg-Li-Al 합금에 미량이지만 Sidl 첨가됨으로써 Mg-Li-Al 합금의 내식성이 감소된다고 판단된다. 따라서 강도특성이 향상을 목적으로 첨가하는 Si의 첨가량에 대해서는 적절한 양의 조정이 필요하다.

• 한국주조공학회지
• /
• 제17권2호
• /
• pp.180-187
• /
• 1997

The influence of solidification condition on the segregation of SiC particles in the $Al-xSi/6wt%SiC_p$(x: 6, 10, 14, 18${\cdot}$wt%) composites was investigated in the study. The results are as follows: 1) During the counter-gravity unidirectional solidification of $Al-Si/SiC_p$ composites melt, most of the SiC particles are pushed to the top of the casting. 2) The SiC particles pushing in the $Al-Si/SiC_p$ composite melts are not observed, when the interface velocity of melts increases more than 1.41 ${\mu}m/sec$. 3) The SiC particles are entrapped in the interdendrite regions, when the sizes of SiC particles in the $Al-Si/SiC_p$ composites are large than ${\varphi}22{\mu}m$.

• 마이크로전자및패키징학회지
• /
• 제7권2호
• /
• pp.37-42
• /
• 2000

저유전상수 폴리머와 $SiO_2$위에 형성된 Al/Ti박막의 우선방위에 대해 비교하였다. DC 마그네트론 스퍼터를 이용하여 50 nm 두께의 Ti과 500 nm의 Al-1%Si-0.5%Cu(wt%) 합금 박막을 저유전상수 폴리머와 $SiO_2$기판위에 증착하였다. Al의 우선방위는 XRD $\theta$-2$\theta$와 rocking curve로 측정하였고, Al/Ti박막의 미세조직은 투과전자현미경 (TEM)으로 관찰하였다. 저 유전상수 폴리머 위에 증착된 Al/Ti박막은 $SiO_2$위에 증착된 것보다 낮은 우선방위를 가졌다. 단면 TEM으로 Ti을 관찰한 결과, $SiO_2$위의 Ti의 결정립은 기판에 수직하게 성장하였으나 저유전상수 폴리머 위의 Ti 결정립은 등축정으로 성장하였으며, 저유전상수 폴리머위의 Al/Ti박막이 낮은 우선방위를 갖는 이유는 Ti 미세조직 때문이었다.

• 한국세라믹학회지
• /
• 제33권11호
• /
• pp.1209-1216
• /
• 1996

MoSi2-Al2O3 composites were prepared by thermal explosion mode of self-propagating high temperature syn-thesis (SHS) using element powders of MoO3 Mo Si and Al. The combustion products of MoSi2 which have 10, 20, 30 and 40 wt% Al2O3 showed the molten state in the range of Mo to MoO3 6:1-9.5:1, 2:1-8:1, 1:1-5:1, and 1:1-3:1 (molar ratio) respectively. The combustion products which made least seperation the molten phase from the slag phase were in Mo/MoO3=9, 5:1, 8:1, 5:1 and 3:1 (molar ratio) respectively. Particles size of MoSi2 and Al2O3 in the combustion product were decreased as the molar ratio of Mo to MoO3 increase. By XRD analysis only MoSi2 and $\alpha$-Al2O3 peaks were identified in the combusion products, In case of MoSi2 containing 20wt% Al2O3 5.1wt% Al existed into MoSi2 grains and 30.7wt% Si and 7.7wt% Mo existed into Al2O3 grains. The relative density of MoSi2 containing 10, 20, 30 and 40 wt% Al2O3 were 82.7, 85.2, and 81.9% respectively. The fracture strength of MoSi2-Al2O3 composites increased with increasing Al2O3 and that of MoSi2-20wt% Al2O3 composite was 195 MPa.

• 한국주조공학회지
• /
• 제33권6호
• /
• pp.233-241
• /
• 2013

Effect of Fe and Mn contents on the castability of Al-9wt%Si-xMg-yFe-zMn alloy has been studied. The alloy was composed of ${\alpha}$-Al phase, Al+eutectic Si phase, ${\beta}$-Al5FeSi compound and chinese script ${\alpha}$-$Al_{15}(Mn,Fe)_3Si_2$ compound. ${\beta}$-$Al_5FeSi$ and ${\alpha}$-$Al_{15}(Mn,Fe)_3Si_2$ compounds assumed to effect the fluidity and shrinkage behaviors of the alloy during solidification due to the crystallization of ${\alpha}$-$Al_{15}(Fe,Mn)_3Si_2$ and ${\beta}$-$Al_5FeSi$ compounds above eutectic temperature. As Fe and Mn contents of Al-9wt%Si-0.3wt%Mg system alloy increased from 0.15wt% to 0.6wt% and from 0.3wt% to 0.7wt%, fluidity of the alloy decreased by 5.7% and 3.3%, respectively. And as Mg content of Al-9wt%Si-0.45wt%Fe-0.5wt%Mn system alloy increased from 0.3wt% to 0.4wt%, fluidity of the alloy decreased by 8.6%. When Fe content of the alloy increased from 0.15wt% to 0.6wt%, macro shrinkage ratio decreased from 6.1% to 4.1%, and micro shrinkage ratio increased from 0.04% to 0.24%. Similarly, Mn content of the alloy increased from 0.3wt% to 0.7wt%, macro shrinkage ratio decreased from 6.0% to 4.5% and micro shrinkage ratio increased from 0.12% to 0.18%. Judging from the castability of the alloy, Al-9wt%Si-0.3wt%Mg alloy with low content of Fe and Mn, 0.1wt% Fe and 0.3wt% Mn, is recommendable.