• Journal of Powder Materials
• /
• v.24 no.6
• /
• pp.431-436
• /
• 2017

SiAlON-based ceramics are some of the most typical oxynitride ceramic materials, which can be used as cutting tools for heat-resistant super-alloys (HRSA). SiAlON can be fabricated by using gas-pressure reactive sintering from the raw materials, nitrides and oxides such as $Si_3N_4$, AlN, $Al_2O_3$, and $Yb_2O_3$. In this study, we fabricate $Yb_{m/3}Si_{12-(m+n)}Al_{m+n}O_nN_{16-n}$ (m=0.3, n=1.9, 2.3, 2.7) ceramics by using gas-pressure sintering at different sintering temperatures. Then, the densification behavior, phase formation, microstructure, and hardness of the sintered specimens are characterized. We obtain a fully densified specimen with ${\beta}$-SiAlON after gas-pressure sintering at $1820^{\circ}C$ for 90 min. under 10 atm $N_2$ pressure. These SiAlON ceramic materials exhibited hardness values of ~92.9 HRA. The potential of these SiAlON ceramics for cutting tool application is also discussed.

• Corrosion Science and Technology
• /
• v.7 no.6
• /
• pp.315-318
• /
• 2008

The atmospheric corrosion performance of Al-alloying, Si-alloying and Al-Si-alloying steel were studied by wet/dry cyclic corrosion tests (CCT) at $30^{\circ}C$ and 60% relative humidity (RH). The corrosion electrolyte used for CCT was 0.052 wt% $NaHSO_{3}$ (pH~4) solution. The result of gravimetry demonstrated that Al-Si-bearing steels showed lower corrosion resistance than other rusted steels. But the rusted 0.7%Si-alloying steel showed a better corrosion resistance than rusted mild steel. Polarization curves demonstrated that Al-/Si-alloying and Al-Si-alloying improved the rest potential of steel at the initial stage; and accelerated the cathodic reduction and anodic dissolution after a rust layer formed on the surfaces of steels. XRD results showed that Al-Si-alloying decreased the volume fraction of $Fe_{3}O_{4}$ and $\alpha-FeOOH$. The recycle of acid accelerated the corrosion of steel at the initial stage. After the rust layer formed on the steel, the leak of rust destabilized the rust layer due to the dissolution of compound containing Al (such as $FeAl_{2}O_{4}$, $(Fe,\;Si)_{2}(Fe,\;Al)O_{4}$). Al-Si-alloying is hence not suitable for improving the anti-corrosion resistance of steel in industrial atmosphere.

• Korean Journal of Materials Research
• /
• v.26 no.11
• /
• pp.628-634
• /
• 2016

The cold rolling workability and mechanical properties of two new alloys, designed and cast Al-5.5Mg-2.9Si and Al-7Mg-0.9Zn alloys, were investigated in detail. The two alloy sheets of 4 mm thickness, 30 mm width and 100 mm length were reduced to a thickness of 1 mm by multi-pass rolling at ambient temperature. The rolling workability was better for the Al-7Mg-0.9Zn alloy than for the Al-5.5Mg-2.9Si alloy; in case of the former alloy, edge cracks began to occur at 50% rolling reduction, and their number and length increased with rolling reduction; however, in the latter alloy, the sheets did not have any cracks even at higher rolling reduction. The mechanical properties of tensile strength and elongation were also better in the Al-7Mg-0.9Zn alloy than in Al-5.5Mg-2.9Si alloy. Work hardening ability after cold rolling was also higher in the Al-7Mg-0.9Zn alloy than in the Al-5.5Mg-2.9Si alloy. At the same time, the texture development was very similar for both alloys; typical rolling texture developed in both alloys. These differences in the two alloys can primarily be explained by the existence of precipitates of $Mg_2Si$. It is concluded that the Al-7Mg-0.9Zn alloy is better than the Al-5.5Mg-2.9Si alloy in terms of mechanical properties.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.11
• /
• pp.968-972
• /
• 2008

Ni/Ti/Al multilayer system ('/'denotes the deposition sequence) was tested for low-resistance ohmic contact formation to Al-implanted p-type 4H-SiC. Ni 30 nm / Ti 50 nm / Al 300 nm layers were sequentially deposited by e-beam evaporation on the 4H-SiC samples which were implanted with Al (norminal doping concentration = $4\times10^{19}cm^{-3}$) and then annealed at $1700^{\circ}C$ for dopant activation. Rapid thermal anneal (RTA) temperature for ohmic contact formation was varied in the range of $840\sim930^{\circ}C$. Specific contact resistances were extracted from the measured current vs. voltage (I-V) data of linear- and circular transfer length method (TLM) patterns. In constrast to Ni contact, Ni/Ti/Al contact shows perfectly linear I-V characteristics, and possesses much lower contact resistance of about $2\sim3\times10^{-4}\Omega{\cdot}cm^2$ even after low-temperature RTA at $840^{\circ}C$, which is about 2 orders of magnitude smaller than that of Ni contact. Therefore, it was shown that RTA temperature for ohmic contact formation can be lowered to at least $840^{\circ}C$ without significant compromise of contact resistance. X-ray diffraction (XRD) analysis indicated the existence of intermetallic compounds of Ni and Al as well as $NiSi_{1-x}$, but characteristic peaks of $Ti_{3}SiC_2$, a probable narrow-gap interfacial alloy responsible for low-resistance Ti/Al ohmic contact formation, were not detected. Therefore, Al in-diffusion into SiC surface region is considered to be the dominant mechanism of improvement in conduction behavior of Ni/Ti/Al contact.

• Journal of Korea Foundry Society
• /
• v.10 no.1
• /
• pp.43-49
• /
• 1990

The influences of Cu and Mg addition on wear properties of SiC particulate reinforced Al-Si metal(alloy) matrix composites were investigated. Metal matrix composites were prepared by combination of compocasting and hot pressing techniques. The main results obtained are as follows : 1) The composite with Mg addition exhibits letter wear resistance than that with Cu addition. It is considered that Mg addition improved wettability of matal matrix composite by the strong segregation to the SiC / Al matrix interface. 2) After homogenization treatment, it was found that the interfacial segregation of Mg was predominant, while that of Cu was not detected. 3) The SiC / Al-11Si eutectic composite exhibits better wear resistance than the SiC / Al-6Si hypoeutectic composite does. 4) It seems that the increase in the amount of Mg addition affects on the uniform dispersion of SiC particulates, on the refinement of microstructure and on age hardening and these effects cause wear resistance improvement of composites.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.275.2-275.2
• /
• 2014

현재 자동차 분야에서 차량 경량화의 한 수단으로 자동차용 유리를 고강도 투명 플라스틱 소재인 Polycarbonate(PC)로 대체하고자 하는 연구가 이루어지고 있다. 하지만, PC의 낮은 내마모 특성과 자외선에 의한 열화 및 변색 현상은 해결하여야 할 문제점으로 지적되고 있으며, 에너지 소비 저감을 위하여 적외선 영역 반사율(reflectance)이 높은 저방사(low emissivity) 특성이 요구되고 있다. 본 연구에서는, ICP-assisted reactive magnetron sputtering 장비를 이용하여 투과율(transmittance)이 확보되고, 고경도 특성을 갖는 Al-Si-N와 300 nm 파장 이하의 자외선 차단 특성이 있는 SiN:H 그리고 저방사 특성을 위해 Al을 증착하였고, 박막의 증착 순서는 SiN:H 박막을 가장 아래에 증착하고 그 위에 Al/Al-Si-N 박막을 다층으로 형성하였다. 박막의 chemical state와 crystallinity를 확인하기 위하여 XPS(X-ray Photoelectron Spectroscopy), XRD (X-ray Diffraction)를 이용하여 분석하였다. Knoop ${\mu}$-hardness tester와 Taber tester를 이용하여 경도 및 내마모 특성을 분석하였다. 제작된 샘플의 Al-Si-N 박막 경도는 Si 비율에 따라 다른 경도 특성을 갖는데, 실제 Si/(Al+Si) 비율이 24%에서 최대 31 GPa의 경도 값을 갖는 것을 확인하였다. UV-Vis Spectrometer를 이용하여 250 nm~700 nm 파장의 투과율을 측정하였고, 자외선 영역의 경우 SiN:H 박막에 의해 300 nm 이하의 파장에서 2% 이하의 투과율을 확인하였다. 그리고 FT-IR(Fourier Transform Infrared Spectroscopy)를 이용하여 $2.5{\mu}m{\sim}15{\mu}m$ 파장의 반사율을 이용하여 방사율을 측정하였는데, 3*(Al/Al-Si-N) 구조의 다층 박막의 경우 방사율은 0.27로 측정되었다.

• Journal of the Korean Chemical Society
• /
• v.55 no.4
• /
• pp.570-574
• /
• 2011

Large colorless single crystals of analcime with diameters up to 0.20 mm have been synthesized from gels with the composition of $3.00SiO_2$ : $1.50NaAlO_2$ : 8.02NaOH : $454H_2O$ : 5.00TEA. The fully $Na^+$-exchanged analcime have been prepared with aqueous 0.1 M NaCl (pH adjusted from 6 to 11 by dropwise addition of NaOH). The single-crystal structure of hydrated $|Na_{0.94}(H_2O)|[Si_{2.06}Al_{0.94}O_6]$-ANA per unit cell, a=13.703(3) ${\AA}$, has been determined by single-crystal X-ray diffraction technique in the orthorhombic space group Ibca at 294 K. The structure was refined using all intenties to the final error indices (using only the 1,446 reflections for which $F_o$ > $4{\sigma}(F_o))R_1/wR_2$ = 0.054/0.143. About 15 $Na^+$ ions are located at three nonequivalent positions and octahedrally coordinated. The chemical composition is $Na_{0.94}(H_2O)Si_{2.06}Al_{0.94}O_6$. The Si/Al ratio of synthetic analcime is 2.19 determined by the occupations of cations, 14.79, in the single-crystal determination work.

• Journal of the Korean Ceramic Society
• /
• v.34 no.1
• /
• pp.1-6
• /
• 1997

In home-style microwave oven, silica-Al powder mixture was ignited among pellets and combustion wave-front propagated to produce Si+AIN+Al2O3 as resultant phases under N2 atmosphere. Without cooling pro-cedure the resultant phases of Si+AIN+Al2O3 continously absorbed microwave and were heated to be syn-thesized into sialon phases. This synthesis rate of sialon phases from silica-Al powder mixture in home-style microwave oven was higher than that in conventional furnace, and total processing time was around 1 hour, which could save energy and cost.

• Journal of the Korean Ceramic Society
• /
• v.37 no.12
• /
• pp.1198-1203
• /
• 2000

AlN와 Si을 이용하여 체적 탄성파 over-moded 공진기를 형성하였다. 높은 c-축 배향성을 갖는 AlN 압전박막은 sputtering에 의해 저온에서 증착하였다. AlN 박막의 c-축 배향성은 기판과 타겥의 거리가 가까울수록, 증착 압력이 낮을수록 (002) 면으로의 성장이 촉진되었다. Si 기판을 이용한 over-moded 공진기로부터 TFR의 임피던스를 산출한 결과 공진영역의 면적에 가장 의존하였다. Al/AlN/Al로 이루어진 TFR의 입력 임피던스는 공진 영역이 크기가 200㎛×200㎛인 경우 가장 50Ω에 근접하였다. Over-moded 공진 특성은 Si 기판의 낮은 Q로 인해 mode 수 294인 2.60976 GHz에서 0.109%의 유효 전기기계결합계수(K/sub eff/²)와 0.3의 K/sub eff/²·Q값을 보였다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.1
• /
• pp.122-131
• /
• 1995

The research trends for metal matrix composites have been on basic mechanical properties, fatigue behavior after aging and fractographic observations. In this study, the fatigue crack initiation as well as the fatigue crack growth behavior and the fracture mechanism were investigated through observations of the fracture surface on silicon carbide particles reinforced aluminum metal matrix composites(SiCp/Al). Based on the fractographic study done by scanning electron microscope and replica, crack growth path model and fracture mechanism are presented. The mechanical properties, such as the tensile strength, yield strength and elongation of SiCp/Al composites are improved in a longitudinal direction, however, the fatigue life is shorter than the basic Al6061 alloys. From fractographic observations, it is found that the failure mode is ductile in basic Ai6061 alloys. And because some SiC particles were pulled out from the matrix and a few SiC particles could be seen on the fracture surface of SiCp/Al, crack growth paths are believed to follow the interface of the matrix and its particles.