• 한국재료학회지
• /
• 제24권1호
• /
• pp.53-59
• /
• 2014

The corrosion resistance of submerged entry nozzle (SEN) materials were investigated for high-class steel manufacturing. Composite samples were fabricated by mixing $ZrO_2$, $Al_2O_3$, MgO, mullite, spinel, and carbon. The raw materials were mixed with attrition milling, compacted in a uniaxial pressure of 200MPa and calcined at $1000^{\circ}C$ for 3 h in $N_2$ atmosphere. The bulk density and apparent porosity of the calcined samples were measured by the liquid displacement method in water using Archimedes's principle. The corrosion resistance of the samples were measured by cup test with mold powder at $1550^{\circ}C$ for 2 h. The microstructure and elemental analysis of samples were observed by scanning electron microscopy (SEM), energy dispersive spectrum (EDS), and X-ray diffraction pattern (XRD). The XRD result shows that the starting raw materials were crystalline phase. The microstructure of fabricated specimen was investigated before and after corrosion tests at $1000^{\circ}C$ and $1550^{\circ}C$ for 2h. $ZrO_2$-C composite showed good resistance in the slag corrosion test. Among the composite oxide materials, $ZrO_2-Al_2O_3$-C and $ZrO_2$-MgO-C showed better resistance than $ZrO_2$-C in the slag corrosion test. The diameter variation index of $ZrO_2$-C refractory was 16.1 at $1000^{\circ}C$ for 2 h. The diameter variation index of the $ZrO_2-Al_2O_3$-C refractory was larger than that of the $ZrO_2$-C refractory at $1550^{\circ}C$ for 2 h.

• Bulletin of the Korean Chemical Society
• /
• 제29권9호
• /
• pp.1699-1704
• /
• 2008

• 한국세라믹학회지
• /
• 제31권11호
• /
• pp.1259-1264
• /
• 1994

$\beta$-Sialon has been regarded as one of promising materials showing high strength, fracture toughness, corrosion resistence and wear resistence. The improvement of the fracture toughness and tribological properties of $\beta$-Sialon (Z=1) has been attempeted by fabricating the $\beta$-Sialon/ SiC whisker composite. Each of green body composed of following ingredients, i.e., Si3N4, AlN, Y2O3 nd SiC, respectively, was first fired at 178$0^{\circ}C$ for 3hrs in N2 atmosphere and then post-HIPed at 173$0^{\circ}C$ for 1 hr under 170 MPa for N2 gas pressure. The fracture toughness, flexural strength and tribological properties increased with increasing SiC whisker content, despite the reduction of the relative density and hardness. $\beta$-Sialon/15 vol% SiC whisker showed a significant enhancement of wear resistance compared to the monolithic $\beta$-Sialon. The addition of SiC whisker caused the reduction of the density and hardness, but induced the increment of wear resistance.

• 한국세라믹학회지
• /
• 제40권9호
• /
• pp.874-880
• /
• 2003

AIN-BN계 머시너블 세라믹의 미세조직, 기계적 성질 및 기계 가공성에 미치는 h-BN 첨가의 영향을 조사하였다. 소결체의 상대밀도는 h-BN 첨가량의 증가와 더불어 감소하였다. 또한, 4점 굽힘 강도도 AIN 단미의 238 MPa에서 30 vo1% BN 첨가에 의해 182 MPa까지 감소하였다. 낮은 탄성계수와 AIN 매트릭스와 h-BN 입자와의 열팽창계수의 차이에 의해 발생한 잔류인장응력에 의해 AIN-BN 복합재료의 강도가 감소되었다고 생각된다. 판상형태의 h-BN 입자에 의해 균열편향과 pull-out은 증가하였으나, 파괴인성은 BN 첨가량과 더불어 감소하였다. AIN 분말표면에 존재하는 알루미나와 소결조제인 $Y_2$O$_3$와의 반응에 의해 2차상인 YAG상과 ${\gamma}$-Al$_2$O$_3$상이 생성되었다. AIN에 10～30 vo1%의 BN을 첨가한 복합재료에 대하여 수행한 절삭시험에서 절삭력과 배분력은 h-BN 첨가량에 따라 감소하였으며, 우수한 기계 가공성을 입증하였다. 또한, 모든 시편에서 짧은 시간 내에 0.5 $\mu$m (Ra) 이하의 비교적 양호한 표면 거칠기에 도달할 수 있었다.

• 멤브레인
• /
• 제32권2호
• /
• pp.116-125
• /
• 2022

본 실험에서는 α-Al₂O₃ 세라믹 중공사를 지지체로 사용하였고, 무전해 도금을 통해 Pd 및 Pd-Ag가 도금된 수소 분리막을 제조하였다. Pd-Ag 분리막은 Pd와 Ag 합금 형태로 만들기 위하여 500℃, 10 h 동안의 annealing 과정을 거쳤으며, EDS (Energy Dispersive X-ray Spectroscopy) 분석을 통해 Pd-Ag 합금이 되었다는 것을 확인하였다. 또한, SEM (Scanning Electron Microscope) 분석을 통해 제조된 Pd 및 Pd-Ag 도금층의 두께는 약 8.98, 9.29 ㎛으로 측정되었다. 제조된 수소 분리막은 350~450℃, 1-4 bar의 범위에서 수소 단일 가스, 혼합가스(H₂, N₂)를 이용하여 수소 투과 실험을 진행하였다. 수소 단일 가스에서 Pd와 Pd-Ag 분리막은 최대 각각 21.85, 13.76 mL/cm²·min의 flux를 가지며, 혼합가스에서는 450℃, 4 bar의 조건일 때, 1216, 361의 separation factor가 각각 나오는 것을 확인하였다.

• 한국세라믹학회지
• /
• 제55권6호
• /
• pp.556-561
• /
• 2018

In this study, we performed a microwave sintering (MWS) of $Al_2O_3$ ceramic and $Al_2O_3$-based composites with nominal contents of graphene nanoplatelets (GPLs) of 0.2, 0.4, 0.6, and 0.8 vol%. The GPL dispersion in N-methyl pyrroleketone was optimized to deagglomerate the GPLs without damaging their structure. Dense composites were then obtained by MWS at $1500^{\circ}C$ for 30 min. The effects of different GPL contents on the phase compositions, microstructures, and mechanical properties of the composites were investigated. The microstructures of the composites became finer with the incorporation of the GPLs. The well-dispersed GPL fillers led to higher sintered densities in the composites. The optimal mechanical properties were achieved with 0.4 vol% GPLs. For this sample, the hardness, fracture toughness, and bending strength were $2000kgf/mm^2$, $6.19MPa{\cdot}m^{1/2}$, and 365.10 MPa, respectively. The addition of GPL could improve the microstructure of the $Al_2O_3$ ceramic and has potential to improve the fracture toughness of the ceramics.

• Steel and Composite Structures
• /
• 제21권3호
• /
• pp.573-588
• /
• 2016

Carbon Fiber Reinforced Plastic (CFRP) and Titanium Alloy (Ti6Al4V) stack, extensively used in aerospace structural components are assembled by fasteners and the holes are made using drilling process. Drilling of stack in one shot is a complicated process due to dissimilarity in the material properties. It is vital to have optimal machining condition and tool geometry for better hole quality and tool life. In this study the tool wear and hole quality were analysed by experimental analysis using three modified twist drills and online tool condition monitoring using Acoustics Emission (AE) sensor. Helix angle and point angle influence tool performance and cutting force. It was found that a tool geometry (TG1) with high helix angle of $35^{\circ}$ with low point angle $130^{\circ}$ results in reduction in thrust force of 150-500 N range but the TG2 also perform almost similar to TG1, but when compared with the AErms voltage generated during drilling it was found that progressive rise in voltage in TG1 is less with respect to TG2 which can be attributed to tool life. In process wear monitoring was done using crest factor as monitoring index. AErms voltage were measured and correlated with the performance of the drills.

• Bulletin of the Korean Chemical Society
• /
• 제34권5호
• /
• pp.1345-1348
• /
• 2013

We investigated the tribochemical and wear properties of Polytetrafluoroethylene (PTFE) based polymer matrix composites with nanoceramic (NC) ${\beta}$-sialon, and $Al_2O_3$ particles for the mechanical seal applications at low temperature. SEM showed that NC particles were homogeneously distributed in the polymer matrix and initiated the formation of the supramolecular spherulites around NC. From the temperature stimulated depolarization (TSD) current results, it was analyzed that the surface charge on nanoceramic affected the formation of the spherulites structure. 2 wt % $Al_2O_3$ NC did not degrade the mechanical properties of PTFE so that composites showed the similar values of tensile strength, elongation at the rupture and friction coefficient as those of neat PTFE. However, the composite with 2 wt % $Al_2O_3$ NC revealed the improved wear resistance, wear rate of 0.4-1.2 mg/h at room temperature and 0.28 mg/h at $-40^{\circ}C$, respectively, while the neat PTFE the 70-75 mg/h at room temperature and 70.3 mg/h at $-40^{\circ}C$.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2004년도 SMICS 2004 International Symposium on Maritime and Communication Sciences
• /
• pp.70-73
• /
• 2004

The packaging of the integrated circuits requires knowledge of ceramics and metals to accommodate the fabrication of modules that are used to construct subsystems and entire systems from extremely small components. Composite ceramics (Al$_2$O$_3$-SiO$_2$) were tested for substrates. A stress analysis was conducted for a linear work-hardening metal cylinder embedded in an infinite ceramic matrix. The bond between the metal and ceramic was established at high temperature and stresses developed during cooling to room temperature. The calculations showed that the stresses depend on the mismatch in thermal expansion, the elastic properties, and the yield strength and work hardening rate of the metal. Experimental measurements of the surface stresses have also been made on a Cu/Al$_2$O$_3$-SiO$_2$ceramic system, using an indentation technique. A comparison revealed that the calculated stresses were appreciably larger than the measured surface stresses, indicating an important difference between the bulk and surface residual stresses. However, it was also shown that porosity in the metal could plastically expand and permit substantial dilatational relaxation of the residual stresses. Conversely it was noted that pore clusters were capable of initiating ductile rupture, by means of a plastic instability, in the presence of appreciable tri-axiality. The role of ceramics for packaging of microelectronics will continue to be extremely challenging.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.308-312
• /
• 2003

The packaging of the integrated circuits requires knowledge of ceramics and metals to accommodate the fabrication of modules that are used to construct subsystems and entire systems from extremely small components. Composite ceramics ($Al_2O_3-SiO_2$) were tested for substrates. A stress analysis was conducted for a linear work-hardening metal cylinder embedded in an infinite ceramic matrix. The bond between the metal and ceramic was established at high temperature and stresses developed during cooling to room temperature. The calculations showed that the stresses depend on the mismatch in thermal expansion, the elastic properties, and the yield strength and work hardening rate of the metal. Experimental measurements of the surface stresses have also been made on a $Cu/Al_2O_3-SiO_2$ ceramic system, using an indentation technique. A comparison revealed that the calculated stresses were appreciably larger than the measured surface stresses, indicating an important difference between the bulk and surface residual stresses. However, it was also shown that porosity in the metal could plastically expand and permit substantial dilatational relaxation of the residual stresses. Conversely it was noted that pore clusters were capable of initiating ductile rupture, by means of a plastic instability, in the presence of appreciable tri-axiality. The role of ceramics for packaging of microelectronics will continue to be extremely challenging.