• 한국표면공학회지
• /
• 제25권5호
• /
• pp.223-233
• /
• 1992

(Ti, Al)N films were deposited on 304 stainless steel by D.C. magnetron sputtering using Al target and Ti plate. The properties of (Ti, Al)N films such as composition, microhardness, grain size, crystal structure were investigated. The chemical composition of (Ti, Al)N films was similar to the sputter area ratio of titanium to aluminum target by means of EDS and AES survey. The higher bias voltage to substrate and the smaller input of N2 gas showedthe increased microhardness and the finer grain size of the films. The results obtained from this study show, it is belived, that the (Ti, Al)N film by D.C.magne-tron sputtering is promising in the wear resistance use.

• Radiation Oncology Journal
• /
• 제15권2호
• /
• pp.159-165
• /
• 1997

목적 : 광자선과 블록을 얻는 트레이와의 상호작용에 의해 생성된 2차 전자는 피하층에 과도 한 선량증가의 원인이 된다. 이런 전자오염으로 인한 표면선량을 감소시키기 위해 트레이 아래 전자필터를 부착하는 것이 유용하다. 대상 및 방법 :두께가 다른 Cu판, Al판 그리고 Cu/Al 복합판을 사용하여 전자오염에 의한 표면선량을 감소시키는 효과를 측정하였다. 최적의 필터를 찾기 위해서 $10m\times10cm$ 조사야와 SSD 78.5cm의 기하학적 모형으로 표면에서부터 최대선량 지점까지 2mm 간격으로 흡수선량을 측정하였다. 최적필터의 조사야 의존성을 구하기 위해서 $4cm\times4cm$에서부터 $25cm\times25cm$까지 조사면적을 변화시켜가며 흡수선량을 측정하였다 결과 : 표면선량은 조사면적을 증가시키면 서서히 증가하였고 $15cm\times15cm$ 조사면적 이상에 서는 표면선량이 급속히 증가하였다. Al판을 사용했을 경우 표면선량이 최대선량 지점의 선량보다 낮게 유지되지 않으므로 Al판은 전자필터로는 부적합하였으며 0.5mm Cu판과 Cu/Al=0.28mm/1.5mm 복합판이 최적 전자필터로 결정되었다. 두가지 최적필터의 경우 $4cm\times4cm$ 조사면에서는 표면선량을 $5.5\%$(tray 사용할때 표면선량에서 filter 사용할때 표면선량을 뺀 것) 낮출 수 있었고 $10cm\times10cm$에서는 $11.3\%,\;25cm\times25cm$에서는 $21.3\%$로 낮출 수 있었다. 결론 : 전자오염에 기인한 표면선량은 조사면적에 의존하였고 트레이를 설치했을때 표면의 전자오염은 많았고 특히 조사면적이 클 때 표면의 전자오염은 더욱 증가하였다 표면 및 build-up영역의 선량 특성을 측정한 결과 0.5mm Cu판과 Cu/Al=0.28mm/1.5mm 복합판이 최적 필터로 결정되었다. 트레이 밑에 최적 필터를 부착하면 표면선량을 유효하게 감소시킬 수 있었고 필터의 효과는 조사면적이 클 때 더욱 좋았다.

• 한국표면공학회지
• /
• 제25권5호
• /
• pp.235-252
• /
• 1992

(Ti, Al)N films were deposited on 304 stainless steel sheet by D.C. magnetron sputtering using Al target and Ti plate. The high temperature oxidation of (T, Al)N films with the variation of composition has been investigated. The chemical composition of (Ti, Al)N films with the variation of composition has been investigated. The chemical composition of (Ti, Al)N films was similar to the sputter area ratio of titanium to aluminum target by means of EDS and AES survey. The high temperature oxidation test of (Ti, Al)N showed that (Ti, Al)N has better high temperature resistance than TiN and TiC films. TiC films were cracked at 40$0^{\circ}C$ in air TiN films quickly were oxidised at $600^{\circ}C$, were spalled more than $700^{\circ}C$. But (Ti, Al)N films are relatively stable to$ 900^{\circ}C$. The good resistance to high temperature oxida-tion of (Ti, Al)N films are due to the formation of dense Al2O3 and TiO2 oxide layer. Especially, Al2O3 oxide layer is more important. The results obtained from this study show, it is believe that the (Ti, Al)N film by D.C. magnetron sputtering is promising for the use of high temperature and wear resistance mate-rials.

• 한국전산구조공학회논문집
• /
• 제14권3호
• /
• pp.349-359
• /
• 2001

본 논분은 평판구조물의 동적 시간이력해석을 수행하기 위하여 개발된 사절점 판요소에 대하여 기술하였다. 이 요소는 두꺼운 판에서 발생하는 횡전단 변형효과를 고려하기 위하여 Reissner-Mindlin(RM)가정을 도달하였다. 알려진 바와 같이 RM가정을 바탕으로 개발된 판요소가 얇은 판에 적용되면 전단강성 과대현상(,Shear Locking Phenomenon)을 일으키는데 이를 개선하기 위하여 본 연구에서는 가변형도법을 이용한 대체변형도를 자연좌표계에 준하여 명시적으로 유도하였다. 개발된 저차 판요소는 중앙 차분법을 이용한 명시적인 동적 해석 알고리즘에 적용되었으며 이때 판의 대각질량행렬은 특별집중질량법을 사용하여 형성하였다. 개발된 판의 성능은 수치예제를 통하여 평가하고 검증하였다.

• 한국정밀공학회지
• /
• 제23권5호
• /
• pp.170-176
• /
• 2006

Multi-layered laminate made of ceramic/composite have been developed to prevent penetration by high velocity impact. In this study, three-layered plates consisted of 1) cover layer (glass fiber reinforced polymer), 2) $Al_{2}O_{3}$, ceramic plate, and 3) backing plate (glass fiber reinforced polymer) were fabricated with various conditions and tested for their ballistic protection characteristic. The ceramic composite laminates, with thin backing plate, were completely penetrated by armor piercing projectile. The plate with inserted rubber between ceramic and backing plate showed excellent ballistic protection, though completely penetrated by the second shoot.

• 한국응용과학기술학회지
• /
• 제25권1호
• /
• pp.41-47
• /
• 2008

This study was conducted to made a grid alloy (Pb-Ca-Sn-Al) which has a temporary composition ratio in order to improve the efficiency of lead acid batteries. The positive activity material made a 3BS(tri-basic lead sulfate; $3PbO{\cdot}PbSO_4{\cdot}H_2O$) by a low temperature curing and it evaluates the plate efficiency through the life cycle testing. The initial current capacity of low temperature curing plate was excellent but the life cycle was not good (S1). As for the S2 plate, however, the initial current capacity and the life cycle were superior.

• 열처리공학회지
• /
• 제20권5호
• /
• pp.231-236
• /
• 2007

High velocity oxy-fuel (HVOF) spraying was used to coat Ti(Al,O)/$Al_2O_3$ powder onto the SS41 steel plate. Macrostructure of the coated specimen has been investigated by scanning electron micrograph (SEM). High temperature oxidation behavior of the coated specimen and SS41 steel have been studied. From the results of SEM observation, Ti(Al,O)/$Al_2O_3$ powder was coated well onto the substrate SS41 steel. Porosity onto the coated layer was only 0.38%. The oxidation results showed that Ti(Al,O)/$Al_2O_3$ powder coated SS41 steel have improved little oxidation resistance at $900^{\circ}C$ in air, but improved remarkably oxidation resistance at $800^{\circ}C $ in air compare to the substrate SS41 steel.

• Journal of Welding and Joining
• /
• 제14권4호
• /
• pp.62-70
• /
• 1996

Al or Al-alloy have been known to be able to be claded on various materials by using explosive welding process, however, the intermetallic layer frequently formed along the interface have made this process very complicated. In this study, it was focussed to select the process variables, which can get rid of interfacial layer in the Al-claded steel plate. As a result, it was demonstrated that there was a certain range of explosive thickness which did not form the intermetallic phase as well as the non-bonded area. On the other hand, ultasonic tests performed for identifying the presence of interfacial layer nondestructively showed that it could be applied for the intended purpose but its result was weakly related with the microstructural quality of interface.

• 한국주조공학회지
• /
• 제31권1호
• /
• pp.18-25
• /
• 2011

Effect of Fe and Mn contents on the tensile properties has been studied in Al-9wt%Si-0.3wt%Mg alloy. As Fe content of Al-9wt%Si-0.3wt%Mg-0.5wt%Mn alloy increased from 0.15wt% to 0.45wt%, tensile strength of as-cast alloy decreased from 192 MPa to 174 MPa, and elongation of the alloy also decreased from 4.8% to 4.2%. Decrease of these properties can be explained as the formation of plate shape, ${\beta}-Al_5FeSi$ phase with high Fe/Mn ratio of the alloy. However when Mn content of Al-9wt%Si-0.3wt%Mg-0.45wt%Fe alloy increased from 0.3wt% to 0.5wt%, tensile strength of T6 aged alloy increased from 265 MPa to 275 MPa, and elongation of the alloy increased from 2.3% to 3.6%. These improvements attribute to chinese script, ${\alpha}-Al_{15}(Mn,Fe)_3Si_2$ phase shape-modified from ${\beta}-Al_5FeSi$ phase with low Fe/Mn ratio of the alloy.

• Structural Engineering and Mechanics
• /
• 제86권1호
• /
• pp.69-83
• /
• 2023

Analytical solutions to problems are crucial because they provide high-quality comparison data for assessing the accuracy of numerical solutions. Benchmark analytical solutions for the vibrations of cracked functionally graded material (FGM) plates are not available in the literature because of the high level of complexity of such solutions. On the basis of first-order shear deformation plate theory (FSDT), this study proposes analytical series solutions for the vibrations of FGM rectangular plates with side or internal cracks parallel to an edge of the plates by using Fourier cosine series and the domain decomposition technique. The distributions of FGM properties along the thickness direction are assumed to follow a simple power law. The proposed analytical series solutions are validated by performing comprehensive convergence studies on the vibration frequencies of cracked square plates with various crack lengths and under various boundary condition combinations and by performing comparisons with published results based on various plate theories and the theory of three-dimensional elasticity. The results reveal that the proposed solutions are in excellent agreement with literature results obtained using the Ritz method on the basis of FSDT. The paper also presents tabulations of the first six nondimensional frequencies of cracked rectangular Al/Al2O3 FGM plates with various aspect ratios, thickness-to-width ratios, crack lengths, and FGM power law indices under six boundary condition combinations, the tabulated frequencies can serve as benchmark data for assessing the accuracy of numerical approaches based on FSDT.