• 한국태양에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.34-39
• /
• 2011

Screen printing method is a common way to fabricate the crystalline silicon solar cell with low-cost and high-efficiency. The screen printing metallization use silver paste and aluminum paste for front and rear contact, respectively. Especially the rear contact between aluminum and silicon is important to form the back surface filed (Al-BSF) after firing process. BSF plays an important role to reduces the surface recombination due to $p^+$ doping of back surface. However, Al electrode on back surface leads to bow occurring by differences in coefficient of thermal expansion of the aluminum and silicon. In this paper, we studied the properties of mono crystalline silicon solar cell for rear electrode with aluminum and aluminum-boron in order to characterize bow and BSF of each paste. The 156*156 $m^2$ p-type silicon wafers with $200{\mu}m$ thickness and 0.5-3 ${\Omega}\;cm$ resistivity were used after texturing, diffusion, and antireflection coating. The characteristics of solar cells was obtained by measuring vernier callipers, scanning electron microscope and light current-voltage. Solar cells with aluminum paste on the back surface were achieved with $V_{OC}$ = 0.618V, JSC = 35.49$mA/cm^2$, FF(Fill factor) = 78%, Efficiency = 17.13%.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.211-211
• /
• 2012

The electrical loss of the photo-generated carriers is dominated by the recombination at the metal- semiconductor interface. In order to enhance the performance of the solar cells, many studies have been performed on the surface treatment with passivation layer like SiN, SiO2, Al2O3, and a-Si:H. In this work, Al2O3 thin films were investigated to reduce recombination at surface. The Al2O3 thin films have two advantages, such as good passivation properties and back surface field (BSF) effect at rear surface. It is usually deposited by atomic layer deposition (ALD) technique. However, ALD process is a very expensive process and it has rather low deposition rate. In this study, the ICP-assisted reactive magnetron sputtering method was used to deposit Al2O3 thin films. For optimization of the properties of the Al2O3 thin film, various fabrication conditions were controlled, such as ICP RF power, substrate bias voltage and deposition temperature, and argon to oxygen ratio. Chemical states and atomic concentration ratio were analyzed by x-ray photoelectron spectroscopy (XPS). In order to investigate the electrical properties, Al/(Al2O3 or SiO2,/Al2O3)/Si (MIS) devices were fabricated and characterized using the C-V measurement technique (HP 4284A). The detailed characteristics of the Al2O3 passivation thin films manufactured by ICP-assisted reactive magnetron sputtering technique will be shown and discussed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.430-430
• /
• 2012

The surface recombination velocity of the silicon solar cell could be reduced by passivation with insulating layers such as $SiO_2$, SiNx, $Al_2O_3$, a-Si. Especially, the aluminium oxide has advantages over other materials at rear surface, because negative fixed charge via Al vacancy has an additional back surface field effect (BSF). It can increase the lifetime of the hole carrier in p-type silicon. The aluminium oxide thin film layer is usually deposited by atomic layer deposition (ALD) technique, which is expensive and has low deposition rate. In this study, ICP-assisted reactive magnetron sputtering technique was adopted to overcome drawbacks of ALD technique. In addition, it has been known that by annealing aluminium oxide layer in nitrogen atmosphere, the negative fixed charge effect could be further improved. By using ICP-assisted reactive magnetron sputtering technique, oxygen to nitrogen ratio could be precisely controlled. Fabricated aluminium oxy-nitride (AlON) layer on silicon wafers were analyzed by x-ray photoelectron spectroscopy (XPS) to investigate the atomic concentration ratio and chemical states. The electrical properties of Al/($Al_2O_3$ or $SiO_2/Al_2O_3$)/Si (MIS) devices were characterized by the C-V measurement technique using HP 4284A. The detailed characteristics of the AlON passivation layer will be shown and discussed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.603-603
• /
• 2012

최근에 전면 emitter의 doping profile이 다른 selective emitter solar cell은 실제 제작시단파장 영역에서 많은 gain을 얻을 수 없어 LBC 구조의 태양전지에 관한 연구가 많이 진행되고 있다. 본 연구는 TCAD simulation을 이용하여 후면에 형성되는 locally doped BSF(p++) region의 doping profile의 변화에 따른 태양전지 특성에 관한 연구이다. Al으로 형성되는 local back contact의 doping depth 및 surface concentration에 따른 전기적, 광학적 분석을 통해 주도적인 인자를 분석하고 최적화하였다. 특히 doping depth에 따른 변화보다는 surface concentration의 변화에 따른 특성변화가 주도적으로 나타났다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.216-216
• /
• 2012

The purpose of this work is to investigate a back surface field (BSF) on variety wafer resistivity for industrial crystalline silicon solar cells. As pointed out in this manuscript, doping a crucible grown Cz Si ingot with Ga offers a sure way of eliminating the light induced degradation (LID) because the LID defect is composed of B and O complex. However, the low segregation coefficient of Ga in Si causes a much wider resistivity variation along the Ga doped Cz Si ingot. Because of the resistivity variation the Cz Si wafer from different locations has different performance as know. In the light of B doped wafer, we made wider resistivity in Si ingot; we investigated the how resistivities work on the solar cells performance as a BSF quality.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.38.2-38.2
• /
• 2010

We have studied mechanisms of back contact formation in Al evaporation and screen printed Al paste for Si solar cells by TEM analysis. We observed that Si diffuse into Al during heat up. The Si diffusion process made vacancies in Si wafer. The Al began to seep into the Si wafer (Al spike). During heat down, the Al spike were shrink which causes the doped region (BSF).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2008.02a
• /
• pp.246-246
• /
• 2008

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.1
• /
• pp.57-61
• /
• 2011

To develop high efficiency crystalline solar cells, the rear surface passivation is very important. In this paper, $Al_2O_3$ films deposited by thermal ALD(atomic layer deposition) method were studied for rear surface passivation of crystalline solar cells and their passivation properties were evaluated. After the deposition of $Al_2O_3$ films on p-type Si wafers, the lifetime was increased very much due to the reduction of interface state density and the field effects of the negative fixed charge in the films. Also, optimum annealing condition and effects of SiNx capping layer were investigated. The best lifetime was obtained when the films were annealed at $400^{\circ}C$ for 15min. And the lifetime degradation of the $Al_2O_3$ films with SiNx capping layers was improved compared to those without the capping layers.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.spc3
• /
• pp.194-198
• /
• 2012

Crystalline silicon solar cell remains the major player in the photovoltaic marketplace with 80% of the market, despite the development of various thin film technologies. Silicon's excellent efficiency, stability, material abundance and low toxicity have helped to maintain its position of dominance. However, the cost of silicon materials remains a major barrier to reducing the cost of silicon photovoltaics. Using the crystalline silicon wafer with thinner thickness is the promising way for cost and material reduction in the solar cell production. However, the thinner the silicon wafer is, the worse bow phenomenon is induced. The bow phenomenon is observed when two or more layers of materials with different temperature expansion coefficiencies are in contact, in this case silicon and aluminum. In this paper, the solar cells were fabricated with different thicknesses of Al layer in order to reduce the bow phenomenon. With less amount of paste applications, we observed that the bow could be reduced by up to 40% of the largest value with 120 micron thickness of the wafer even though the conversion efficiency decrease by 0.5% occurred. Since the bowed wafers lead to unacceptable yield losses during the module construction, the reduction of bow is indispensable on thin crystalline silicon solar cell. In this work, we have studied on the counterbalance between the bow and conversion efficiency and also suggest the formation of enough back surface field (BSF) with thinner Al layer application.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.406-406
• /
• 2011

최근 결정질 실리콘 태양전지 분야에서는 태양전지의 Voc와 Isc의 증가를 통한 효율 향상을 목적으로 후면 passivation 박막에 대한 연구가 활발하게 진행되고 있다. Local-Back Contact Cell은 최적화된 후면 passivation 박막을 이용한 태양전지 제조방법이다. 본 연구에서는 고효율의 LBC 태양전지 개발을 위해 Rapid Thermal Oxide(RTO)를 이용한 후면 passivation 박막에 screen printing을 이용한 point contact 구조의 LBC 태양전지를 제작하고 그 특성을 분석하였다. 본 연구에 사용된 RTO 박막은 O2와 N2, 2L/min의 조건에서 $850^{\circ}C$에서 3분 동안 열처리하여 성장시켰다. 이렇게 성장된 박막은 3nm의 두께로 형성되어 passivation 효과를 나타내었으며, carrier lifetime 측정 결과 37.8us의 값을 나타냈다. 전면 ARC형성을 위해 RTO 박막 위에 PECVD를 이용하여 SiNx passivation 처리를 하였고, 그 결과 carrier lifetime은 49.1us까지 향상하였다. 후면의 전극 형성을 위해 screen printing 방법으로 Al point contact을 형성하여 local 한 BSF를 형성 시켰으며, 이후 후면 전극 연결을 위한 방법으로 300nm의 두께로 full Al evaporation 공정을 진행 하였다. 결과적으로 RTO 후면 passivation 박막에 Al point contact 형성을 통해 제작된 태양전지는, Suns-Voc 579mV, FF 82.3%, 16.7%의 효율을 달성하였다.