• International Journal of Aeronautical and Space Sciences
• /
• 제16권4호
• /
• pp.493-499
• /
• 2015

The aerodynamic performance of blunt trailing edge airfoils was investigated. The flow fields around the modified NACA64-418, which consists of the tip blade of the wind turbine and Mexico model of IEA wind, were analyzed. To imitate the repaired airfoil, the original NACA64-418 airfoil, a cambered airfoil, is modified by the adding thickness method, which is accomplished by adding the thickness symmetrically to both sides of the camber line. The thickness ratio of the blunt trailing edge of the modified airfoil, $t_{TE}/t_{max}$, is newly defined to analyze the effects of the blunt trailing edge. The shape functions describing the upper and lower surfaces of the modified NACA64-418 with blunt trailing edge are obtained from the curve fitting of the least square method. To verify the accuracy of the present numerical analysis, the results are first compared with the experimental data of NACA64-418 with high Reynolds number, $Re=6{\times}10^6$, measured in the Langley low-turbulence pressure tunnel. Then, the aerodynamic performance of the modified NACA64-418 is analyzed. The numerical results show that the drag increases, but the lift increases insignificantly, as the trailing edge of the airfoil is thickened. Re-circulation bubbles also develop and increase gradually in size as the thickness ratio of the trailing edge is increased. These re-circulations result in an increase in the drag of the airfoil. The pressure distributions around the modified NACA64-418 are similar, regardless of the thickness ratio of the blunt trailing edge.

• 대한기계학회논문집B
• /
• 제40권5호
• /
• pp.321-327
• /
• 2016

본 연구에서는 고속 회전을 하는 진공청소기용 원심홴의 공력성능 향상을 위해 에어포일 임펠러(Airfoil Impeller)의 적용을 검토 및 연구하였다. 에어포일 최대두께 및 최대두께 위치에 따라 3종의 에어포일 임펠러를 제시하였고, 이때 C4 에어포일 두께분포를 이용하였다. 에어포일 임펠러의 성능 평가는 전산유체역학(Computational Fluid Dynamics) 해석과 흡입일률시험을 통해 수행되었다. 이를 통해 에어포일 형상 적용 시 기존 블레이드 형상에 비하여 임펠러 블레이드 압력면과 디퓨져 블레이드 압력면에서 발생하는 유동박리가 크게 줄어드는 것을 확인하였다. 그리고 이로 인해 기존 원심홴에 비하여 홴 효율이 약 3% 증가 및 비소음이 약 1.3dB(A) 감소되는 것을 확인하였다.

• EDISON SW 활용 경진대회 논문집
• /
• 제5회(2016년)
• /
• pp.203-208
• /
• 2016

In this paper, vibration characteristics in terms of the airfoil cross-sectional shape was examined by using the EDISON co-rotational plane beam-transient analysis. Assuming aircraft wing as a cantilevered beam with a constant cross-sectional shape, natural frequencies of each airfoil shape was compared while varying airfoil maximum thickness and maximum camber length, using Fast Fourier Transformation(FFT). When the airfoil maximum thickness was varied, natural frequency showed peak value at 18% chord, and decreased afterwards. When the airfoil maximum camber length was varied, natural frequency either increased or decreased at 6% chord, while at 8% the natural frequency showed its maximum. Applying such trends to B-737 wing airfoil, an improved B-737_mod airfoil shape was obtained with regard to the vibration characteristics.

• 한국항공우주학회지
• /
• 제40권6호
• /
• pp.475-484
• /
• 2012

익형 풍동시험 시 모델의 제작오차에 의해 시험 익형과 지지대 익형의 두께에서 차이가 있을 경우 시험 익형의 공력특성에 주는 영향을 양력, 항력 및 모멘트 값의 변화를 수치 해석하여 비교 및 분석하였다. 이를 위해 익형모델을 세 부분으로 나누어 제작하는 경우 가운데 위치하는 시험 익형을 기준 형상으로 하여 시험 익형 양쪽에 부착하여 지지대 역할을 하는 익형의 최대두께를 가운데 익형에 비해 작게 설정하였다. 익형모델은 NACA64- 418을 사용하였으며, 난류모델은 천이현상을 잘 예측할 수 있는 Transition SST를 사용하였다. 다양한 받음각과 레이놀즈 수에서 지지대 역할을 하는 익형모델과 두께 차이가 매우 큰 경우에도 가운데 위치한 시험 익형의 공력특성에 미치는 영향이 매우 작음을 확인하였다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.354-357
• /
• 2008

Drag reduction is one of main concerns for commercial aircraft companies than ever because fuel price has been tripled in ten years. In this research, Natural Laminar Flow airfoil is designed and tested to reduce drag at cruise condition, $c_l$=0.3, Re=3.4${\times}$10$^6$ and M=0.6. NLF airfoil is characterized by delayed transition from laminar to turbulent flow, which comes from maintaining favorable pressure gradient to downstream. Transition is predicted by solving Boundary Layer equations in viscous boundary layer and by solving Euler Equation outside the boundary layer. Once boundary layer thickness and momentum thickness are obtained, $e^N$-method is used for transition point prediction. As results, KARI's NLF airfoil is designed and shows better characteristics than NLF-0115. The characteristics are tested and verified at low Reynolds numbers, but at high Reynolds numbers, laminar flow characteristics are not obtainable because of fully turbulent flow over airfoil surfaces. Precious experiences, however, relating NLF airfoil design, subsonic and transonic tests are acquired.

• EDISON SW 활용 경진대회 논문집
• /
• 제3회(2014년)
• /
• pp.562-567
• /
• 2014

본 연구에서는 교육 및 연구를 위한 CFD 해석 프로그램인 EDISON_CFD를 이용하여 Symmetric airfoil(NACA0012)과 Cambered airfoil(NACA4412)의 뒷전 두께에 따른 공력 특성을 분석해보았다. Chord 길이의 0%, 1%, 2%, 3%, 4%에 해당하는 뒷전 두께를 가지는 Blunt trailing edge airfoil의 받음각에 따른 공력 특성을 비교 및 분석하고, 어떠한 장단점을 가지는지 확인하였다. 그 결과 Chord 길이의 1% 뒷전 두께를 가질 때를 제외하면 뒷전 두께가 두꺼워질수록 최대양력계수는 증가하였고, 양항비와 실속각은 감소하였다. 또한, 뒷전 두께가 두꺼워질수록 Symmetric airfoil에서는 받음각 $0^{\circ}$를 기준으로 양력곡선기울기가 증가하였고, Cambered airfoil에서는 전체적으로 양력계수가 증가함과 동시에 양력곡선기울기 또한 증가하는 것을 확인할 수 있었다.

• EDISON SW 활용 경진대회 논문집
• /
• 제5회(2016년)
• /
• pp.632-637
• /
• 2016

This study shows what difference would be made to the aerodynamic characteristic with different thickness ratio of the same airfoil, Eppler 387, at low Reynolds number, at the angle of attack of $0^{\circ}$. Konkuk Univ.'s airfoil has a bigger thickness ratio than that of the original Eppler 387 airfoil. The reason for the thicker camber is a Pt 100 ohm heater mounted inside the Konkuk Univ.'s airfoil and this was assumed to make some differences to aerodynamic characteristic. The comparison of these two airfoils' CFD data, provided by EDSION_CFD, with real experiment that had been made in subsonic wind tunnel at Konkuk Univ. is done. A finer result would come out if the complement of the homogeneity of the wind tunnel's fluid is done in the future.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 1997년도 추계 학술대회논문집
• /
• pp.61-65
• /
• 1997

A two-dimensional airfoil under ground effect in subsonic turbulent flow is calculated by sieving the Navier-Stokes equation. Some numerical results for different NACA four-digit airfoils are presented. The numerical results show that the lift and drag coefficients are strongly influenced by the shape of the region between the lower surface of airfoil and the ground In general, the airfoil with large camber and small thickness is suitable for WIG vehicles

• Advances in Computational Design
• /
• 제7권1호
• /
• pp.69-79
• /
• 2022

In this research, the aeroelastic instability of a tail section manufactured from aluminum isotropic material with different shell thickness investigated. For this purpose, the two degrees of freedom flutter analytical approach are used, which is accompanied with simulation by finite element analysis. Using finite element analysis, the geometry parameters such as the center of mass, the aerodynamic center and the shear center are determined. Also, by simulation of finite element method, the bending and torsional stiffnesses for various thickness of the airfoil section are determined. Furthermore, using Lagrange's methods the equations of motion are derived and modal frequency and critical torsional/bending modes are discussed. The results show that with increasing the thickness of the isotropic airfoil section, the flutter and divergence speeds increased. Compared of the obtained results with other research, indicates a good agreement and reliability of this method.

• Wind and Structures
• /
• 제22권5호
• /
• pp.595-616
• /
• 2016

Providing high starting torque and efficiency simultaneously is a significant challenge for vertical axis wind turbines (VAWTs). In this paper, a new approach is studied in order to modify VAWTs performance and cogging torque. In this approach, J-shaped profiles are exploited in the structure of blades by means of eliminating the pressure side of airfoil from the maximum thickness toward the trailing edge. This new profile is a new type of VAWT airfoil using the lift and drag forces, thereby yielding a better performance at low TSRs. To simulate the fluid flow of the VAWT along with J-shaped profiles originated from NACA0018 and NACA0030, a two-dimensional computational analysis is conducted. The Reynolds Averaged Navier-Stokes (RANS) equations are closed using the two-equation Shear Stress Transport (SST) turbulence model. The main objective of the study is to investigate the effects of J-shaped straight blade thickness on the performance characteristics of VAWT. The results obtained indicate that opting for the higher thickness in J-shaped profiles for the blade sections leads the performance and cogging torque of VAWT to enhance dramatically.