• 대한기계학회논문집B
• /
• 제22권2호
• /
• pp.240-252
• /
• 1998

The purpose of this study is to develop a method for predicting the aerodynamic performance of the low speed airfoils in the 2-dimensional, steady and viscous flow. For this study, the airfoil geometry is specified by adopting the longest chord line system and by considering local surface curvature. In case of the inviscid incompressible flow, the analysis is accomplished by the linearly varying strength vortex panel method and the Karman-Tsien correction law is applied for the inviscid compressible flow analysis. The Goradia integral method is adopted for the boundary layer analysis of the laminar and turbulent flows. Viscous and inviscid solutions are converged by the Lockheed iterative calculating method using the equivalent airfoil geometry. The analysis of the separated flow is performed using the Dvorak and Maskew's method as the basic method. The wake effect is also considered by expressing its geometry using the formula of Summey and Smith when no separation occurs. The computational efficiency is verified by comparing the computational results with experimental data and by the shorter execution time.

• 산업기술연구
• /
• 제15권
• /
• pp.153-168
• /
• 1995

The purpose of this study is to develop a method for predicting the aerodynamic performance of the subsonic airfoils in the 2-dimensional, steady and viscous flow. For this study, the airfoil geometry is specified by adopting the longest chord line system and by considering local surface curvature. In case of the inviscid-incompressible flow, the analysis is accomplished by the linearly varying strength vortex panel method and the Karman-Tsien correction law is applied for the inviscid-compressible flow analysis. The Goradia's integral method and the Truckenbrodt integral method are adopted for the boundary layer analysis of the laminar flow and the turbulent flow respectively. Viscous and inviscid solutions are converged by the Lockheed iterative calculating method using the equivalent airfoil geometry. And the analysis of the seperated flow is performed using the Dvorak and Maskew's method as the basic method. The wake effect is also considered and its geometry expressed by the formula of Summey & Smith when no seperation occurs. A computational efficiency is verified by the comparison of the computational results with experimental data and by the shorter execution time.

• 한국전산유체공학회지
• /
• 제3권1호
• /
• pp.46-53
• /
• 1998

An inverse method for the subsonic and transonic airfoil design was developed using the Euler equations. Two testcases were performed. One was a verification of the method using the supercritical airfoil of the Korean mid-sized (100 passengers class) transport aircraft. The other was the design of an airfoil showing a good cruising performance (L/D ratio) in the high subsonic flow regime. These testcases demonstrated the efficiency and the robustness of the design method in the present study.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.377-380
• /
• 2008

In this study, an aerodynamic shape optimization system was developed to study the optimal shape of airfoil. The system consists of GA (Genetic Algorithm) and CFD code based on the Navier-Stokes equation. Lift-drag ratio is chosen as the object function and optimization is conducted for PARSEC airfoil with nine design variables, which is very efficient in representing the surface geometry of airfoil.

• 항공우주시스템공학회지
• /
• 제10권3호
• /
• pp.9-14
• /
• 2016

Using a multiple regression analysis, a total of 78 low-Reynolds-number airfoils are examined in this paper to clarify the systematic relationships between the geometrical parameters of the airfoils and experimentally-determined aerodynamic coefficients. The results show that the effects of the maximum camber and the maximum thickness regarding the maximum lift and the stalling angle of attack, respectively, are major. The lower-surface flatness of the airfoil is also a crucial geometrical parameter for aerodynamic performance. It is proven here that, generally, the application of the regression equations for an assessment of the aerodynamic performance is relatively acceptable, along with an expectation that the lift-curve slope violates the normality assumption.

• Advances in Computational Design
• /
• 제7권1호
• /
• pp.69-79
• /
• 2022

In this research, the aeroelastic instability of a tail section manufactured from aluminum isotropic material with different shell thickness investigated. For this purpose, the two degrees of freedom flutter analytical approach are used, which is accompanied with simulation by finite element analysis. Using finite element analysis, the geometry parameters such as the center of mass, the aerodynamic center and the shear center are determined. Also, by simulation of finite element method, the bending and torsional stiffnesses for various thickness of the airfoil section are determined. Furthermore, using Lagrange's methods the equations of motion are derived and modal frequency and critical torsional/bending modes are discussed. The results show that with increasing the thickness of the isotropic airfoil section, the flutter and divergence speeds increased. Compared of the obtained results with other research, indicates a good agreement and reliability of this method.

• 한국전산구조공학회논문집
• /
• 제29권5호
• /
• pp.389-395
• /
• 2016

본 논문에서는 Co-Rotational plane beam transient analysis EDISON program(CR-보)를 이용한 에어포일 단면형상 변화에 따른 진동특성 연구를 수행하였다. Co-Rotational 평면 보 해석은 대 회전과 작은 변형률을 갖는 보 해석에 적합하다. 항공기의 날개를 외팔보로 가정하여, VABS를 통한 단면해석과 Fourier 변환을 통해 각 단면형상 변화에 따른 에어포일의 고유진동수를 비교하였다. VABS를 사용하여 단면의 형상과 재료의 적층 정보를 고려한 단면에서의 유한요소 해석을 수행하였다. 에어포일의 재질, spar 유무, 단일 등방성 재료 복합재료, 에어포일 최대두께의 변화에 따라 에어포일의 끝단 진폭과 고유진동수가 변화함을 확인할 수 있었다. 이를 바탕으로 에어포일 고유진동수 변화는 2차 관성모멘트/단면적, 밀도, 영률의 변화에 상당한 영향을 받음을 알 수 있었다.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2001년도 유체기계 연구개발 발표회 논문집
• /
• pp.37-42
• /
• 2001

A computerized axial flow fan design system is developed with the capabilities for predicting the aerodynamic performance and the noise characteristics of fan. In the present study, the basic fan blading design is made by combining vortex distribution scheme with camber line design, airfoil selection, blade thickness distribution and stacking of blade elements. With the designed fan blade geometry, the through-flow field and the performance of fan are analyzed by using the streamline curvature computing scheme with spanwise total pressure loss and flow deviation models. Fan noise is assumed to be generated due to the pressure fluctuation induced by wake vortices of fan blades and to radiate as dipole distribution. The vortex-induced fluctuating pressure on blade surface is calculated by combining thin airfoil theory and the predicted flow field data. The predicted performances, sound pressure level and noise directivity patterns of fan by the present method are favorably compared with the test data of actual fans. Furthermore, the present method is shown to be very useful in designing the blade geometry of new fan and optimizing design variables of the fan to achieve higher efficiency and lower noise level.

• 한국항공우주학회지
• /
• 제33권5호
• /
• pp.18-27
• /
• 2005

세로 정안정성이 우수한 지면효과익기 익형을 최적설계하였다. NURBS 형상함수를 사용하여 형상을 설계하고 Navier-Stokes 해석을 통해 공력특성을 해석하였으며, 반응표면법을 사용하여 최적화하였다. 수치계산 효율성을 증대하고 상용 설계/해석 코드 기반의 자동화된 최적화를 위하여 네트워크 분산환경을 구현한 설계최적화 프레임워크를 사용하였다. 양력 최대화 설계 결과로서 기존의 DHMTU 익형과 유사한 안정성 특성을 가지며 양력특성이 개선된 익형을 얻었으며, 강화된 전방하중 특성과 후방의 반전된 캠버선이 특징적으로 나타났다. 이수 중의 피칭모멘트 변화폭이 감소된 익형도 설계하였으며, 전방하중 경향이 약화되고 양력도 약간 감소한 것으로 나타났다. 기존의 포텐셜 유동에 기반한 설계최적화 결과와 비교함으로써 실용적이며 실제로 구현 가능한 공력특성의 개선을 위해서는 반드시 점성을 고려해서 설계를 해야하며 다양한 익형을 생성시킬 수 있는 형상설계 기능의 중요성을 확인하였다.

• 한국유체기계학회 논문집
• /
• 제11권2호
• /
• pp.55-63
• /
• 2008

An examination of the condition of the flow leaving the impeller exit kinetic energy often accounts for 30-50% of the shaft work input to the compressor stage, and for energy efficiency it is important to recover as much of this as possible. This is the function of the diffuser which follows the impeller. The purpose of this study is to investigate the sensitivity of how compressor performances changes as vaned diffuser geometry is varied. Three kinds of vaned diffusers were studied and its results were compared. First vaned diffuser type is based on NACA airfoil and second is channel diffuser and third is conformal transformation of NACA65(4A10)06 airfoil. Mean-line prediction method was applied to investigate the performance and stability for three kinds of diffusers. And CFD analyses have been done for comparison and detailed interior flow pattern study. NACA65(4A10)06 airfoil showed the widest operating range and higher pressure characteristics than the others.